Datasheet
2011 Microchip Technology Inc. DS41391D-page 347
PIC16(L)F1826/27
30.3 DC Characteristics: PIC16(L)F1826/27-I/E (Power-Down)
PIC16LF1826/27
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C T
A +125°C for extended
PIC16F1826/27
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C T
A +85°C for industrial
-40°C T
A +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
Power-down Base Current (I
PD)
(2)
D022 — 0.02 1.0 4.0 A 1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 0.03 1.1 7.0 A3.0
D022 — 15 35 50 A 1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 18 40 60 A 3.0
— 19 45 70 A 5.0
D023 — 0.5 1.1 5.0 A 1.8 LPWDT Current (Note 1)
— 0.8 2.0 8.0 A3.0
D023 — 16 35 50 A 1.8 LPWDT Current (Note 1)
— 19 40 60 A 3.0
— 20 45 70 A 5.0
D023A — 8.5 23 32 A 1.8 FVR current (Note 1)
— 8.5 26 40 A3.0
D023A — 32 62 66 A 1.8 FVR current (Note 1)
— 39 70 80 A 3.0
— 70 110 120 A 5.0
D024 — 8.1 14 20 A 3.0 BOR Current (Note 1)
D024 — 34 57 70 A 3.0 BOR Current (Note 1)
— 67 100 115 A 5.0
D025 — 0.6 1.5 5.0 A 1.8 T1OSC Current (Note 1)
— 0.8 2.5 8.0 A3.0
D025 — 16 35 50 A 1.8 T1OSC Current (Note 1)
— 21 40 60 A 3.0
— 25 45 70 A 5.0
D026 — 0.1 1.1 5.0 A 1.8 A/D Current (Note 1, Note 3), no
conversion in progress
— 0.1 2.0 8.0 A3.0
D026 — 16 35 50 A 1.8 A/D Current (Note 1, Note 3), no
conversion in progress
— 21 40 60 A 3.0
— 25 45 70 A 5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base I
DD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral current can be determined by subtracting the base I
DD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins set to inputs state and tied to V
DD.
3: A/D oscillator source is F
RC.