Datasheet
PIC12F752/HV752
DS41576B-page 150 Preliminary 2011 Microchip Technology Inc.
CM2CON1 9Ch 0000 ---0 0000 ---0 uuuu ---u
CM1CON0 9Dh 0000 0100 0000 0100 uuuu uuuu
CM1CON1 9Eh 0000 ---0 0000 ---0 uuuu ---u
CMOUT 9Fh ---- --00 ---- --00 ---- --uu
LATA 105h --xx -xxx --uu -uuu --uu -uuu
IOCAN 108h --00 0000 --00 0000 --uu uuuu
WPUA 10Ch --00 0000 --00 0000 --uu uuuu
SLRCON0 10Dh ---- -0-0 ---- -0-0 ---- -u-u
PCON 10Fh ---- --qq ---- --uu
(1, 5)
---- --uu
TMR2 110h 0000 0000 0000 0000 uuuu uuuu
PR2 111h 1111 1111 1111 1111 uuuu uuuu
T2CON 112h -000 0000 -000 0000 -uuu uuuu
HLTMR1 113h
0000 0000
0000 0000
uuuu uuuu
HLTPR1 114h
1111 1111
1111 1111
uuuu uuuu
HLT1CON0 115h
-000 0000 -000 0000 -uuu uuuu
HLT1CON1 116h
---0 0000 ---0 0000 ---u uuuu
ANSELA 185h --11 -111 --11 -111 --uu -uuu
APFCON 188h ---0 -000 ---0 -000 ---u -uuu
OSCTUNE 189h ---0 0000 ---u uuuu ---u uuuu
PMCON1 18Ch ---- -000 ---- -000 ---- -uuu
PMCON2 18Dh ---- ---- ---- ---- ---- ----
PMADRL 18Eh 0000 0000 0000 0000 uuuu uuuu
PMADRH 18Fh ---- --00 ---- --00 ---- --uu
PMDATL 190h 0000 0000 0000 0000 uuuu uuuu
PMDATH 191h --00 0000 --00 0000 --uu uuuu
COG1PH 192h ---- xxxx ---- uuuu ---- uuuu
COG1BLK 193h xxxx xxxx uuuu uuuu uuuu uuuu
COG1DB 194h xxxx xxxx uuuu uuuu uuuu uuuu
COG1CON0 195h 0000 0000 0000 0000 uuuu uuuu
COG1CON1 196h --00 0000 --00 0000 --uu uuuu
COG1ASD 197h 0000 0000 0000 0000 uuuu uuuu
TABLE 17-4: INITIALIZATION CONDITION FOR REGISTERS (CONTINUED)
Register Address Power-on Reset
MCLR Reset
WDT Reset (Continued)
Brown-out Reset
(1)
Wake-up from Sleep through
Interrupt
Wake-up from Sleep through
WDT Time-out (Continued)
Legend: u = unchanged, x = unknown, – = unimplemented bit, reads as ‘0’, q = value depends on condition.
Note 1: If V
DD goes too low, Power-on Reset will be activated and registers will be affected differently.
2: One or more bits in INTCON and/or PIRx will be affected (to cause wake-up).
3: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h).
4: See Ta b le 17-5 for Reset value for specific condition.
5: If Reset was due to brown-out, then bit 0 = 0. All other Resets will cause bit 0 = u.