Datasheet

PIC16(L)F1826/27
DS41391D-page 348  2011 Microchip Technology Inc.
Power-down Base Current (I
PD)
(2)
D026A* — 250 — — A 1.8 A/D Current (Note 1, Note 3),
conversion in progress
—250 — — A3.0
D026A* — 280 — — A 1.8 A/D Current (Note 1, Note 3),
conversion in progress
— 280 — — A 3.0
— 280 — — A 5.0
D027 — 3.5 6 8 A 1.8 Cap Sense Low Power
Oscillator mode (Note 1)
— 7 10 14 A3.0
D027 — 4.3 36 38 A 1.8 Cap Sense Low Power
Oscillator mode (Note 1)
— 5.8 39 42 A 3.0
— 6.3 42 45 A 5.0
D027A — 4.2 8 10 A 1.8 Cap Sense Medium Power
Oscillator mode (Note 1)
— 6 12 15 A3.0
D027A — 7.4 38 40 A 1.8 Cap Sense Medium Power
Oscillator mode (Note 1)
— 9.7 42 43 A 3.0
— 10.4 46 48 A 5.0
D027B — 6 10 15 A 1.8 Cap Sense High Power
Oscillator mode (Note 1)
—10 14 20 A3.0
D027B — 17 44 50 A 1.8 Cap Sense High Power
Oscillator mode (Note 1)
— 41 68 80 A 3.0
— 50 78 90 A 5.0
D028 — 6.9 11 15 A 1.8 Comparator Current, Low Power
mode, one comparator enabled
(Note 1)
— 7.0 13 16 A3.0
D028 — 24 45 60 A 1.8 Comparator Current, Low Power
mode, one comparator enabled
(Note 1)
— 24.5 60 70 A 3.0
— 25 65 75 A 5.0
D028A — 7.0 12 16 A 1.8 Comparator Current, Low Power
mode, two comparators enabled
(Note 1)
— 7.2 14 17 A3.0
D028A — 24 45 60 A 1.8 Comparator Current, Low Power
mode, two comparators enabled
(Note 1)
— 24.5 60 70 A 3.0
— 25 65 75 A 5.0
30.3 DC Characteristics: PIC16(L)F1826/27-I/E (Power-Down) (Continued)
PIC16LF1826/27
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  T
A  +125°C for extended
PIC16F1826/27
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  T
A  +85°C for industrial
-40°C  T
A  +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base I
DD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base I
DD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins set to inputs state and tied to V
DD.
3: A/D oscillator source is F
RC.