Datasheet

PIC16(L)F1512/3
DS41624B-page 300 Preliminary  2012 Microchip Technology Inc.
25.3 DC Characteristics: PIC16(L)F1512/3-I/E (Power-Down)
PIC16LF1512/3
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C
 TA  +125°C for extended
PIC16F1512/3
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C
 TA  +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
Power-down Base Current (I
PD)
(2),(4)
D022 — 0.02 1.0 8.0 A 1.8 WDT, BOR, FVR, and SOSC
disabled, all Peripherals Inactive
— 0.03 2.0 9.0
A3.0
D022 — 0.30 2.0 11 A 2.3 WDT, BOR, FVR, and SOSC
disabled, all Peripherals Inactive
— 0.40 3.0 12 A 3.0
— 0.50 6 15 A 5.0
D023 — 0.50 6 14
A 1.8 LPWDT Current (Note 1)
—0.80 7 17 A3.0
D023 — 0.50 6 15 A 2.3 LPWDT Current (Note 1)
— 0.77 7 20 A 3.0
— 0.85 8 22 A 5.0
D023A — 8.5 23 25
A 1.8 FVR current (Note 1)
— 8.5 24 27 A3.0
D023A — 18 26 30 A 2.3 FVR current (Note 1)
— 19 27 37 A 3.0
— 20 29 45 A 5.0
D024 — 8.0 17 20
A 3.0 BOR Current (Note 1)
D024 — 8 17 30 A 3.0 BOR Current (Note 1)
— 9 20 40 A 5.0
D024A — 0.30 4 8
A 3.0 LPBOR Current
D024A — 0.30 4 14 A 3.0 LPBOR Current
— 0.45 8 17 A 5.0
D025 — 0.6 5 9
A 1.8 SOSC Current (Note 1)
—1.88.5 12 A3.0
D025 — 0.7 6 10 A 2.3 SOSC Current (Note 1)
— 3 8.5 20 A 3.0
— 6 10 25 A 5.0
D026 — 0.1 1 9
A 1.8 A/D Current (Note 1, Note 3), no
conversion in progress
—0.1 2 10
A3.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral
 current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD.
3: A/D oscillator source is FRC.
4: Specification for PIC16F1512/3 devices assumes that Low-Power Sleep mode is selected, when available, via the
VREGCON register (see
Section 8.2.2 “Peripheral Usage in Sleep” and Register 8-1).