Datasheet
PIC16(L)F1826/27
DS41391D-page 344 2011 Microchip Technology Inc.
30.2 DC Characteristics: PIC16(L)F1826/27-I/E (Industrial, Extended)
PIC16LF1826/27
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C T
A +125°C for extended
PIC16F1826/27
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C T
A +85°C for industrial
-40°C T
A +125°C for extended
Param
No.
Device
Characteristics
Min. Typ† Max. Units
Conditions
V
DD Note
Supply Current (I
DD)
(1, 2)
D010 — 7.0
13
A1.8
F
OSC = 32 kHz
LP Oscillator mode, -40°C T
A +85°C
—9.0
16
A3.0
—7.0
17
A1.8
F
OSC = 32 kHz
LP Oscillator mode, -40°C T
A +125°C
—9.0
18
A3.0
D010 — 24
40
A 1.8
FOSC = 32 kHz
LP Oscillator mode
-40°C T
A +85°C
— 30
48
A 3.0
— 32
55
A 5.0
— 24
43
A 1.8
FOSC = 32 kHz
LP Oscillator mode
-40°C T
A +125°C
— 30
50
A 3.0
— 32
60
A 5.0
D011 — 110
200
A1.8F
OSC = 1 MHz
XT Oscillator mode
— 200
400
A3.0
D011 — 160
210
A 1.8 FOSC = 1 MHz
XT Oscillator mode
— 210
400
A 3.0
— 250
450
A 5.0
D012 — 290
475
A1.8F
OSC = 4 MHz
XT Oscillator mode
— 600
900
A3.0
D012 — 380
570
A 1.8 FOSC = 4 MHz
XT Oscillator mode
— 650
880
A 3.0
— 680
1100
A 5.0
D013 — 40
80
A1.8F
OSC = 500 kHz
EC Oscillator mode, Low-power mode
—70
120
A3.0
D013 — 60
120
A 1.8 FOSC = 500 kHz
EC Oscillator mode
Low-power mode
— 80
180
A 3.0
— 93
200
A 5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins as inputs, pulled to V
DD; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
3: 8 MHz internal RC oscillator with 4x PLL enabled.
4: 8 MHz crystal oscillator with 4x PLL enabled.
5: For RC oscillator configurations, current through R
EXT is not included. The current through the resistor can be extended
by the formula I
R = VDD/2REXT (mA) with REXT in k.