Datasheet

ManualsBrandsMICROCHIP TECHNOLOGY ManualsMicrocontrollers, Microprocessors & QuartzesEmbedded microcontroller MSOP 8 8-Bit 8 MHz I/O number 5

Table Of Contents

High-Performance RISC CPU:
Special Microcontroller Features:
Low-Power Features/CMOS Technology:
Peripheral Features:
Table of Contents
Most Current Data Sheet
Errata
Customer Notification System
1.0 General Description
- 1.1 Applications
  - TABLE 1-1: Features and memory of PIC12F519
2.0 PIC12F519 Device Varieties
- 2.1 Quick Turn Programming (QTP) Devices
- 2.2 Serialized Quick Turn ProgrammingSM (SQTPSM) Devices
3.0 Architectural Overview
- TABLE 3-1: PIC12F519 Memory
- FIGURE 3-1: PIC12F519 ARCHITECTURAL Block Diagram
- TABLE 3-2: PIC12F519 Pinout Description
- 3.1 Clocking Scheme/Instruction Cycle
- 3.2 Instruction Flow/Pipelining
  - FIGURE 3-2: Clock/Instruction Cycle
  - EXAMPLE 3-1: Instruction Pipeline Flow
4.0 Memory Organization
- 4.1 Program Memory Organization for the PIC12F519
  - FIGURE 4-1: Memory Map
- 4.2 Data Memory (SRAM and FSRs)
  - 4.2.1 General Purpose Register File
    - FIGURE 4-2: Register File Map
  - 4.2.2 Special Function Registers
    - TABLE 4-1: Special Function Register Summary
- 4.3 STATUS register
  - Register 4-1: STATUS: STATUS Register
- 4.4 OPTION Register
  - Register 4-2: OPTION: OPTION Register
- 4.5 OSCCAL Register
  - Register 4-3: OSCCAL: Oscillator Calibration Register
- 4.6 Program Counter
  - FIGURE 4-3: Loading of PC Branch Instructions
  - 4.6.1 Effects Of Reset
- 4.7 Stack
- 4.8 Indirect Data Addressing: INDF and FSR Registers
  - EXAMPLE 4-1: How to Clear RAM Using Indirect Addressing
  - FIGURE 4-4: Direct/Indirect Addressing
5.0 Flash Data Memory Control
- 5.1 Reading Flash Data Memory
- 5.2 Writing and Erasing Flash Data Memory
  - 5.2.1 Erasing Flash Data Memory
  - 5.2.2 Writing to Flash Data Memory
- 5.3 Write Verify
- 5.4 Code Protection
6.0 I/O Port
- 6.1 GPIO
- 6.2 TRIS Registers
- 6.3 I/O Interfacing
- 6.4 I/O Programming Considerations
  - 6.4.1 Bidirectional I/O Ports
    - EXAMPLE 6-1: Read-modify-write Instructions on an I/O Port
  - 6.4.2 Successive Operations on I/O Ports
    - FIGURE 6-6: Successive I/O OperatioN
7.0 Timer0 Module and TMR0 Register
- FIGURE 7-1: Timer0 Block Diagram
- FIGURE 7-2: TIMER0 Timing: Internal Clock/No Prescale
- FIGURE 7-3: TIMER0 Timing: Internal Clock/Prescale 1:2
- TABLE 7-1: Registers Associated With TIMER0
- 7.1 Using Timer0 with an External Clock
  - 7.1.1 External Clock Synchronization
  - 7.1.2 TIMER0 Increment Delay
    - FIGURE 7-4: TIMER0 Timing with External Clock
- 7.2 Prescaler
  - 7.2.1 Switching Prescaler Assignment
8.0 Special Features Of The CPU
- 8.1 Configuration Bits
  - Register 8-1: CONFIG: Configuration Word Register(1)
- 8.2 Oscillator Configurations
- 8.3 Reset
- 8.4 Power-on Reset (POR)
- 8.5 Device Reset Timer (DRT)
  - TABLE 8-5: DRT (Device Reset Timer Period)
- 8.6 Watchdog Timer (WDT)
  - 8.6.1 WDT Period
  - 8.6.2 WDT Programming Considerations
    - FIGURE 8-11: Watchdog Timer Block Diagram
    - TABLE 8-6: Summary of Register Associated with the Watchdog Timer
- 8.7 Time-out Sequence, Power-down and Wake-up from Sleep Status Bits (TO, PD, GPWUF)
  - TABLE 8-7: TO/PD/(GPWUF) Status After Reset
- 8.8 Power-down Mode (Sleep)
  - 8.8.1 Sleep
  - 8.8.2 Wake-up from Sleep
- 8.9 Program Verification/Code Protection
- 8.10 ID Locations
- 8.11 In-Circuit Serial Programming™
  - FIGURE 8-12: Typical In-Circuit Serial Programming Connection
9.0 Instruction Set Summary
- TABLE 9-1: Opcode Field Descriptions
- FIGURE 9-1: General Format for Instructions
- TABLE 9-2: Instruction Set Summary
10.0 Development Support
- 10.1 MPLAB Integrated Development Environment Software
- 10.2 MPASM Assembler
- 10.3 MPLAB C18 and MPLAB C30 C Compilers
- 10.4 MPLINK Object Linker/ MPLIB Object Librarian
- 10.5 MPLAB ASM30 Assembler, Linker and Librarian
- 10.6 MPLAB SIM Software Simulator
- 10.7 MPLAB ICE 2000 High-Performance In-Circuit Emulator
- 10.8 MPLAB REAL ICE In-Circuit Emulator System
- 10.9 MPLAB ICD 2 In-Circuit Debugger
- 10.10 MPLAB PM3 Device Programmer
- 10.11 PICSTART Plus Development Programmer
- 10.12 PICkit 2 Development Programmer
- 10.13 Demonstration, Development and Evaluation Boards
11.0 Electrical Characteristics
- Absolute Maximum Ratings(†)
  - FIGURE 11-1: PIC12F519 Voltage-Frequency Graph, -40°C £ ta £ +125°C
  - FIGURE 11-2: Maximum Oscillator Frequency Table
- 11.1 DC Characteristics
- 11.2 Timing Parameter Symbology and Load Conditions – PIC12F519
  - FIGURE 11-3: Load Conditions – PIC12F519
  - FIGURE 11-4: External Clock Timing – PIC12F519
- 11.3 AC Characteristics
12.0 DC and AC Characteristics Graphs and Charts
- FIGURE 12-1: Typical Idd vs. Fosc Over Vdd (XT, EXTRC mode)
- FIGURE 12-2: Maximum Idd vs. Fosc Over Vdd (XT, EXTRC mode)
- FIGURE 12-3: Idd vs. Vdd over fosc (LP Mode)
- FIGURE 12-4: Typical Ipd vs. Vdd (Sleep Mode, all Peripherals Disabled)
- FIGURE 12-5: Maximum Ipd vs. Vdd (Sleep Mode, all Peripherals Disabled)
- FIGURE 12-6: Typical WDT Ipd VS. Vdd
- FIGURE 12-7: Maximum WDT Ipd VS. Vdd Over Temperature
- FIGURE 12-8: WDT TIME-OUT VS. Vdd Over Temperature (No Prescaler)
- FIGURE 12-9: Vol VS. Iol Over Temperature (Vdd = 3.0V)
- FIGURE 12-10: Vol VS. Iol Over Temperature (Vdd = 5.0V)
- FIGURE 12-11: Voh VS. Ioh Over Temperature (Vdd = 3.0V)
- FIGURE 12-12: Voh VS. Ioh Over Temperature (Vdd = 5.0V)
- FIGURE 12-13: TTL Input Threshold Vin VS. Vdd
- FIGURE 12-14: Schmitt Trigger Input Threshold Vin VS. Vdd
- FIGURE 12-15: Device Reset Timer (XT and LP) vs. Vdd
13.0 Packaging Information
- 13.1 Package Marking Information
Appendix A: Revision History
INDEX
The Microchip Web Site
Customer Change Notification Service
Customer Support
Reader Response
Product Identification System
Worldwide Sales

