PIC12(L)F1840 8-Pin Flash Microcontrollers with XLP Technology High-Performance RISC CPU: • Only 49 Instructions to Learn: - All single-cycle instructions except branches • Operating Speed: - DC – 32 MHz oscillator/clock input - DC – 125 ns instruction cycle • Interrupt Capability with Automatic Context Saving • 16-Level Deep Hardware Stack with Optional Overflow/Underflow Reset • Direct, Indirect and Relative Addressing modes: - Two full 16-bit File Select Registers (FSRs) - FSRs can read program and data
PIC12(L)F1840 Peripheral Features (Continued): • Data Signal Modulator module: - Selectable modulator and carrier sources • SR Latch: - Multiple Set/Reset input options - Emulates 555 Timer applications Note: XLP PIC12(L)F1822 (1) 2K 256 128 6 4 4 1 2/1 1 1 0/1/0 Y PIC12(L)F1840 (2) 4K 256 256 6 4 4 1 2/1 1 1 0/1/0 Y PIC16(L)F1823 (1) 2K 256 128 12 8 8 2 2/1 1 1 1/0/0 Y PIC16(L)F1824 (3) 4K 256 256 12 8 8 2 4/1 1 1 1/1/2 Y PIC16(L)F1825 (4) 8K 256 1024 12 8 8 2 4/1 1 1 1/1/2 Y PIC16(L)F1826 (5) 2K 256 25
PIC12(L)F1840 FIGURE 1: 8-PIN DIAGRAM FOR PIC12(L)F1840 PDIP, SOIC, DFN 1: 1 RA5 2 RA4 3 MCLR/VPP/RA3 4 PIC12(L)F1840 Note VDD 8 VSS 7 RA0/ICSPDAT 6 RA1/ICSPCLK 5 RA2 See Table 1 for the location of all peripheral functions.
PIC12(L)F1840 Table of Contents 1.0 Device Overview .......................................................................................................................................................................... 7 2.0 Enhanced Mid-Range CPU ........................................................................................................................................................ 11 3.0 Memory Organization ................................................................................
PIC12(L)F1840 TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors@microchip.
PIC12(L)F1840 NOTES: DS40001441D-page 6 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 1.0 DEVICE OVERVIEW The PIC12(L)F1840 are described within this data sheet. They are available in 8-pin packages. Figure 1-1 shows a block diagram of the PIC12(L)F1840 devices. Table 1-2 shows the pinout descriptions. Reference Table 1-1 for peripherals available per device.
PIC12(L)F1840 FIGURE 1-1: PIC12(L)F1840 BLOCK DIAGRAM Program Flash Memory CLKR OSC2/CLKOUT OSC1/CLKIN RAM EEPROM Clock Reference Timing Generation PORTA CPU INTRC Oscillator (Figure 2-1) MCLR Note 1: 2: DS40001441D-page 8 SR Latch Timer0 Timer1 ADC 10-Bit DAC Comparators ECCP1 MSSP Modulator EUSART FVR CapSense See applicable chapters for more information on peripherals. See Table 1-1 for peripherals available on specific devices. 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 TABLE 1-2: PIC12(L)F1840 PINOUT DESCRIPTION Name RA0/AN0/CPS0/C1IN+/ DACOUT/TX/CK/SDO/ SS(1)/P1B/MDOUT/ICSPDAT/ ICDDAT RA1/AN1/CPS1/VREF/C1IN0-/ SRI/RX/DT/SCL/SCK/ MDMIN/ICSPCLK/ICDCLK RA2/AN2/CPS2/C1OUT/SRQ/ T0CKI/CCP1/P1A/FLT0/ SDA/SDI/INT/MDCIN1 RA3/SS/T1G(1)/VPP/MCLR Function Input Type RA0 TTL AN0 AN Output Type Description CMOS General purpose I/O. — ADC Channel 0 input. CPS0 AN — Capacitive sensing input 0. C1IN+ AN — Comparator C1 positive input.
PIC12(L)F1840 TABLE 1-2: PIC12(L)F1840 PINOUT DESCRIPTION (CONTINUED) Name Function Input Type RA4/AN3/CPS3/OSC2/ CLKOUT/T1OSO/C1IN1-/CLKR/ SDO(1)/CK(1)/TX(1)/P1B(1)/ T1G/MDCIN2 RA4 TTL Output Type Description CMOS General purpose I/O. AN3 AN — CPS3 AN — ADC Channel 3 input. OSC2 — XTAL CLKOUT — T1OSO XTAL XTAL C1IN1- AN — CLKR — CMOS Clock Reference output. SDO — CMOS SPI data output. CK ST CMOS USART synchronous clock. TX — CMOS USART asynchronous transmit.
PIC12(L)F1840 2.0 ENHANCED MID-RANGE CPU Relative addressing modes are available. Two File Select Registers (FSRs) provide the ability to read program and data memory. This family of devices contain an enhanced mid-range 8-bit CPU core. The CPU has 49 instructions. Interrupt capability includes automatic context saving. The hardware stack is 16 levels deep and has Overflow and Underflow Reset capability.
PIC12(L)F1840 2.1 Automatic Interrupt Context Saving During interrupts, certain registers are automatically saved in shadow registers and restored when returning from the interrupt. This saves stack space and user code. See Section 8.5 “Automatic Context Saving”, for more information. 2.2 16-level Stack with Overflow and Underflow These devices have an external stack memory 15 bits wide and 16 words deep.
PIC12(L)F1840 3.0 MEMORY ORGANIZATION These devices contain the following types of memory: • Program Memory - Configuration Words - Device ID - User ID - Flash Program Memory • Data Memory - Core Registers - Special Function Registers - General Purpose RAM - Common RAM • Data EEPROM memory(1) The following features are associated with access and control of program memory and data memory: • PCL and PCLATH • Stack • Indirect Addressing 3.
PIC12(L)F1840 FIGURE 3-1: PROGRAM MEMORY MAP AND STACK FOR PIC12(L)F1840 PC<14:0> CALL, CALLW RETURN, RETLW Interrupt, RETFIE 15 READING PROGRAM MEMORY AS DATA There are two methods of accessing constants in program memory. The first method is to use tables of RETLW instructions. The second method is to set an FSR to point to the program memory. 3.1.1.1 RETLW Instruction Stack Level 0 Stack Level 1 The RETLW instruction can be used to provide access to tables of constants.
PIC12(L)F1840 3.1.1.2 Indirect Read with FSR The program memory can be accessed as data by setting bit 7 of the FSRxH register and reading the matching INDFx register. The MOVIW instruction will place the lower 8 bits of the addressed word in the W register. Writes to the program memory cannot be performed via the INDF registers. Instructions that access the program memory via the FSR require one extra instruction cycle to complete. Example 3-2 demonstrates accessing the program memory via an FSR.
PIC12(L)F1840 3.2.1.1 STATUS Register The STATUS register, shown in Register 3-1, contains: • the arithmetic status of the ALU • the Reset status The STATUS register can be the destination for any instruction, like any other register. If the STATUS register is the destination for an instruction that affects the Z, DC or C bits, then the write to these three bits is disabled. These bits are set or cleared according to the device logic. Furthermore, the TO and PD bits are not writable.
PIC12(L)F1840 3.3.1 SPECIAL FUNCTION REGISTER The Special Function Registers are registers used by the application to control the desired operation of peripheral functions in the device. The Special Function Registers occupy the 20 bytes after the core registers of every data memory bank (addresses x0Ch/x8Ch through x1Fh/x9Fh). The registers associated with the operation of the peripherals are described in the appropriate peripheral chapter of this data sheet. 3.3.
