Datasheet
2010-2013 Microchip Technology Inc. DS40001452D-page 285
PIC16(L)F1516/7/8/9
25.3 DC Characteristics: Power-Down Currents (IPD)
PIC16LF1516/7/8/9
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C
TA +125°C for extended
PIC16F1516/7/8/9
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C
TA +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
Power-down Currents (I
PD)
(2, 4)
D022 Base IPD — 0.02 1.0 8.0 A 1.8 WDT, BOR, FVR, and SOSC
disabled, all Peripherals Inactive
— 0.03 2.0 9.0
A3.0
D022 Base IPD — 0.20 3.0 10 A 2.3 WDT, BOR, FVR, and SOSC
disabled, all Peripherals Inactive,
Low-power regulator active
— 0.30 4.0 12 A 3.0
— 0.47 6.0 15 A 5.0
D023 — 0.50 6.0 14
A 1.8 LPWDT Current (Note 1)
— 0.80 7.0 17 A3.0
D023 — 0.50 6.0 15 A 2.3 LPWDT Current (Note 1)
— 0.77 7.0 20 A 3.0
— 0.85 8.0 22 A 5.0
D023A — 8.5 23 25
A 1.8 FVR current (Note 1)
— 8.5 24 27 A3.0
D023A — 18 26 30 A 2.3 FVR current (Note 1)
— 19 27 37 A 3.0
— 20 29 45 A 5.0
D024 — 8.0 17 20
A 3.0 BOR Current (Note 1)
D024 — 8.0 17 30 A 3.0 BOR Current (Note 1)
— 9.0 20 40 A 5.0
D024A — 0.30 4.0 8.0
A 3.0 LPBOR Current
D024A — 0.30 4.0 14 A 3.0 LPBOR Current (Note 1)
— 0.45 8.0 17 A 5.0
D025 — 0.3 5.0 9.0
A 1.8 SOSC Current (Note 1)
—0.58.5 12 A3.0
D025 — 1.1 6.0 10 A 2.3 SOSC Current (Note 1)
— 1.3 8.5 20 A 3.0
— 1.4 10 25 A 5.0
D026 — 0.10 1.0 9.0
A 1.8 ADC Current (Note 1, 3),
no conversion in progress
— 0.10 2.0 10
A3.0
D026 — 0.16 3.0 10 A 2.3 ADC Current (Note 1, 3),
no conversion in progress
— 0.40 4.0 11 A 3.0
— 0.50 6.0 16 A 5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current can be determined by subtracting the base IPD current from this limit. Max values should be
used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD.
3: ADC clock source is FRC.
4: VREGPM = 1, PIC16F1516/7/8/9 only.