Datasheet
PIC16C62X
DS30235J-page 96 2003 Microchip Technology Inc.
12.4 DC Characteristics: PIC16C62X/C62XA/CR62XA (Commercial, Industrial, Extended)
PIC16LC62X/LC62XA/LCR62XA (Commercial, Industrial, Extended)
PIC16C62X/C62XA/CR62XA
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ T
A ≤ +85°C for industrial and
0°C ≤ T
A ≤ +70°C for commercial and
-40°C ≤ T
A ≤ +125°C for extended
PIC16LC62X/LC62XA/LCR62XA
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ T
A ≤ +85°C for industrial and
0°C ≤ T
A ≤ +70°C for commercial and
-40°C ≤ T
A ≤ +125°C for extended
Param.
No.
Sym Characteristic Min Typ† Max Units Conditions
VIL Input Low Voltage
I/O ports
D030 with TTL buffer V
SS —0.8V
0.15 V
DD
VVDD = 4.5V to 5.5V
otherwise
D031 with Schmitt Trigger input VSS — 0.2 VDD V
D032 MCLR
, RA4/T0CKI,OSC1 (in RC mode) Vss — 0.2 VDD V (Note 1)
D033 OSC1 (in XT and HS) Vss —
0.3 V
DD
V
OSC1 (in LP) Vss —
0.6 V
DD-
1.0
V
VIL Input Low Voltage
I/O ports
D030 with TTL buffer VSS — 0.8V
0.15 V
DD
V VDD = 4.5V to 5.5V
otherwise
D031 with Schmitt Trigger input VSS — 0.2 VDD V
D032 MCLR, RA4/T0CKI,OSC1 (in RC mode) Vss — 0.2 VDD V (Note 1)
D033 OSC1 (in XT and HS) Vss —
0.3 VDD
V
OSC1 (in LP) Vss —
0.6 VDD-
1.0
V
VIH Input High Voltage
I/O ports
D040 with TTL buffer 2.0V
0.25 V
DD
+ 0.8V
—V
DD
VDD
VVDD = 4.5V to 5.5V
otherwise
D041 with Schmitt Trigger input 0.8 V
DD —
V
DD
D042 MCLR RA4/T0CKI 0.8 VDD —
V
DD
V
D043
D043A
OSC1 (XT, HS and LP)
OSC1 (in RC mode)
0.7 V
DD
0.9 VDD
—
V
DD
V
(Note 1)
* These parameters are characterized but not tested.
† Data in "Typ" column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1:
In RC oscillator configuration, the OSC1 pin is a Schmitt Trigger input. It is not recommended that the PIC16C62X(A) be driven
with external clock in RC mode.
2: The leakage current on the MCLR pin is strongly dependent on applied voltage level. The specified levels represent normal
operating conditions. Higher leakage current may be measured at different input voltages
.
3:
Negative current is defined as coming out of the pin.