PIC12(L)F1840 MEMORY MAP, BANKS 0-7 BANK 0 000h BANK 1 080h Core Registers (Table 3-2) 00Bh 00Ch 00Dh 00Eh 00Fh 010h 011h 012h 013h 014h 015h 016h 017h 018h 019h 01Ah 01Bh 01Ch 01Dh 01Eh 01Fh 020h PORTA — — — — PIR1 PIR2 — — TMR0 TMR1L TMR1H T1CON T1GCON TMR2 PR2 T2CON — CPSCON0 CPSCON1 Core Registers (Table 3-2) 08Bh 08Ch 08Dh 08Eh 08Fh 090h 091h 092h 093h 094h 095h 096h 097h 098h 099h 09Ah 09Bh 09Ch 09Dh 09Eh 09Fh 0A0h General Purpose Register 80 Bytes 06Fh 070h TRISA — — — — PIE1 PIE2 — — OPTION_R
2011-2013 Microchip Technology Inc.
PIC12(L)F1840 TABLE 3-4: PIC12(L)F1840 MEMORY MAP, BANK 31 Bank 31 FA0h Unimplemented Read as ‘0’ FE3h FE4h FE5h FE6h FE7h FE8h FE9h FEAh FEBh FECh FEDh FEEh FEFh Legend: STATUS_SHAD WREG_SHAD BSR_SHAD PCLATH_SHAD FSR0L_SHAD FSR0H_SHAD FSR1L_SHAD FSR1H_SHAD — STKPTR TOSL TOSH = Unimplemented data memory locations, read as ‘0’. DS40001441D-page 20 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 3.3.5 CORE FUNCTION REGISTERS SUMMARY The Core Function registers listed in Table 3-5 can be addressed from any Bank.
PIC12(L)F1840 TABLE 3-6: Address SPECIAL FUNCTION REGISTER SUMMARY Name Value on all other Resets Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on POR, BOR — — RA5 RA4 RA3 RA2 RA1 RA0 --xx xxxx --xx xxxx Bank 0 00Ch PORTA 00Dh to 010h — Unimplemented — — 011h PIR1 TMR1GIF ADIF RCIF TXIF SSP1IF CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000 012h PIR2 OSFIF — C1IF EEIF BCL1IF — — — 0-00 0--- 0-00 0--- 013h — Unimplemented — — 014h — Unimplemented —
PIC12(L)F1840 TABLE 3-6: Address SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED) Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 — — LATA5 LATA4 — LATA2 LATA1 LATA0 Value on POR, BOR Value on all other Resets Bank 2 10Ch LATA 10Dh to 110h — Unimplemented --xx -xxx --uu -uuu — 111h CM1CON0 C1ON C1OUT 112h CM1CON1 C1INTP C1INTN C1OE C1POL C1PCH<1:0> — — C1SP C1HYS C1SYNC 0000 -100 0000 -100 — — — C1NCH 0000 ---0 0000 ---0 113h — Unimplemented — — 114h
PIC12(L)F1840 TABLE 3-6: Address SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED) Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 — — WPUA5 WPUA4 WPUA3 WPUA2 WPUA1 WPUA0 Value on POR, BOR Value on all other Resets Bank 4 20Ch WPUA 20Dh to 210h --11 1111 --11 1111 — Unimplemented 211h SSP1BUF Synchronous Serial Port Receive Buffer/Transmit Register xxxx xxxx uuuu uuuu 212h SSP1ADD ADD<7:0> 0000 0000 0000 0000 213h SSP1MSK MSK<7:0> 214h SSP1STAT SMP 215h SSP1CON1 2
PIC12(L)F1840 TABLE 3-6: Address Name SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED) Value on POR, BOR Value on all other Resets Unimplemented — — Unimplemented — — Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Banks 8-30 x0Ch/ x8Ch — x1Fh/ x9Fh — Bank 31 F8Ch — FE3h — FE4h STATUS_ — — — — — Z_SHAD DC_SHAD C_SHAD ---- -xxx ---- -uuu SHAD FE5h WREG_ Working Register Shadow 0000 0000 uuuu uuuu SHAD FE6h BSR_ — — — Bank Select Register Shadow ---x xxxx ---u uuuu SHA
PIC12(L)F1840 3.4 PCL and PCLATH 3.4.2 The Program Counter (PC) is 15 bits wide. The low byte comes from the PCL register, which is a readable and writable register. The high byte (PC<14:8>) is not directly readable or writable and comes from PCLATH. On any Reset, the PC is cleared. Figure 3-3 shows the five situations for the loading of the PC.
PIC12(L)F1840 3.5 Stack 3.5.1 The stack is available through the TOSH, TOSL and STKPTR registers. STKPTR is the current value of the Stack Pointer. TOSH:TOSL register pair points to the TOP of the stack. Both registers are read/writable. TOS is split into TOSH and TOSL due to the 15-bit size of the PC. To access the stack, adjust the value of STKPTR, which will position TOSH:TOSL, then read/write to TOSH:TOSL. STKPTR is 5 bits to allow detection of overflow and underflow.
PIC12(L)F1840 FIGURE 3-5: ACCESSING THE STACK EXAMPLE 2 0x0F 0x0E 0x0D 0x0C 0x0B 0x0A 0x09 This figure shows the stack configuration after the first CALL or a single interrupt. If a RETURN instruction is executed, the return address will be placed in the Program Counter and the Stack Pointer decremented to the empty state (0x1F).
PIC12(L)F1840 FIGURE 3-7: ACCESSING THE STACK EXAMPLE 4 TOSH:TOSL 3.5.
PIC12(L)F1840 FIGURE 3-8: INDIRECT ADDRESSING 0x0000 0x0000 Traditional Data Memory 0x0FFF 0x1000 0x1FFF 0x0FFF Reserved 0x2000 Linear Data Memory 0x29AF 0x29B0 FSR Address Range 0x7FFF 0x8000 Reserved 0x0000 Program Flash Memory 0xFFFF Note: 0x7FFF Not all memory regions are completely implemented. Consult device memory tables for memory limits. DS40001441D-page 30 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 3.6.1 TRADITIONAL DATA MEMORY The traditional data memory is a region from FSR address 0x000 to FSR address 0xFFF. The addresses correspond to the absolute addresses of all SFR, GPR and common registers.
PIC12(L)F1840 3.6.2 3.6.3 LINEAR DATA MEMORY The linear data memory is the region from FSR address 0x2000 to FSR address 0x29AF. This region is a virtual region that points back to the 80-byte blocks of GPR memory in all the banks. Unimplemented memory reads as 0x00. Use of the linear data memory region allows buffers to be larger than 80 bytes because incrementing the FSR beyond one bank will go directly to the GPR memory of the next bank.
PIC12(L)F1840 4.0 DEVICE CONFIGURATION Device configuration consists of Configuration Words, Code Protection and Device ID. 4.1 Configuration Words There are several Configuration Word bits that allow different oscillator and memory protection options. These are implemented as Configuration Word 1 at 8007h and Configuration Word 2 at 8008h. Note: The DEBUG bit in Configuration Word 2 is managed automatically by device development tools including debuggers and programmers.
PIC12(L)F1840 4.
PIC12(L)F1840 REGISTER 4-1: CONFIG1: CONFIGURATION WORD 1 (CONTINUED) bit 4-3 WDTE<1:0>: Watchdog Timer Enable bit 11 = WDT enabled 10 = WDT enabled while running and disabled in Sleep 01 = WDT controlled by the SWDTEN bit in the WDTCON register 00 = WDT disabled bit 2-0 FOSC<2:0>: Oscillator Selection bits 111 = ECH: External Clock, High-Power mode (4-20 MHz): device clock supplied to CLKIN pin 110 = ECM: External Clock, Medium-Power mode (0.