PIC12F519

8.7 Time-out Sequence, Power-down

and Wake-up from Sleep Status

Bits (TO

, PD, GPWUF)

The TO, PD and (GPWUF) bits in the STATUS register

can be tested to determine if a Reset condition has

been caused by a power-up condition, a MCLR or

Watchdog Timer (WDT) Reset.

TABLE 8-7: TO/PD/(GPWUF) STATUS

AFTER RESET

8.8 Power-down Mode (Sleep)

A device may be powered down (Sleep) and later

powered up (wake-up from Sleep).

8.8.1 SLEEP

The Power-down mode is entered by executing a

SLEEP instruction.

If enabled, the Watchdog Timer will be cleared but

keeps running, the TO

bit (STATUS<4>) is set, the PD

bit (STATUS<3>) is cleared and the oscillator driver is

turned off. The I/O ports maintain the status they had

before the SLEEP instruction was executed (driving

high, driving low or high-impedance).

For lowest current consumption while powered down,

the T0CKI input should be at V

DD or VSS and the

GP3/MCLR

/VPP pin must be at a logic high level if

MCLR

is enabled.

8.8.2 WAKE-UP FROM SLEEP

The device can wake-up from Sleep through one of the

following events:

5. An external Reset input on GP3/MCLR

/VPP pin,

when configured as MCLR

6. A Watchdog Timer Time-out Reset (if WDT was

enabled).

7. A change on input pin GP0, GP1 and GP3 when

wake-up on change is enabled.

These events cause a device Reset. The TO

, PD and

GPWUF bits can be used to determine the cause of

device Reset. The TO bit is cleared if a WDT time-out

occurred (and caused wake-up). The PD

bit, which is

set on power-up, is cleared when SLEEP is invoked.

The GPWUF bit indicates a change in state while in

Sleep at pins GP0, GP1 and GP3 (since the last file or

bit operation on GPIO port).

The WDT is cleared when the device wakes from

Sleep, regardless of the wake-up source.

GPWUF TO PD Reset Caused By

000WDT wake-up from Sleep

00uWDT time-out (not from

Sleep)

010MCLR

wake-up from Sleep

011Power-up

0uuMCLR

not during Sleep

110Wake-up from Sleep on pin

change

Legend: u = unchanged

Note 1: The TO

, PD and GPWUF bits maintain

their status (u) until a Reset occurs. A

low-pulse on the MCLR

input does not

change the TO

, PD and GPWUF Status

bits.

Note: A Reset generated by a WDT time-out

does not drive the MCLR

pin low.

Note: Caution: Right before entering Sleep,

read the input pins. When in Sleep, wake

up occurs when the values at the pins

change from the state they were in at the

last reading. If a wake-up on change

occurs and the pins are not read before

re-entering Sleep, a wake-up will occur

immediately even if no pins change while

in Sleep mode.