Datasheet

PIC16(L)F1825/1829
DS41440C-page 100  2010-2012 Microchip Technology Inc.
Even if the flag bits were checked before executing a
SLEEP instruction, it may be possible for flag bits to
become set before the SLEEP instruction completes. To
determine whether a SLEEP instruction executed, test
the PD
bit. If the PD bit is set, the SLEEP instruction
was executed as a NOP.
FIGURE 9-1: WAKE-UP FROM SLEEP THROUGH INTERRUPT
TABLE 9-1: SUMMARY OF REGISTERS ASSOCIATED WITH POWER-DOWN MODE
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Register on
Page
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 90
IOCAF
— —
IOCAF5 IOCAF4 IOCAF3 IOCAF2 IOCAF1 IOCAF0
141
IOCAN
— —
IOCAN5 IOCAN4 IOCAN3 IOCAN2 IOCAN1 IOCAN0
141
IOCAP
— —
IOCAP5 IOCAP4 IOCAP3 IOCAP2 IOCAP1 IOCAP0
140
IOCBF
(1)
IOCBF7 IOCBF6 IOCBF5 IOCBF4 — — — —
142
IOCBN
(1)
IOCBN7 IOCBN6 IOCBN5 IOCBN4 — — — —
142
IOCBP
(1)
IOCBP7 IOCBP6 IOCBP5 IOCBP4 — — — —
141
PIE1 TMR1GIE ADIE RCIE
TXIE SSP1IE CCP1IE TMR2IE TMR1IE 91
PIE2
OSFIE C2IE C1IE EEIE BCL1IE
—
— CCP2IE 92
PIE4
(1)
— — — — — —
BCL2IE SSP2IE
94
PIR1
TMR1GIF ADIF RCIF
TXIF SSP1IF CCP1IF TMR2IF TMR1IF
95
PIR2
OSFIF C2IF C1IF EEIF BCL1IF — — CCP2IF
96
PIR4
(1)
— — — — — —
BCL2IF SSP2IF
98
STATUS
— — —TOPD Z DC C 24
WDTCON
— — WDTPS<4:0> SWDTEN 103
Legend: — Unimplemented, read as ‘0’. Shaded cells are not used in Power-down mode.
Note 1: PIC16(L)F1829 only.
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
(1)
CLKOUT
(2)
Interrupt flag
GIE bit
(INTCON reg.)
Instruction Flow
PC
Instruction
Fetched
Instruction
Executed
PC PC + 1 PC + 2
Inst(PC) = Sleep
Inst(PC - 1)
Inst(PC + 1)
Sleep
Processor in
Sleep
Interrupt Latency
(4)
Inst(PC + 2)
Inst(PC + 1)
Inst(0004h)
Inst(0005h)
Inst(0004h)
Dummy Cycle
PC + 2 0004h 0005h
Dummy Cycle
T
OST
(3)
PC + 2
Note 1: XT, HS or LP Oscillator mode assumed.
2: CLKOUT is not available in XT, HS, or LP Oscillator modes, but shown here for timing reference.
3: TOST = 1024 TOSC (drawing not to scale). This delay applies only to XT, HS or LP Oscillator modes.
4: GIE = 1 assumed. In this case after wake-up, the processor calls the ISR at 0004h. If GIE = 0, execution will continue in-line.