Datasheet
2010-2012 Microchip Technology Inc. DS41419D-page 361
PIC16(L)F1824/1828
30.3 DC Characteristics: PIC16(L)F1824/1828-I/E (Power-Down)
PIC16LF1824/1828
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C T
A +125°C for extended
PIC16F1824/1828
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C T
A +85°C for industrial
-40°C T
A +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
Power-down Base Current (I
PD) (NOTE 2)
D022 — 0.02 1.0 2.4 A 1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 0.03 1.5 3.0 A3.0
D022 — 18 37 44 A 1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 20 42 48 A 3.0
— 22 45 65 A 5.0
D023 — 0.2 2.0 3.0 A 1.8 LPWDT Current (NOTE 1)
— 0.5 2.0 4.0 A3.0
D023 — 18 38 44 A 1.8 LPWDT Current (NOTE 1)
— 21 43 48 A 3.0
— 22 46 65 A 5.0
D023A — 12 22 25 A 1.8 FVR current
—13 24 27 A3.0
D023A — 33 62 65 A 1.8 FVR current
— 40 72 75 A 3.0
— 68 115 120 A 5.0
D024 — 7.0 14 16 A 3.0 BOR Current (NOTE 1)
D024 — 24 47 50 A 3.0 BOR Current (NOTE 1)
— 29 55 70 A 5.0
D025 — 0.65 3.5 4.0 A 1.8 T1OSC Current (NOTE 1)
— 2.3 4.0 4.5 A3.0
D025 — 19 39 45 A 1.8 T1OSC Current (NOTE 1)
— 21 43 59 A 3.0
— 23 55 75 A 5.0
D026 — 0.03 1.5 3.0 A 1.8 A/D Current (NOTE 1, 3),
no conversion in progress
— 0.04 2.0 3.5 A3.0
D026 — 18 38 45 A 1.8 A/D Current (NOTE 1, 3),
no conversion in progress
— 20 43 49 A 3.0
— 22 46 65 A 5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base I
DD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral current can be determined by subtracting the base I
DD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD.
3: A/D oscillator source is F
RC.