Datasheet

 2011-2012 Microchip Technology Inc. Preliminary DS41579D-page 375
PIC16(L)F1782/3
30.3 DC Characteristics: PIC16(L)F1782/3-I/E (Power-Down)
PIC16LF1782/3
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C
 TA  +125°C for extended
PIC16F1782/3
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C
 TA  +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
Power-down Base Current (I
PD)
(2, 5)
D023 — 0.05 1.0 8.0 A 1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 0.08 2.0 9.0
A3.0
D023 — 0.3 3 11 A 2.3 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 0.4 4 12 A 3.0
— 0.5 6 15 A 5.0
D024 — 0.5 6 14
A 1.8 LPWDT Current (Note 1)
—0.8 7 17 A3.0
D024 — 0.8 6 15 A 2.3 LPWDT Current (Note 1)
— 0.9 7 20 A 3.0
— 1.0 8 22 A 5.0
D025 — 15 28 30
A 1.8 FVR Current
—1830 33
A3.0
D025 — 18 33 35 A 2.3 FVR Current (Note 4)
— 19 35 37 A 3.0
— 20 37 39 A 5.0
D026 — 7.5 25 28
A 3.0 BOR Current (Note 1)
D026 — 40 25 28 A 3.0 BOR Current (Note 1, Note 4)
— 87 28 31 A 5.0
D027 — 1 4 8
A 3.0 LPBOR Current (Note 1)
D028 — 0.5 5 9 A 1.8 SOSC Current (Note 1)
—0.88.5 12 A3.0
D028 — 1.1 6 10 A 2.3 SOSC Current (Note 1)
— 1.3 8.5 20 A 3.0
— 1.4 10 25 A 5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Legend: TBD = To Be Determined
Note 1: The peripheral current is the sum of the base IPD and the additional current consumed when this peripheral is enabled.
The peripheral
 current can be determined by subtracting the base IDD or IPD current from this limit. Max values should
be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD, and VREGCON = 0x03.
3: ADC oscillator source is FRC.
4: 0.1 F capacitor on VCAP.
5: VREGPM = 1.