PIC12(L)F1840 REGISTER 4-2: CONFIG2: CONFIGURATION WORD 2 R/P-1 (1) LVP R/P-1 DEBUG (2) U-1 R/P-1 R/P-1 R/P-1 — BORV STVREN PLLEN bit 13 bit 8 U-1 U-1 R-1 U-1 U-1 U-1 — — Reserved — — — R/P-1 R/P-1 WRT<1:0> bit 7 bit 0 Legend: R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘1’ ‘0’ = Bit is cleared ‘1’ = Bit is set -n = Value when blank or after Bulk Erase bit 13 LVP: Low-Voltage Programming Enable bit(1) 1 = Low-voltage programming enabled 0 = Hig
PIC12(L)F1840 4.3 Code Protection Code protection allows the device to be protected from unauthorized access. Program memory protection and data EEPROM protection are controlled independently. Internal access to the program memory and data EEPROM are unaffected by any code protection setting. 4.3.1 PROGRAM MEMORY PROTECTION The entire program memory space is protected from external reads and writes by the CP bit in Configuration Words.
PIC12(L)F1840 4.6 Device ID and Revision ID The memory location 8006h is where the Device ID and Revision ID are stored. The upper nine bits hold the Device ID. The lower five bits hold the Revision ID. See Section 11.5 “User ID, Device ID and Configuration Word Access” for more information on accessing these memory locations. Development tools, such as device programmers and debuggers, may be used to read the Device ID and Revision ID.
PIC12(L)F1840 5.0 OSCILLATOR MODULE (WITH FAIL-SAFE CLOCK MONITOR) 5.1 Overview The oscillator module has a wide variety of clock sources and selection features that allow it to be used in a wide range of applications while maximizing performance and minimizing power consumption. Figure 5-1 illustrates a block diagram of the oscillator module. Clock sources can be supplied from external oscillators, quartz crystal resonators, ceramic resonators and Resistor-Capacitor (RC) circuits.
PIC12(L)F1840 SIMPLIFIED PIC® MCU CLOCK SOURCE BLOCK DIAGRAM FIGURE 5-1: External Oscillator LP, XT, HS, RC, EC OSC2 Sleep 4 x PLL Oscillator Timer1 FOSC<2:0> = 100 T1OSO T1OSCEN Enable Oscillator IRCF<3:0> HFPLL 500 kHz Source 16 MHz (HFINTOSC) Postscaler Internal Oscillator Block 500 kHz (MFINTOSC) 31 kHz Source 31 kHz 31 kHz (LFINTOSC) DS40001441D-page 40 16 MHz 8 MHz 4 MHz 2 MHz 1 MHz 500 kHz 250 kHz 125 kHz 62.5 kHz 31.
PIC12(L)F1840 5.2 Clock Source Types Clock sources can be classified as external or internal. External clock sources rely on external circuitry for the clock source to function. Examples are: oscillator modules (EC mode), quartz crystal resonators or ceramic resonators (LP, XT and HS modes) and Resistor-Capacitor (RC) mode circuits. Internal clock sources are contained within the oscillator module.
PIC12(L)F1840 FIGURE 5-3: QUARTZ CRYSTAL OPERATION (LP, XT OR HS MODE) FIGURE 5-4: CERAMIC RESONATOR OPERATION (XT OR HS MODE) PIC® MCU PIC® MCU OSC1/CLKIN C1 To Internal Logic Quartz Crystal C2 OSC1/CLKIN RS(1) RF(2) Sleep OSC2/CLKOUT Note 1: A series resistor (RS) may be required for quartz crystals with low drive level. 2: The value of RF varies with the Oscillator mode selected (typically between 2 M to 10 M.
PIC12(L)F1840 5.2.1.4 4x PLL The oscillator module contains a 4x PLL that can be used with both external and internal clock sources to provide a system clock source. The input frequency for the 4x PLL must fall within specifications. See the PLL Clock Timing Specifications in Section 30.0 “Electrical Specifications”. Note 1: Quartz crystal characteristics vary according to type, package and manufacturer. The user should consult the manufacturer data sheets for specifications and recommended application.
PIC12(L)F1840 FIGURE 5-6: EXTERNAL RC MODES VDD REXT Internal Clock CEXT VSS FOSC/4 or I/O(1) OSC2/CLKOUT Recommended values: 10 k REXT 100 k, <3V 3 k REXT 100 k, 3-5V CEXT > 20 pF, 2-5V Note 1: Output depends upon CLKOUTEN bit of the Configuration Words. The RC oscillator frequency is a function of the supply voltage, the resistor (REXT) and capacitor (CEXT) values and the operating temperature.
PIC12(L)F1840 5.2.2.1 HFINTOSC The High-Frequency Internal Oscillator (HFINTOSC) is a factory calibrated 16 MHz internal clock source. The frequency of the HFINTOSC can be altered via software using the OSCTUNE register (Register 5-3). The output of the HFINTOSC connects to a postscaler and multiplexer (see Figure 5-1). One of multiple frequencies derived from the HFINTOSC can be selected via software using the IRCF<3:0> bits of the OSCCON register. See Section 5.2.2.
PIC12(L)F1840 5.2.2.5 Internal Oscillator Frequency Selection The system clock speed can be selected via software using the Internal Oscillator Frequency Select bits IRCF<3:0> of the OSCCON register. The output of the 16 MHz HFINTOSC postscaler and LFINTOSC connects to a multiplexer (see Figure 5-1). The Internal Oscillator Frequency Select bits IRCF<3:0> of the OSCCON register select the frequency output of the internal oscillators.
PIC12(L)F1840 5.2.2.7 Internal Oscillator Clock Switch Timing When switching between the HFINTOSC, MFINTOSC and the LFINTOSC, the new oscillator may already be shut down to save power (see Figure 5-7). If this is the case, there is a delay after the IRCF<3:0> bits of the OSCCON register are modified before the frequency selection takes place. The OSCSTAT register will reflect the current active status of the HFINTOSC, MFINTOSC and LFINTOSC oscillators.
PIC12(L)F1840 FIGURE 5-7: HFINTOSC/ MFINTOSC INTERNAL OSCILLATOR SWITCH TIMING LFINTOSC (FSCM and WDT disabled) HFINTOSC/ MFINTOSC Start-up Time 2-cycle Sync Running LFINTOSC 0 IRCF <3:0> 0 System Clock HFINTOSC/ MFINTOSC LFINTOSC (Either FSCM or WDT enabled) HFINTOSC/ MFINTOSC 2-cycle Sync Running LFINTOSC 0 IRCF <3:0> 0 System Clock LFINTOSC HFINTOSC/MFINTOSC LFINTOSC turns off unless WDT or FSCM is enabled LFINTOSC Start-up Time 2-cycle Sync Running HFINTOSC/ MFINTOSC
PIC12(L)F1840 5.3 Clock Switching 5.3.3 TIMER1 OSCILLATOR The system clock source can be switched between external and internal clock sources via software using the System Clock Select (SCS) bits of the OSCCON register. The following clock sources can be selected using the SCS bits: The Timer1 oscillator is a separate crystal oscillator associated with the Timer1 peripheral. It is optimized for timekeeping operations with a 32.768 kHz crystal connected between the T1OSO and T1OSI device pins.
PIC12(L)F1840 5.4 Two-Speed Clock Start-up Mode 5.4.1 Two-Speed Start-up mode provides additional power savings by minimizing the latency between external oscillator start-up and code execution. In applications that make heavy use of the Sleep mode, Two-Speed Start-up will remove the external oscillator start-up time from the time spent awake and can reduce the overall power consumption of the device.
PIC12(L)F1840 5.4.2 1. 2. 3. 4. 5. 6. 7. TWO-SPEED START-UP SEQUENCE 5.4.3 Wake-up from Power-on Reset or Sleep. Instructions begin execution by the internal oscillator at the frequency set in the IRCF<3:0> bits of the OSCCON register. OST enabled to count 1024 clock cycles. OST timed out, wait for falling edge of the internal oscillator. OSTS is set. System clock held low until the next falling edge of new clock (LP, XT or HS mode). System clock is switched to external clock source.
