Datasheet
2011-2013 Microchip Technology Inc. DS40001453E-page 353
PIC16(L)F1847
TABLE 30-3: POWER-DOWN CURRENTS (IPD)
(1,2)
PIC16LF1847
Operating Conditions: (unless otherwise stated)
Low-Power Sleep Mode
PIC16F1847
Low-Power Sleep Mode
Param.
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
D022 — 0.02 1.0 2.4 A 1.8 WDT, BOR and T1OSC disabled,
all Peripherals Inactive
— 0.03 1.5 3.0
A3.0
D022 — 15 35 44 A 1.8 WDT, BOR and T1OSC disabled,
all Peripherals Inactive
— 18 40 48 A 3.0
— 19 45 65 A 5.0
D023 — 0.3 1 3
A 1.8 LPWDT Current (Note 1)
—0.8 2 4 A3.0
D023 — 16 35 44 A 1.8 LPWDT Current (Note 1)
— 19 40 48 A 3.0
— 20 45 65 A 5.0
D023A — 20 25 35
A 1.8 FVR current
—21 27 37
A3.0
D023A — 40 62 65 A 1.8 FVR current
— 50 72 75 A 3.0
— 80 115 120 A 5.0
D024 — 8.0 14 16
A 3.0 BOR Current (Note 1)
D024 — 24 47 50 A 3.0 BOR Current (Note 1)
— 29 55 70 A 5.0
D025 — 0.65 3.5 4.0
A 1.8 T1OSC Current (Note 1)
— 2.3 5.0 6.0 A3.0
D025 — 19 39 45 A 1.8 T1OSC Current (Note 1)
— 21 43 59 A 3.0
— 28 55 75 A 5.0
D026 — 0.03 1.5 3.0
A 1.8 ADC Current (Note 1, 3),
no conversion in progress
— 0.07 2.0 3.5
A3.0
D026 — 18 38 45 A 1.8 ADC Current (Note 1, 3),
no conversion in progress
— 20 43 49 A 3.0
— 22 46 65 A 5.0
D026A* — 250 — —
A 1.8 ADC Current (Note 1, 3),
conversion in progress
—250 — —
A3.0
D026A* — 280 — — A 1.8 ADC Current (Note 1, 3),
conversion in progress
— 280 — — A 3.0
— 280 — — A 5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral
current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD.
3: ADC oscillator source is FRC.