Datasheet

PIC16C7X
DS30390E-page 186  1997 Microchip Technology Inc.
Applicable Devices 72 73 73A 74 74A 76 77
18.3 DC Characteristics: PIC16C73/74-04 (Commercial, Industrial)
PIC16C73/74-10 (Commercial, Industrial)
PIC16C73/74-20 (Commercial, Industrial)
PIC16LC73/74-04 (Commercial, Industrial)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40˚C ≤ T
A ≤ +85˚C for industrial and
0˚C ≤ T
A ≤ +70˚C for commercial
Operating voltage V
DD range as described in DC spec Section 18.1 and
Section 18.2.
Param
No.
Characteristic Sym Min Typ
†
Max Units Conditions
Input Low Voltage
I/O ports V
IL
D030 with TTL buffer VSS - 0.15VDD V For entire VDD range
D030A V
SS - 0.8V V 4.5V ≤ VDD ≤ 5.5V
D031 with Schmitt Trigger buffer V
SS - 0.2VDD V
D032 MCLR
, OSC1 (in RC mode) VSS - 0.2VDD V
D033 OSC1 (in XT, HS and LP) V
SS - 0.3VDD V Note1
Input High Voltage
I/O ports V
IH -
D040 with TTL buffer 2.0 - V
DD V 4.5V ≤ VDD ≤ 5.5V
D040A 0.25V
DD
+ 0.8V
-VDD V For entire VDD range
D041 with Schmitt Trigger buffer 0.8V
DD -VDD V For entire VDD range
D042 MCLR
0.8VDD -VDD V
D042A OSC1 (XT, HS and LP) 0.7V
DD -VDD V Note1
D043 OSC1 (in RC mode) 0.9V
DD -VDD V
D070 PORTB weak pull-up current I
PURB 50 250 400 µAVDD = 5V, VPIN = VSS
Input Leakage Current
(Notes 2, 3)
D060 I/O ports I
IL --±1µA Vss ≤ VPIN ≤ VDD, Pin at hi-imped-
ance
D061 MCLR
, RA4/T0CKI - - ±5 µA Vss ≤ VPIN ≤ VDD
D063 OSC1 - - ±5 µA Vss ≤ VPIN ≤ VDD, XT, HS and LP osc
configuration
Output Low Voltage
D080 I/O ports V
OL - - 0.6 V IOL = 8.5 mA, VDD = 4.5V,
-40°C to +85°C
D083 OSC2/CLKOUT (RC osc config) - - 0.6 V I
OL = 1.6 mA, VDD = 4.5V,
-40°C to +85°C
Output High Voltage
D090 I/O ports (Note 3) V
OH VDD - 0.7 - - V IOH = -3.0 mA, VDD = 4.5V,
-40°C to +85°C
D092 OSC2/CLKOUT (RC osc config) V
DD - 0.7 - - V IOH = -1.3 mA, VDD = 4.5V,
-40°C to +85°C
D150* Open-Drain High Voltage V
OD - - 14 V RA4 pin
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C7X be driven with external clock in RC mode.
2: The leakage current on the MCLR
pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.