PIC12(L)F1840 5.5 Fail-Safe Clock Monitor 5.5.3 The Fail-Safe Clock Monitor (FSCM) allows the device to continue operating should the external oscillator fail. The FSCM can detect oscillator failure any time after the Oscillator Start-up Timer (OST) has expired. The FSCM is enabled by setting the FCMEN bit in the Configuration Words. The FSCM is applicable to all external Oscillator modes (LP, XT, HS, EC, Timer1 Oscillator and RC).
PIC12(L)F1840 FIGURE 5-10: FSCM TIMING DIAGRAM Sample Clock Oscillator Failure System Clock Output Clock Monitor Output (Q) Failure Detected OSCFIF Test Note: Test Test The system clock is normally at a much higher frequency than the sample clock. The relative frequencies in this example have been chosen for clarity. 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 5.
PIC12(L)F1840 REGISTER 5-2: OSCSTAT: OSCILLATOR STATUS REGISTER R-1/q R-0/q R-q/q R-0/q R-0/q R-q/q R-0/0 R-0/q T1OSCR PLLR OSTS HFIOFR HFIOFL MFIOFR LFIOFR HFIOFS bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared q = Conditional bit 7 T1OSCR: Timer1 Oscillator Ready bit If T1OSCEN = 1: 1 = Timer1 oscillator i
PIC12(L)F1840 REGISTER 5-3: OSCTUNE: OSCILLATOR TUNING REGISTER U-0 U-0 — — R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 TUN<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 TUN<5:0>: Frequency Tuning bits 100000 = Minimum frequency • • • 111111 000000 = Oscillat
PIC12(L)F1840 6.0 REFERENCE CLOCK MODULE 6.3 Conflicts with the CLKR Pin The reference clock module provides the ability to send a divided clock to the clock output pin of the device (CLKR) and provide a secondary internal clock source to the modulator module. This module is available in all oscillator configurations and allows the user to select a greater range of clock submultiples to drive external devices in the application.
PIC12(L)F1840 6.
PIC12(L)F1840 TABLE 6-1: SUMMARY OF REGISTERS ASSOCIATED WITH REFERENCE CLOCK SOURCES Name CLKRCON Legend: Bit 7 Bit 6 Bit 5 CLKREN CLKROE CLKRSLR CONFIG1 Legend: Bit 3 CLKRDC<1:0> Bit 2 Bit 1 Bit 0 Register on Page 58 CLKRDIV<2:0> — = unimplemented locations read as ‘0’. Shaded cells are not used by reference clock sources.
PIC12(L)F1840 NOTES: DS40001441D-page 60 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 7.0 RESETS There are multiple ways to reset this device: • • • • • • • • Power-On Reset (POR) Brown-Out Reset (BOR) MCLR Reset WDT Reset RESET instruction Stack Overflow Stack Underflow Programming mode exit To allow VDD to stabilize, an optional power-up timer can be enabled to extend the Reset time after a BOR or POR event. A simplified block diagram of the On-Chip Reset Circuit is shown in Figure 7-1.
PIC12(L)F1840 7.1 Power-On Reset (POR) 7.2 Brown-Out Reset (BOR) The POR circuit holds the device in Reset until VDD has reached an acceptable level for minimum operation. Slow rising VDD, fast operating speeds or analog performance may require greater than minimum VDD. The PWRT, BOR or MCLR features can be used to extend the start-up period until all device operation conditions have been met. The BOR circuit holds the device in Reset when VDD reaches a selectable minimum level.
PIC12(L)F1840 FIGURE 7-2: BROWN-OUT SITUATIONS VDD VBOR Internal Reset TPWRT(1) VDD VBOR Internal Reset < TPWRT TPWRT(1) VDD VBOR Internal Reset Note 1: 7.3 TPWRT(1) TPWRT delay only if PWRTE bit is programmed to ‘0’.
PIC12(L)F1840 7.4 MCLR 7.9 Power-Up Timer The MCLR is an optional external input that can reset the device. The MCLR function is controlled by the MCLRE bit of Configuration Words and the LVP bit of Configuration Words (Table 7-2). The Power-up Timer optionally delays device execution after a BOR or POR event. This timer is typically used to allow VDD to stabilize before allowing the device to start running. TABLE 7-2: The Power-up Timer is controlled by the PWRTE bit of Configuration Words.
PIC12(L)F1840 FIGURE 7-3: RESET START-UP SEQUENCE VDD Internal POR TPWRT Power-Up Timer MCLR TMCLR Internal RESET Oscillator Modes External Crystal TOST Oscillator Start-Up Timer Oscillator FOSC Internal Oscillator Oscillator FOSC External Clock (EC) CLKIN FOSC 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 7.11 Determining the Cause of a Reset Upon any Reset, multiple bits in the STATUS and PCON register are updated to indicate the cause of the Reset. Table 7-3 and Table 7-4 show the Reset conditions of these registers.
PIC12(L)F1840 7.12 Power Control (PCON) Register The Power Control (PCON) register contains flag bits to differentiate between a: • • • • • • Power-on Reset (POR) Brown-out Reset (BOR) Reset Instruction Reset (RI) Stack Overflow Reset (STKOVF) Stack Underflow Reset (STKUNF) MCLR Reset (RMCLR) The PCON register bits are shown in Register 7-2. 7.
PIC12(L)F1840 TABLE 7-5: SUMMARY OF REGISTERS ASSOCIATED WITH RESETS Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register on Page BORCON SBOREN BORFS — — — — — BORRDY 63 PCON STKOVF STKUNF — — RMCLR RI POR BOR 67 STATUS — — — TO PD Z DC C 16 WDTCON — — SWDTEN 85 WDTPS<4:0> Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by Resets. Note 1: Other (non Power-up) Resets include MCLR Reset and Watchdog Timer Reset during normal operation.
PIC12(L)F1840 8.0 INTERRUPTS The interrupt feature allows certain events to preempt normal program flow. Firmware is used to determine the source of the interrupt and act accordingly. Some interrupts can be configured to wake the MCU from Sleep mode. This chapter contains the following information for Interrupts: • • • • • Operation Interrupt Latency Interrupts During Sleep INT Pin Automatic Context Saving Many peripherals produce interrupts. Refer to the corresponding chapters for details.
PIC12(L)F1840 8.1 Operation Interrupts are disabled upon any device Reset. They are enabled by setting the following bits: • GIE bit of the INTCON register • Interrupt Enable bit(s) for the specific interrupt event(s) • PEIE bit of the INTCON register (if the Interrupt Enable bit of the interrupt event is contained in the PIEx register) 8.2 Interrupt Latency Interrupt latency is defined as the time from when the interrupt event occurs to the time code execution at the interrupt vector begins.
PIC12(L)F1840 FIGURE 8-2: INTERRUPT LATENCY OSC1 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 CLKOUT Interrupt Sampled during Q1 Interrupt GIE PC Execute PC-1 PC 1 Cycle Instruction at PC PC+1 0004h 0005h NOP NOP Inst(0004h) PC+1/FSR ADDR New PC/ PC+1 0004h 0005h Inst(PC) NOP NOP Inst(0004h) FSR ADDR PC+1 PC+2 0004h 0005h INST(PC) NOP NOP NOP Inst(0004h) Inst(0005h) FSR ADDR PC+1 0004h 0005h INST(PC) NOP NOP Inst(00
PIC12(L)F1840 FIGURE 8-3: INT PIN INTERRUPT TIMING Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 CLKOUT (3) (4) INT pin (1) (1) INTF Interrupt Latency (2) (5) GIE INSTRUCTION FLOW PC Instruction Fetched Instruction Executed Note 1: PC Inst (PC) Inst (PC – 1) PC + 1 Inst (PC + 1) Inst (PC) PC + 1 — Dummy Cycle 0004h 0005h Inst (0004h) Inst (0005h) Dummy Cycle Inst (0004h) INTF flag is sampled here (every Q1).
