Datasheet
PIC16C77X
1999-2013 Microchip Technology Inc. Advance Information DS30275B-page 129
FIGURE 12-2: CRYSTAL/CERAMIC
RESONATOR OPERATION
(HS, XT OR LP
OSC CONFIGURATION)
FIGURE 12-3: EXTERNAL CLOCK INPUT
OPERATION (HS OSC
CONFIGURATION)
TABLE 12-1 CERAMIC RESONATORS
TABLE 12-2 CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
Ranges Tested:
Mode Freq OSC1 OSC2
XT 455 kHz
2.0 MHz
4.0 MHz
68 - 100 pF
15 - 68 pF
15 - 68 pF
68 - 100 pF
15 - 68 pF
15 - 68 pF
HS 8.0 MHz
16.0 MHz
10 - 68 pF
10 - 22 pF
10 - 68 pF
10 - 22 pF
These values are for design guidance only. See
notes at bottom of page.
Resonators Used:
455 kHz Panasonic EFO-A455K04B 0.3%
2.0 MHz Murata Erie CSA2.00MG 0.5%
4.0 MHz Murata Erie CSA4.00MG 0.5%
8.0 MHz Murata Erie CSA8.00MT 0.5%
16.0 MHz Murata Erie CSA16.00MX 0.5%
All resonators used did not have built-in capacitors.
Note1: See Table 12-1 and Table 12-2 for recom-
mended values of C1 and C2.
2: A series resistor (RS) may be required for
AT strip cut crystals.
3: RF varies with the crystal chosen.
C1
(1)
C2
(1)
XTAL
OSC2
OSC1
RF
(3)
SLEEP
To
logic
PIC16C77X
RS
(2)
internal
OSC1
OSC2
Open
Clock from
ext. system
PIC16C77X
Osc Type
Crystal
Freq
Cap. Range
C1
Cap. Range
C2
LP 32 kHz 33 pF 33 pF
200 kHz 15 pF 15 pF
XT 200 kHz 47-68 pF 47-68 pF
1 MHz 15 pF 15 pF
4 MHz 15 pF 15 pF
HS 4 MHz 15 pF 15 pF
8 MHz 15-33 pF 15-33 pF
20 MHz 15-33 pF 15-33 pF
These values are for design guidance only. See
notes at bottom of page.
Crystals Used
32 kHz Epson C-001R32.768K-A ± 20 PPM
200 kHz STD XTL 200.000KHz ± 20 PPM
1 MHz ECS ECS-10-13-1 ± 50 PPM
4 MHz ECS ECS-40-20-1 ± 50 PPM
8 MHz EPSON CA-301 8.000M-C ± 30 PPM
20 MHz EPSON CA-301 20.000M-C ± 30 PPM
Note 1: Recommended values of C1 and C2 are
identical to the ranges tested (Table 12-1).
2: Higher capacitance increases the stability
of oscillator but also increases the start-up
time.
3: Since each resonator/crystal has its own
characteristics, the user should consult the
resonator/crystal manufacturer for appropri-
ate values of external components.
4: Rs may be required in HS mode as well as
XT mode to avoid overdriving crystals with
low drive level specification.
774.book Page 129 Tuesday, January 29, 2013 12:02 PM