Datasheet

PIC16(L)F1526/7
DS41458C-page 284  2011-2013 Microchip Technology Inc.
22.5.2.3 EUSART Synchronous Slave
Reception
The operation of the Synchronous Master and Slave
modes is identical (
Section 22.5.1.5 “Synchronous
Master Reception”
), with the following exceptions:
• Sleep
• CREN bit is always set, therefore the receiver is
never Idle
• SREN bit, which is a “don’t care” in Slave mode
A character may be received while in Sleep mode by
setting the CREN bit prior to entering Sleep. Once the
word is received, the RSR register will transfer the data
to the RCxREG register. If the RCxIE enable bit is set,
the interrupt generated will wake the device from Sleep
and execute the next instruction. If the GIE bit is also
set, the program will branch to the interrupt vector.
22.5.2.4 Synchronous Slave Reception
Set-up:
1. Set the SYNC and SPEN bits and clear the
CSRC bit.
2. Set the RXx/DTx and TXx/CKx TRIS controls to
‘1’.
3. If using interrupts, ensure that the GIE and PEIE
bits of the INTCON register are set and set the
RCxIE bit.
4. If 9-bit reception is desired, set the RX9 bit.
5. Set the CREN bit to enable reception.
6. The RCxIF bit will be set when reception is
complete. An interrupt will be generated if the
RCxIE bit was set.
7. If 9-bit mode is enabled, retrieve the Most
Significant bit from the RX9D bit of the RCxSTA
register.
8. Retrieve the 8 Least Significant bits from the
receive FIFO by reading the RCxREG register.
9. If an overrun error occurs, clear the error by
either clearing the CREN bit of the RCxSTA
register or by clearing the SPEN bit which resets
the EUSART.
TABLE 22-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Register
on Page
BAUD1CON
ABDOVF RCIDL — SCKP BRG16 — WUE ABDEN 267
BAUD2CON ABDOVF RCIDL — SCKP BRG16 — WUE ABDEN 267
INTCON GIE PEIE
TMR0IE INTE IOCIE TMR0IF INTF IOCIF 92
PIE1 TMR1GIE ADIE RC1IE TX1IE SSP1IE CCP1IE TMR2IE TMR1IE 93
PIE4
CCP10IE CCP9IE RC2IE TX2IE CCP8IE CCP7IE BCL2IE SSP2IE 96
PIR1 TMR1GIF ADIF RC1IF TX1IF SSP1IF CCP1IF TMR2IF TMR1IF 97
PIR4
CCP10IF CCP9IF RC2IF TX2IF CCP8IF CCP7IF BCL2IF SSP2IF 96
RC1REG EUSART1 Receive Register 260*
RC1STA SPEN RX9 SREN CREN
ADDEN FERR OERR RX9D 266
RC2REG EUSART2 Receive Register 260*
RC2STA SPEN RX9 SREN CREN
ADDEN FERR OERR RX9D 266
SP1BRGL EUSART1 Baud Rate Generator, Low Byte 268*
SP1BRGH EUSART1 Baud Rate Generator, High Byte 268*
SP2BRGL EUSART2 Baud Rate Generator, Low Byte 268*
SP2BRGH EUSART2 Baud Rate Generator, High Byte 268*
TX1STA CSRC
TX9 TXEN SYNC SENDB BRGH TRMT TX9D 265
TX2STA CSRC
TX9 TXEN SYNC SENDB BRGH TRMT TX9D 265
Legend: — = unimplemented locations, read as ‘0’. Shaded bits are not used for synchronous slave reception.
* Page provides register information.