PIC12(L)F1840 8.3 Interrupts During Sleep Some interrupts can be used to wake from Sleep. To wake from Sleep, the peripheral must be able to operate without the system clock. The interrupt source must have the appropriate Interrupt Enable bit(s) set prior to entering Sleep. On waking from Sleep, if the GIE bit is also set, the processor will branch to the interrupt vector. Otherwise, the processor will continue executing instructions after the SLEEP instruction.
PIC12(L)F1840 8.
PIC12(L)F1840 REGISTER 8-2: PIE1: PERIPHERAL INTERRUPT ENABLE REGISTER 1 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 TMR1GIE ADIE RCIE TXIE SSP1IE CCP1IE TMR2IE TMR1IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 TMR1GIE: Timer1 Gate Interrupt Enable bit 1 = Enables the Timer1 Gat
PIC12(L)F1840 REGISTER 8-3: PIE2: PERIPHERAL INTERRUPT ENABLE REGISTER 2 R/W-0/0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 U-0 U-0 U-0 OSFIE — C1IE EEIE BCL1IE — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 OSFIE: Oscillator Fail Interrupt Enable bit 1 = Enables the Oscillator Fail interrupt 0 = Disables the O
PIC12(L)F1840 REGISTER 8-4: PIR1: PERIPHERAL INTERRUPT REQUEST REGISTER 1 R/W-0/0 R/W-0/0 R-0/0 R-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 TMR1GIF ADIF RCIF TXIF SSP1IF CCP1IF TMR2IF TMR1IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 TMR1GIF: Timer1 Gate Interrupt Flag bit 1 = Interrupt is pending 0 = In
PIC12(L)F1840 REGISTER 8-5: PIR2: PERIPHERAL INTERRUPT REQUEST REGISTER 2 R/W-0/0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 U-0 U-0 U-0 OSFIF — C1IF EEIF BCL1IF — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 OSFIF: Oscillator Fail Interrupt Flag bit 1 = Interrupt is pending 0 = Interrupt is not pending bit 6
PIC12(L)F1840 9.0 POWER-DOWN MODE (SLEEP) 9.1 Wake-up from Sleep The Power-down mode is entered by executing a SLEEP instruction. The device can wake-up from Sleep through one of the following events: Upon entering Sleep mode, the following conditions exist: 1. 2. 3. 4. 5. 6. 1. WDT will be cleared but keeps running, if enabled for operation during Sleep. 2. PD bit of the STATUS register is cleared. 3. TO bit of the STATUS register is set. 4. CPU clock is disabled. 5.
PIC12(L)F1840 9.1.1 WAKE-UP USING INTERRUPTS When global interrupts are disabled (GIE cleared) and any interrupt source has both its interrupt enable bit and interrupt flag bit set, one of the following will occur: • If the interrupt occurs before the execution of a SLEEP instruction - SLEEP instruction will execute as a NOP. - WDT and WDT prescaler will not be cleared - TO bit of the STATUS register will not be set - PD bit of the STATUS register will not be cleared.
PIC12(L)F1840 9.2 Low-Power Sleep Mode The PIC12F1840 device contains an internal Low Dropout (LDO) voltage regulator, which allows the device I/O pins to operate at voltages up to 5.5V while the internal device logic operates at a lower voltage. The LDO and its associated reference circuitry must remain active when the device is in Sleep mode. The PIC12F1840 allows the user to optimize the operating current in Sleep, depending on the application requirements.
PIC12(L)F1840 9.
PIC12(L)F1840 10.0 WATCHDOG TIMER (WDT) The Watchdog Timer is a system timer that generates a Reset if the firmware does not issue a CLRWDT instruction within the time-out period. The Watchdog Timer is typically used to recover the system from unexpected events.
PIC12(L)F1840 10.1 Independent Clock Source 10.3 The WDT derives its time base from the 31 kHz LFINTOSC internal oscillator. Time intervals in this chapter are based on a nominal interval of 1 ms. See Section 30.0 “Electrical Specifications” for the LFINTOSC tolerances. 10.2 The Watchdog Timer module has four operating modes controlled by the WDTE<1:0> bits in Configuration Words. See Table 10-1. 10.2.1 WDT IS ALWAYS ON When the WDTE bits of Configuration Words are set to ‘11’, the WDT is always on.
PIC12(L)F1840 10.
PIC12(L)F1840 TABLE 10-3: Name SUMMARY OF REGISTERS ASSOCIATED WITH WATCHDOG TIMER Bit 7 Bit 6 Bit 5 STATUS — — — WDTCON — — OSCCON Legend: SPLLEN CONFIG1 Legend: Bit 3 IRCF<3:0> Bit 2 Bit 1 — TO PD Bit 0 SCS<1:0> Z DC WDTPS<4:0> Register on Page 54 C 16 SWDTEN 85 x = unknown, u = unchanged, – = unimplemented locations read as ‘0’. Shaded cells are not used by Watchdog Timer.
PIC12(L)F1840 11.0 DATA EEPROM AND FLASH PROGRAM MEMORY CONTROL The data EEPROM and Flash program memory are readable and writable during normal operation (full VDD range). These memories are not directly mapped in the register file space. Instead, they are indirectly addressed through the Special Function Registers (SFRs).
PIC12(L)F1840 11.2 Using the Data EEPROM The data EEPROM is a high-endurance, byte addressable array that has been optimized for the storage of frequently changing information (e.g., program variables or other data that are updated often). When variables in one section change frequently, while variables in another section do not change, it is possible to exceed the total number of write cycles to the EEPROM without exceeding the total number of write cycles to a single byte. Refer to Section 30.
PIC12(L)F1840 Required Sequence EXAMPLE 11-2: DATA EEPROM WRITE BANKSEL MOVLW MOVWF MOVLW MOVWF BCF BCF BSF EEADRL DATA_EE_ADDR EEADRL DATA_EE_DATA EEDATL EECON1, CFGS EECON1, EEPGD EECON1, WREN ; ; ;Data Memory Address to write ; ;Data Memory Value to write ;Deselect Configuration space ;Point to DATA memory ;Enable writes BCF MOVLW MOVWF MOVLW MOVWF BSF BSF BCF BTFSC GOTO INTCON, 55h EECON2 0AAh EECON2 EECON1, INTCON, EECON1, EECON1, $-2 ;Disable INTs.
PIC12(L)F1840 11.3 Flash Program Memory Overview It is important to understand the Flash program memory structure for erase and programming operations. Flash program memory is arranged in rows. A row consists of a fixed number of 14-bit program memory words. A row is the minimum block size that can be erased by user software.
PIC12(L)F1840 EXAMPLE 11-3: FLASH PROGRAM MEMORY READ * This code block will read 1 word of program * memory at the memory address: PROG_ADDR_HI: PROG_ADDR_LO * data will be returned in the variables; * PROG_DATA_HI, PROG_DATA_LO BANKSEL MOVLW MOVWF MOVLW MOVWL EEADRL PROG_ADDR_LO EEADRL PROG_ADDR_HI EEADRH ; Select Bank for EEPROM registers ; ; Store LSB of address ; ; Store MSB of address BCF BSF BCF BSF NOP NOP BSF EECON1,CFGS EECON1,EEPGD INTCON,GIE EECON1,RD INTCON,GIE ; ; ; ; ; ; ; Do not sel
PIC12(L)F1840 11.3.2 ERASING FLASH PROGRAM MEMORY While executing code, program memory can only be erased by rows. To erase a row: 1. 2. 3. 4. 5. 6. Load the EEADRH:EEADRL register pair with the address of new row to be erased. Clear the CFGS bit of the EECON1 register. Set the EEPGD, FREE and WREN bits of the EECON1 register. Write 55h, then AAh, to EECON2 (Flash programming unlock sequence). Set control bit WR of the EECON1 register to begin the erase operation.
