Datasheet
PIC16(L)F1824/1828
DS41419D-page 358 2010-2012 Microchip Technology Inc.
30.2 DC Characteristics: PIC16(L)F1824/1828-I/E (Industrial, Extended)
PIC16LF1824/1828
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C T
A +125°C for extended
PIC16F1824/1828
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C T
A +85°C for industrial
-40°C T
A +125°C for extended
Param
No.
Device
Characteristics
Min. Typ† Max. Units
Conditions
V
DD Note
Supply Current (I
DD) (NOTE 1, 2)
D010 — 5.0
10
A1.8
F
OSC = 32 kHz
LP Oscillator mode, -40°C T
A +85°C
—7.5
12
A3.0
D010 — 24
50
A 1.8
FOSC = 32 kHz
LP Oscillator mode, -40°C T
A +85°C
— 30
55
A 3.0
— 32
60
A 5.0
D010A — 5.0 13 A1.8
F
OSC = 32 kHz
LP Oscillator mode, -40°C T
A +125°C
—7.5 15 A3.0
D010A — 24
55
A 1.8
FOSC = 32 kHz
LP Oscillator mode, -40°C T
A +125°C
— 30
60
A 3.0
— 32
65
A 5.0
D011 — 88
110
A1.8F
OSC = 1 MHz
XT Oscillator mode
— 133
190
A3.0
D011 — 110
130
A 1.8 FOSC = 1 MHz
XT Oscillator mode
— 155
220
A 3.0
— 180
290
A 5.0
D012 — 220
290
A1.8F
OSC = 4 MHz
XT Oscillator mode
— 370
480
A3.0
D012 — 238
300
A 1.8 FOSC = 4 MHz
XT Oscillator mode
— 390
500
A 3.0
— 447
700
A 5.0
D013 — 55
160
A1.8F
OSC = 1 MHz
EC Oscillator mode, Medium-Power mode
—90
230
A3.0
D013 — 75
180
A 1.8 FOSC = 1 MHz
EC Oscillator mode
Medium-Power mode
— 116
240
A 3.0
— 145
320
A 5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to V
DD; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
3: 8 MHz internal oscillator with 4xPLL enabled.
4: 8 MHz crystal oscillator with 4xPLL enabled.
5: For RC oscillator configurations, current through R
EXT is not included. The current through the resistor can be extended
by the formula I
R = VDD/2REXT (mA) with REXT in k.