Datasheet

ManualsBrandsMICROCHIP TECHNOLOGY ManualsMicrocontrollers, Microprocessors & QuartzesEmbedded microcontroller PDIP 40 8-Bit 4 MHz I/O number 33

 1997 Microchip Technology Inc. DS30390E-page 23

PIC16C7X

4.2.2 SPECIAL FUNCTION REGISTERS

The Special Function Registers are registers used by

the CPU and Peripheral Modules for controlling the

desired operation of the device. These registers are

implemented as static RAM.

The special function registers can be classiﬁed into two

sets (core and peripheral). Those registers associated

with the “core” functions are described in this section,

and those related to the operation of the peripheral fea-

tures are described in the section of that peripheral fea-

ture.

TABLE 4-1: PIC16C72 SPECIAL FUNCTION REGISTER SUMMARY

Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

Value on:

POR,

BOR

Value on all

other resets

(3)

Bank 0

00h

(1)

INDF Addressing this location uses contents of FSR to address data memory (not a physical register) 0000 0000 0000 0000

01h TMR0 Timer0 module’s register xxxx xxxx uuuu uuuu

02h

(1)

PCL Program Counter's (PC) Least Signiﬁcant Byte 0000 0000 0000 0000

03h

(1)

STATUS IRP

(4)

RP1

(4)

RP0 TO PD ZDCC0001 1xxx 000q quuu

04h

(1)

FSR Indirect data memory address pointer xxxx xxxx uuuu uuuu

05h PORTA — — PORTA Data Latch when written: PORTA pins when read --0x 0000 --0u 0000

06h PORTB PORTB Data Latch when written: PORTB pins when read xxxx xxxx uuuu uuuu

07h PORTC PORTC Data Latch when written: PORTC pins when read xxxx xxxx uuuu uuuu

08h — Unimplemented — —

09h — Unimplemented — —

0Ah

(1,2)

PCLATH — — — Write Buffer for the upper 5 bits of the Program Counter ---0 0000 ---0 0000

0Bh

(1)

INTCON GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u

0Ch PIR1 — ADIF — — SSPIF CCP1IF TMR2IF TMR1IF -0-- 0000 -0-- 0000

0Dh — Unimplemented — —

0Eh TMR1L Holding register for the Least Signiﬁcant Byte of the 16-bit TMR1 register xxxx xxxx uuuu uuuu

0Fh TMR1H Holding register for the Most Signiﬁcant Byte of the 16-bit TMR1 register xxxx xxxx uuuu uuuu

10h T1CON — — T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu

11h TMR2 Timer2 module’s register 0000 0000 0000 0000

12h T2CON — TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000

13h SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register xxxx xxxx uuuu uuuu

14h SSPCON WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0 0000 0000 0000 0000

15h CCPR1L Capture/Compare/PWM Register (LSB) xxxx xxxx uuuu uuuu

16h CCPR1H Capture/Compare/PWM Register (MSB) xxxx xxxx uuuu uuuu

17h CCP1CON — — CCP1X CCP1Y CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000

18h — Unimplemented — —

19h — Unimplemented — —

1Ah — Unimplemented — —

1Bh — Unimplemented — —

1Ch — Unimplemented — —

1Dh — Unimplemented — —

1Eh ADRES A/D Result Register xxxx xxxx uuuu uuuu

1Fh ADCON0 ADCS1 ADCS0 CHS2 CHS1 CHS0 GO/DONE — ADON 0000 00-0 0000 00-0

Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented read as '0'.

Shaded locations are unimplemented, read as ‘0’.

Note 1: These registers can be addressed from either bank.

2: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<12:8> whose

contents are transferred to the upper byte of the program counter.

3: Other (non power-up) resets include external reset through MCLR and Watchdog Timer Reset.

4: The IRP and RP1 bits are reserved on the PIC16C72, always maintain these bits clear.