Datasheet

 2010-2012 Microchip Technology Inc. DS41413C-page 349
PIC12(L)F1822/PIC16(L)F1823
30.3 DC Characteristics: PIC12(L)F1822/PIC16(L)F1823-I/E (Power-Down)
PIC12LF1822/16LF1823
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  T
A  +125°C for extended
PIC12F1822/16F1823
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  T
A  +85°C for industrial
-40°C  T
A  +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
Power-down Base Current (I
PD)
(2)
D022 — 0.02 1.0 4.0 A 1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 0.03 1.8 4.8 A3.0
D022 — 20 40 50 A 1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 22 45 55 A 3.0
— 24 50 60 A 5.0
D023 — 0.3 1.8 10.5 A 1.8 LPWDT Current (Note 1)
—0.52.0 16 A3.0
D023 — 20 41 56 A 1.8 LPWDT Current (Note 1)
— 22 46 61 A 3.0
— 24 51 71 A 5.0
D023A — 12 25 35 A 1.8 FVR current (Note 1)
—13 27 37 A3.0
D023A — 32 65 70 A 1.8 FVR current (Note 1)
— 38 75 80 A 3.0
— 68 115 120 A 5.0
D024 — 8.0 15 20 A 3.0 BOR Current (Note 1)
D024 — 30 55 65 A 3.0 BOR Current (Note 1)
— 33 75 85 A 5.0
D025 — 0.65 4.0 7.0 A 1.8 T1OSC Current (Note 1)
— 2.3 4.5 7.5 A3.0
D025 — 20 42 55 A 1.8 T1OSC Current (Note 1)
— 23 45 60 A 3.0
— 25 48 70 A 5.0
D026 — 0.1 1.8 4.0 A 1.8 A/D Current (Note 1, Note 3), no
conversion in progress
— 0.1 2.0 5.0 A3.0
D026 — 20 40 55 A 1.8 A/D Current (Note 1, Note 3), no
conversion in progress
— 22 45 60 A 3.0
— 24 50 70 A 5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base I
DD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base I
DD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD.
3: A/D oscillator source is F
RC.