PIC12(L)F1840 After the “BSF EECON1,WR” instruction, the processor requires two cycles to set up the write operation. The user must place two NOP instructions after the WR bit is set. The processor will halt internal operations for the typical 2 ms, only during the cycle in which the write takes place (i.e., the last word of the block write). This is not Sleep mode as the clocks and peripherals will FIGURE 11-2: continue to run. The processor does not stall when LWLO = 1, loading the write latches.
PIC12(L)F1840 EXAMPLE 11-5: ; ; ; ; ; ; ; WRITING TO FLASH PROGRAM MEMORY This write routine assumes the following: 1. The 64 bytes of data are loaded, starting at the address in DATA_ADDR 2. Each word of data to be written is made up of two adjacent bytes in DATA_ADDR, stored in little endian format 3. A valid starting address (the least significant bits = 00000) is loaded in ADDRH:ADDRL 4.
PIC12(L)F1840 11.4 Modifying Flash Program Memory When modifying existing data in a program memory row, and data within that row must be preserved, it must first be read and saved in a RAM image. Program memory is modified using the following steps: 1. 2. 3. 4. 5. 6. 7. 8. Load the starting address of the row to be modified. Read the existing data from the row into a RAM image. Modify the RAM image to contain the new data to be written into program memory.
PIC12(L)F1840 11.6 Write Verify Depending on the application, good programming practice may dictate that the value written to the data EEPROM or program memory should be verified (see Example 11-6) to the desired value to be written. Example 11-6 shows how to verify a write to EEPROM.
PIC12(L)F1840 11.
PIC12(L)F1840 REGISTER 11-5: EECON1: EEPROM CONTROL 1 REGISTER R/W-0/0 R/W-0/0 R/W-0/0 R/W/HC-0/0 R/W-x/q R/W-0/0 R/S/HC-0/0 R/S/HC-0/0 EEPGD CFGS LWLO FREE WRERR WREN WR RD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ S = Bit can only be set x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared HC = Bit is cleared by hardware bit 7 EEPGD: Flash Program/Data EEPROM Memory Select
PIC12(L)F1840 REGISTER 11-6: W-0/0 EECON2: EEPROM CONTROL 2 REGISTER W-0/0 W-0/0 W-0/0 W-0/0 W-0/0 W-0/0 W-0/0 EEPROM Control Register 2 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ S = Bit can only be set x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-0 Data EEPROM Unlock Pattern bits To unlock writes, a 55h must be written first, followed by an AAh, before setting the WR bit
PIC12(L)F1840 NOTES: DS40001441D-page 100 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 12.0 I/O PORTS 12.1 In general, when a peripheral is enabled, that pin may not be used as a general purpose I/O pin. The port has three registers for its operation. These registers are: • TRISA register (data direction register) • PORTA register (reads the levels on the pins of the device) • LATA register (output latch) Alternate Pin Function The Alternate Pin Function Control (APFCON) register is used to steer specific peripheral input and output functions between different pins.
PIC12(L)F1840 REGISTER 12-1: APFCON: ALTERNATE PIN FUNCTION CONTROL REGISTER R/W-0/0 R/W-0/0 R/W-0/0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 RXDTSEL SDOSEL SSSEL — T1GSEL TXCKSEL P1BSEL CCP1SEL bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 RXDTSEL: Pin Selection bit 1 = RX/DT function is on RA5 0 = RX/DT
PIC12(L)F1840 12.2 PORTA Registers 12.2.1 DATA REGISTER PORTA is a 6-bit wide, bidirectional port. The corresponding data direction register is TRISA (Register 12-3). Setting a TRISA bit (= 1) will make the corresponding PORTA pin an input (i.e., disable the output driver). Clearing a TRISA bit (= 0) will make the corresponding PORTA pin an output (i.e., enables output driver and puts the contents of the output latch on the selected pin).
PIC12(L)F1840 12.2.4 PORTA FUNCTIONS AND OUTPUT PRIORITIES Each PORTA pin is multiplexed with other functions. The pins, their combined functions and their output priorities are shown in Table 12-1. When multiple outputs are enabled, the actual pin control goes to the peripheral with the highest priority. Analog input functions, such as ADC, comparator and CapSense inputs, are not shown in the priority lists. These inputs are active when the I/O pin is set for Analog mode using the ANSELx registers.
PIC12(L)F1840 12.
PIC12(L)F1840 REGISTER 12-4: LATA: PORTA DATA LATCH REGISTER U-0 U-0 R/W-x/u R/W-x/u U-0 R/W-x/u R/W-x/u R/W-x/u — — LATA5 LATA4 — LATA2 LATA1 LATA0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 LATA<5:4>: RA<5:4> Output Latch Value bits(1) bit 3 Unimplemented:
PIC12(L)F1840 REGISTER 12-6: WPUA: WEAK PULL-UP PORTA REGISTER U-0 U-0 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 — — WPUA5 WPUA4 WPUA3 WPUA2 WPUA1 WPUA0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 WPUA<5:0>: Weak Pull-up Register bits 1 = Pull-up enabled
PIC12(L)F1840 NOTES: DS40001441D-page 108 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 13.0 INTERRUPT-ON-CHANGE The PORTA pins can be configured to operate as Interrupt-On-Change (IOC) pins. An interrupt can be generated by detecting a signal that has either a rising edge or a falling edge. Any individual PORTA pin, or combination of PORTA pins, can be configured to generate an interrupt.
PIC12(L)F1840 FIGURE 13-1: INTERRUPT-ON-CHANGE BLOCK DIAGRAM IOCANx D Q4Q1 Q CK Edge Detect R RAx IOCAPx D Data Bus = 0 or 1 Q write IOCAFx CK D S Q To Data Bus IOCAFx CK IOCIE R Q2 From all other IOCAFx individual Pin Detectors Q1 Q2 Q3 Q4 Q4Q1 DS40001441D-page 110 Q1 Q1 Q2 Q2 Q3 Q4 Q4Q1 IOC Interrupt to CPU core Q3 Q4 Q4 Q4Q1 Q4Q1 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 13.
PIC12(L)F1840 TABLE 13-1: Name SUMMARY OF REGISTERS ASSOCIATED WITH INTERRUPT-ON-CHANGE Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register on Page ANSELA — — — ANSA4 — ANSA2 ANSA1 ANSA0 106 INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 74 IOCAF — — IOCAF5 IOCAF4 IOCAF3 IOCAF2 IOCAF1 IOCAF0 111 IOCAN — — IOCAN5 IOCAN4 IOCAN3 IOCAN2 IOCAN1 IOCAN0 111 IOCAP — — IOCAP5 IOCAP4 IOCAP3 IOCAP2 IOCAP1 IOCAP0 111 TRISA — — TRISA5 TRISA4 TRIS
PIC12(L)F1840 14.0 FIXED VOLTAGE REFERENCE (FVR) The Fixed Voltage Reference, or FVR, is a stable voltage reference, independent of VDD, with 1.024V, 2.048V or 4.096V selectable output levels. The output of the FVR can be configured to supply a reference voltage to the following: • • • • • ADC input channel ADC positive reference Comparator positive input Digital-to-Analog Converter (DAC) Capacitive Sensing (CPS) module The FVR can be enabled by setting the FVREN bit of the FVRCON register. 14.
PIC12(L)F1840 TABLE 14-1: PERIPHERALS REQUIRING THE FIXED VOLTAGE REFERENCE (FVR) Peripheral HFINTOSC BOR LDO Conditions Description FOSC<2:0> = 100 and IRCF<3:0> = 000x INTOSC is active and device is not in Sleep. BOREN<1:0> = 11 BOR always enabled. BOREN<1:0> = 10 and BORFS = 1 BOR disabled in Sleep mode, BOR Fast Start enabled. BOREN<1:0> = 01 and BORFS = 1 BOR under software control, BOR Fast Start enabled.
