Datasheet

PIC16(L)F1847
DS40001453D-page 354 Preliminary  2011-2013 Microchip Technology Inc.
D026A* — 250 — —
A 1.8 ADC Current (Note 1, 3),
conversion in progress
—250 — —
A3.0
D026A* — 280 — — A 1.8 ADC Current (Note 1, 3),
conversion in progress
— 280 — — A 3.0
— 280 — — A 5.0
D027 — 2.0 6.0 8.0
A 1.8 Cap Sense, Low Power,
CPSRM = 0, CPSRNG = 01
(Note 1)
— 5.0 9.0 12.0 A3.0
D027 — 21 41 45 A 1.8 Cap Sense, Low Power,
CPSRM = 0, CPSRNG = 01
(Note 1)
— 23 47 55 A 3.0
— 29 55 68 A 5.0
D027A — 6.0 9.0 10
A 1.8 Cap Sense, Medium Power,
CPSRM = 0, CPSRNG = 10
(Note 1)
— 8.0 13 14 A3.0
D027A — 21 44 47 A 1.8 Cap Sense, Medium Power
CPSRM = 0, CPSRNG = 10
(Note 1)
— 24 53 60 A 3.0
— 27 57 71 A 5.0
D027B — 13 22 24
A 1.8 Cap Sense, High Power,
CPSRM = 0, CPSRNG = 11
(Note 1)
—35 65 70 A3.0
D027B — 21 44 50 A 1.8 Cap Sense, High Power,
CPSRM = 0, CPSRNG = 11
(Note 1)
— 40 68 80 A 3.0
— 50 78 90 A 5.0
D028 — 8.0 16 17
A 1.8 Comparator,
Low Power, CxSP = 0
(Note 1)
— 9.0 18 19 A3.0
D028 — 28 45 50 A 1.8 Comparator,
Low Power, CxSP = 0
(Note 1)
— 30 56 61 A 3.0
— 32 60 80 A 5.0
D028B — 28 46 48
A 1.8 Comparator,
Normal Power, CxSP = 1
(Note 1)
—29 48 50 A3.0
D028B — 60 80 85 A 1.8 Comparator,
Low Power, CxSP = 1
(Note 1)
— 62 85 90 A 3.0
— 64 90 105 A 5.0
30.3 DC Characteristics: Power-Down Currents (IPD) (Continued)
PIC16LF1847
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C
 TA  +125°C for extended
PIC16F1847
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C
 TA  +125°C for extended
Param.
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral
 current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD.
3: ADC oscillator source is FRC.