Datasheet

PIC12(L)F1840
DS41441C-page 322  2011-2012 Microchip Technology Inc.
Power-down Base Current (IPD)
(2)
D026A* — 250 — — A 1.8 ADC Current (Note 1, 3)
Conversion in progress
—250 — —
A3.0
D026A* — 280 — — A 2.3 ADC Current
Conversion in progress
VREGPM =
1 (Note 1, 3)
— 280 — — A 3.0
— 280 — — A 5.0
D027 — 3 12 15
A 1.8 Cap Sense, Low Power
CPSRM =
0, CPSRNG = 01
(Note 1)
— 4 15 18 A3.0
D027 — 6.3 13 16 A 2.3 Cap Sense, Low Power
CPSRM =
0, CPSRNG = 01
VREGPM =
1 (Note 1)
— 8.5 18 20 A 3.0
— 12.8 23 25 A 5.0
D027A — 6.0 15 20
A 1.8 Cap Sense, Medium Power
CPSRM =
0, CPSRNG = 10
(Note 1)
— 8.0 18 25 A3.0
D027A — 9.5 20 25 A 2.3 Cap Sense, Medium Power
CPSRM =
0, CPSRNG = 10
VREGPM =
1 (Note 1)
— 13 28 30 A 3.0
— 17 32 35 A 5.0
D027B — 15 35 40
A 1.8 Cap Sense, High Power
CPSRM =
0, CPSRNG = 11
(Note 1)
—39 60 75 A3.0
D027B — 20 40 45 A 2.3 Cap Sense, High Power
CPSRM =
0, CPSRNG = 11
VREGPM =
1 (Note 1)
— 42 68 80 A 3.0
— 49 72 86 A 5.0
D028 — 4.8 15 20
A 1.8 Comparator,
Low Power, CxSP =
0 (Note 1)
— 4.9 17 23 A3.0
D028 — 4.9 16 21 A 2.3 Comparator,
Low Power, CxSP =
0
VREGPM = 1 (Note 1)
— 5.0 17 23 A 3.0
— 5.2 18 24 A 5.0
D028A — 27 50 60
A 1.8 Comparator,
Normal Power, CxSP =
1
(Note 1)
—28 55 70 A3.0
D028A — 27 52 62 A 2.3 Comparator,
Normal Power, CxSP =
1
VREGPM = 1 (Note 1)
— 28 55 65 A 3.0
— 29 57 75 A 5.0
30.3 DC Characteristics: Power-Down Base Current (IPD) (Continued)
PIC12LF1840
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C
 TA  +125°C for extended
PIC12F1840
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C
 TA  +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral
 current can be determined by subtracting the base IDD or IPD current from this limit. Max.
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
SS.
3: ADC clock source is FRC.