PIC12(L)F1840 14.
PIC12(L)F1840 NOTES: DS40001441D-page 116 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 15.0 TEMPERATURE INDICATOR MODULE FIGURE 15-1: This family of devices is equipped with a temperature circuit designed to measure the operating temperature of the silicon die. The circuit's range of operating temperature falls between -40°C and +85°C. The output is a voltage that is proportional to the device temperature. The output of the temperature indicator is internally connected to the device ADC.
PIC12(L)F1840 15.3.1 ACQUISITION TIME To ensure accurate temperature measurements, the user must wait at least 200 s after the ADC input multiplexer is connected to the temperature indicator output before the conversion is performed. In addition, the user must wait 200 s between sequential conversions of the temperature indicator output.
PIC12(L)F1840 16.0 ANALOG-TO-DIGITAL CONVERTER (ADC) MODULE The ADC can generate an interrupt upon completion of a conversion. This interrupt can be used to wake-up the device from Sleep. The Analog-to-Digital Converter (ADC) allows conversion of an analog input signal to a 10-bit binary representation of that signal. This device uses analog inputs, which are multiplexed into a single sample and hold circuit. The output of the sample and hold is connected to the input of the converter.
PIC12(L)F1840 16.1 ADC Configuration When configuring and using the ADC the following functions must be considered: • • • • • • Port configuration Channel selection ADC voltage reference selection ADC conversion clock source Interrupt control Result formatting 16.1.1 PORT CONFIGURATION The ADC can be used to convert both analog and digital signals. When converting analog signals, the I/O pin should be configured for analog by setting the associated TRIS and ANSEL bits. Refer to Section 12.
PIC12(L)F1840 TABLE 16-1: ADC CLOCK PERIOD (TAD) VS. DEVICE OPERATING FREQUENCIES ADC Clock Period (TAD) Device Frequency (FOSC) ADC Clock Source ADCS<2:0> 32 MHz 20 MHz 16 MHz 8 MHz 4 MHz 1 MHz Fosc/2 000 62.5ns(2) 100 ns(2) 125 ns(2) 250 ns(2) 500 ns(2) 2.0 s Fosc/4 100 125 ns (2) (2) (2) (2) Fosc/8 001 0.5 s(2) 400 ns(2) 0.5 s(2) Fosc/16 101 800 ns 800 ns 1.0 s Fosc/32 1.0 s 010 200 ns 1.6 s 250 ns 2.0 s Fosc/64 110 2.0 s 3.2 s 4.0 s FRC x11 1.
PIC12(L)F1840 16.1.5 INTERRUPTS 16.1.6 The ADC module allows for the ability to generate an interrupt upon completion of an Analog-to-Digital conversion. The ADC Interrupt Flag is the ADIF bit in the PIR1 register. The ADC Interrupt Enable is the ADIE bit in the PIE1 register. The ADIF bit must be cleared in software. RESULT FORMATTING The 10-bit ADC conversion result can be supplied in two formats, left justified or right justified. The ADFM bit of the ADCON1 register controls the output format.
PIC12(L)F1840 16.2 16.2.1 ADC Operation STARTING A CONVERSION To enable the ADC module, the ADON bit of the ADCON0 register must be set to a ‘1’. Setting the GO/ DONE bit of the ADCON0 register to a ‘1’ will start the Analog-to-Digital conversion. Note: 16.2.2 The GO/DONE bit should not be set in the same instruction that turns on the ADC. Refer to Section 16.2.6 “ADC Conversion Procedure”.
PIC12(L)F1840 16.2.6 ADC CONVERSION PROCEDURE This is an example procedure for using the ADC to perform an Analog-to-Digital conversion: 1. 2. 3. 4. 5. 6. 7. 8.
PIC12(L)F1840 16.
PIC12(L)F1840 REGISTER 16-2: R/W-0/0 ADCON1: ADC CONTROL REGISTER 1 R/W-0/0 ADFM R/W-0/0 R/W-0/0 ADCS<2:0> U-0 U-0 — — R/W-0/0 R/W-0/0 ADPREF<1:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 ADFM: ADC Result Format Select bit 1 = Right justified.
PIC12(L)F1840 REGISTER 16-3: R/W-x/u ADRESH: ADC RESULT REGISTER HIGH (ADRESH) ADFM = 0 R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u ADRES<9:2> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-0 ADRES<9:2>: ADC Result Register bits Upper 8 bits of 10-bit conversion result REGISTER 16-4: R/W-x/u ADRE
PIC12(L)F1840 REGISTER 16-5: ADRESH: ADC RESULT REGISTER HIGH (ADRESH) ADFM = 1 R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u — — — — — — R/W-x/u R/W-x/u ADRES<9:8> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-2 Reserved: Do not use.
PIC12(L)F1840 16.4 ADC Acquisition Requirements For the ADC to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the input channel voltage level. The Analog Input model is shown in Figure 16-4. The source impedance (RS) and the internal sampling switch (RSS) impedance directly affect the time required to charge the capacitor CHOLD. The sampling switch (RSS) impedance varies over the device voltage (VDD), refer to Figure 16-4.
PIC12(L)F1840 FIGURE 16-4: ANALOG INPUT MODEL VDD Analog Input pin Rs VT 0.6V CPIN 5 pF VA RIC 1k Sampling Switch SS Rss I LEAKAGE(1) VT 0.
PIC12(L)F1840 TABLE 16-3: Name SUMMARY OF REGISTERS ASSOCIATED WITH ADC Bit 7 ADCON0 — ADCON1 ADFM Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 — — CHS<4:0> ADCS<2:0> Bit 1 Bit 0 GO/DONE ADON ADPREF<1:0> Register on Page 125 126 ADRESH ADC Result Register High 127, 128 ADRESL ADC Result Register Low 127, 128 ANSELA — — P1M<1:0> CCP1CON — ANSA4 — DC1B<1:0> — ANSA2 ANSA1 ANSA0 CCP1M<3:0> DACPSS<1:0> — 106 197 — DACCON0 DACEN DACLPS DACOE DACCON1 — — — FVRCON FVREN FVRRDY
PIC12(L)F1840 NOTES: DS40001441D-page 132 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 17.0 DIGITAL-TO-ANALOG CONVERTER (DAC) MODULE The Digital-to-Analog Converter supplies a variable voltage reference, ratiometric with the input source, with 32 selectable output levels. The input of the DAC can be connected to: 17.1 Output Voltage Selection The DAC has 32 voltage level ranges. The 32 levels are set with the DACR<4:0> bits of the DACCON1 register.
PIC12(L)F1840 FIGURE 17-1: DIGITAL-TO-ANALOG CONVERTER BLOCK DIAGRAM Digital-to-Analog Converter (DAC) FVR BUFFER2 VSOURCE+ VDD DACR<4:0> 5 VREF R R DACPSS<1:0> 2 R DACEN DACLPS R 32 Steps R 32-to-1 MUX R DAC_output R (To Comparator, CPS and ADC Modules) DACOUT R DACOE VSOURCE- VSS FIGURE 17-2: VOLTAGE REFERENCE OUTPUT BUFFER EXAMPLE PIC® MCU DAC Module R Voltage Reference Output Impedance DS40001441D-page 134 DACOUT + – Buffered DAC Output 2011-2013 Microchip Technology Inc
PIC12(L)F1840 17.4 Low-Power Voltage State This is also the method used to output the voltage level from the FVR to an output pin. See Section 17.5 “Operation During Sleep” for more information. In order for the DAC module to consume the least amount of power, one of the two voltage reference input sources to the resistor ladder must be disconnected. Either the positive voltage source, (VSOURCE+), or the negative voltage source, (VSOURCE-) can be disabled.
