Datasheet

PIC16(L)F1825/1829
DS41440C-page 356  2010-2012 Microchip Technology Inc.
Power-down Base Current (I
PD)
(2)
D026A* — 250 — — A 1.8 A/D Current (Note 1, 3),
conversion in progress
—250 — — A3.0
D026A* — 280 — — A 1.8 A/D Current (Note 1, 3),
conversion in progress
— 280 — — A 3.0
— 280 — — A 5.0
D027 — 2.3 5 6 A 1.8 Cap Sense Low-Power
CPSRM = 0, CPSRNG = 01
(Note 1)
—3.5 7 9 A3.0
D027 — 20 41 45 A 1.8 Cap Sense Low-Power
CPSRM = 0, CPSRNG = 01
(Note 1)
— 23 47 55 A 3.0
— 25 55 75 A 5.0
D027A — 5 8 10 A 1.8 Cap Sense Medium-Power
CPSRM = 0, CPSRNG = 10
(Note 1)
— 6.5 13 14 A3.0
D027A — 23 44 47 A 1.8 Cap Sense Medium-Power
CPSRM = 0, CPSRNG = 10
(Note 1)
— 26 53 60 A 3.0
— 29 57 71 A 5.0
D027B — 13 22 24 A 1.8 Cap Sense High-Power
CPSRM = 0, CPSRNG = 11
(Note 1)
—35 45 47 A3.0
D027B — 30 58 65 A 1.8 Cap Sense High-Power
CPSRM = 0, CPSRNG = 11
(Note 1)
— 55 84 90 A 3.0
— 59 95 110 A 5.0
D028 — 6.8 16 17 A 1.8 Comparator Current
Low-Power mode (Note 1)
— 7.3 18 19 A3.0
D028 — 24 45 50 A 1.8 Comparator Current
Low-Power mode (Note 1)
— 27 56 61 A 3.0
— 29 60 80 A 5.0
D028B — 28 46 48 A 1.8 Comparator Current
High-Power mode (Note 1)
—29 48 49 A3.0
D028B — 60 80 85 A 1.8 Comparator Current,
High-Power mode (Note 1)
— 62 85 90 A 3.0
— 64 90 105 A 5.0
30.3 DC Characteristics: PIC16(L)F1825/1829-I/E (Power-Down) (Continued)
PIC16LF1825/1829
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  T
A  +125°C for extended
PIC16F1825/1829
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  T
A  +85°C for industrial
-40°C  T
A  +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base I
DD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base I
DD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD.
3: A/D oscillator source is F
RC.