PIC12(L)F1840 17.
PIC12(L)F1840 18.0 SR LATCH The module consists of a single SR latch with multiple Set and Reset inputs as well as separate latch outputs. The SR latch module includes the following features: • • • • Programmable input selection SR latch output is available externally Separate Q and Q outputs Firmware Set and Reset The SR latch can be used in a variety of analog applications, including oscillator circuits, one-shot circuit, hysteretic controllers, and analog timing applications. 18.1 18.
PIC12(L)F1840 FIGURE 18-1: SR LATCH SIMPLIFIED BLOCK DIAGRAM SRPS SRLEN SRQEN Pulse Gen(2) SRI S SRSPE Q SRCLK SRQ SRSCKE sync_C1OUT(3) SRSC1E SR Latch(1) SRPR Pulse Gen(2) SRI R SRRPE Q SRNQ SRCLK SRRCKE SRLEN sync_C1OUT(3) SRRC1E SRNQEN Note 1: 2: 3: TABLE 18-1: If R = 1 and S = 1 simultaneously, Q = 0, Q = 1 Pulse generator causes a 1 Q-state pulse width. Name denotes the connection point at the comparator output.
PIC12(L)F1840 18.
PIC12(L)F1840 REGISTER 18-2: SRCON1: SR LATCH CONTROL 1 REGISTER R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 SRSPE SRSCKE Reserved SRSC1E SRRPE SRRCKE Reserved SRRC1E bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 SRSPE: SR Latch Peripheral Set Enable bit 1 = SR latch is set when t
PIC12(L)F1840 19.0 COMPARATOR MODULE Comparators are used to interface analog circuits to a digital circuit by comparing two analog voltages and providing a digital indication of their relative magnitudes. Comparators are very useful mixed signal building blocks because they provide analog functionality independent of program execution.
PIC12(L)F1840 FIGURE 19-2: COMPARATOR 1 MODULE SIMPLIFIED BLOCK DIAGRAM C1NCH C1ON(1) 2 C1INTP Interrupt det C1IN0- Set C1IF 0 (2) C1IN1- det 1 C1POL C1VN D C1(3) C1VP C1IN+ DAC FVR Buffer2 0 MUX 1 (2) C1INTN Interrupt MUX C1OUT MC1OUT Q To Data Bus + EN Q1 C1HYS C1SP To ECCP PWM Logic 2 3 C1SYNC C1ON VSS C1PCH<1:0> 0 C1OE TRIS bit C1OUT 2 D (from Timer1) T1CLK Note 1: 2: 3: Q 1 To Timer1 or SR Latch sync_C1OUT When C1ON = 0, the Comparator will produce a ‘0’ at the outp
PIC12(L)F1840 19.2 Comparator Control The comparator has 2 control registers: CM1CON0 and CM1CON1.
PIC12(L)F1840 19.3 Comparator Hysteresis A selectable amount of separation voltage can be added to the input pins of each comparator to provide a hysteresis function to the overall operation. Hysteresis is enabled by setting the C1HYS bit of the CM1CON0 register. See Section 30.0 “Electrical Specifications” for more information. 19.4 Timer1 Gate Operation The output resulting from a comparator operation can be used as a source for gate control of Timer1. See Section 21.
PIC12(L)F1840 19.7 Comparator Negative Input Selection The C1NCH bit of the CM1CON1 register directs one of two analog pins to the comparator inverting input. Note: 19.8 To use C1IN+ and C1INx- pins as analog input, the appropriate bits must be set in the ANSEL register and the corresponding TRIS bits must also be set to disable the output drivers.
PIC12(L)F1840 FIGURE 19-3: ANALOG INPUT MODEL VDD Rs < 10K Analog Input pin VT 0.6V RIC To Comparator VA CPIN 5 pF VT 0.6V ILEAKAGE(1) Vss Legend: CPIN = Input Capacitance ILEAKAGE = Leakage Current at the pin due to various junctions = Interconnect Resistance RIC = Source Impedance RS = Analog Voltage VA = Threshold Voltage VT Note 1: DS40001441D-page 146 See Section 30.0 “Electrical Specifications”. 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 19.
PIC12(L)F1840 REGISTER 19-2: CM1CON1: COMPARATOR C1 CONTROL REGISTER 1 R/W-0/0 R/W-0/0 C1INTP C1INTN R/W-0/0 R/W-0/0 C1PCH<1:0> U-0 U-0 U-0 R/W-0/0 — — — C1NCH bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 C1INTP: Comparator Interrupt on Positive Going Edge Enable bits 1 = The C1IF interrupt flag will
PIC12(L)F1840 20.0 TIMER0 MODULE 20.1.2 In 8-Bit Counter mode, the Timer0 module will increment on every rising or falling edge of the T0CKI pin or the Capacitive Sensing Oscillator (CPSCLK) signal.
PIC12(L)F1840 20.1.3 SOFTWARE PROGRAMMABLE PRESCALER A software programmable prescaler is available for exclusive use with Timer0. The prescaler is enabled by clearing the PSA bit of the OPTION_REG register. Note: The Watchdog Timer (WDT) uses its own independent prescaler. There are eight prescaler options for the Timer0 module ranging from 1:2 to 1:256. The prescale values are selectable via the PS<2:0> bits of the OPTION_REG register.
PIC12(L)F1840 20.
PIC12(L)F1840 NOTES: DS40001441D-page 152 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 21.0 TIMER1 MODULE WITH GATE CONTROL • • • • The Timer1 module is a 16-bit timer/counter with the following features: Figure 21-1 is a block diagram of the Timer1 module.
PIC12(L)F1840 21.1 Timer1 Operation 21.2 The Timer1 module is a 16-bit incrementing counter which is accessed through the TMR1H:TMR1L register pair. Writes to TMR1H or TMR1L directly update the counter. The TMR1CS<1:0> and T1OSCEN bits of the T1CON register are used to select the clock source for Timer1. Table 21-2 displays the clock source selections. 21.2.1 When used with an internal clock source, the module is a timer and increments on every instruction cycle.
PIC12(L)F1840 21.3 Timer1 Prescaler Timer1 has four prescaler options allowing 1, 2, 4 or 8 divisions of the clock input. The T1CKPS bits of the T1CON register control the prescale counter. The prescale counter is not directly readable or writable; however, the prescaler counter is cleared upon a write to TMR1H or TMR1L. 21.4 Timer1 Oscillator A dedicated low-power 32.768 kHz oscillator circuit is built-in between pins T1OSI (input) and T1OSO (amplifier output).
PIC12(L)F1840 21.6.2.1 T1G Pin Gate Operation The T1G pin is one source for Timer1 gate control. It can be used to supply an external source to the Timer1 gate circuitry. 21.6.2.2 Timer0 Overflow Gate Operation When Timer0 increments from FFh to 00h, a low-to-high pulse will automatically be generated and internally supplied to the Timer1 gate circuitry. 21.6.2.3 Comparator C1 Gate Operation The output resulting from a Comparator 1 operation can be selected as a source for Timer1 gate control.
PIC12(L)F1840 21.7 Timer1 Interrupt The Timer1 register pair (TMR1H:TMR1L) increments to FFFFh and rolls over to 0000h. When Timer1 rolls over, the Timer1 interrupt flag bit of the PIR1 register is set. To enable the interrupt on rollover, you must set these bits: • • • • TMR1ON bit of the T1CON register TMR1IE bit of the PIE1 register PEIE bit of the INTCON register GIE bit of the INTCON register The interrupt is cleared by clearing the TMR1IF bit in the Interrupt Service Routine.
PIC12(L)F1840 FIGURE 21-3: TIMER1 GATE ENABLE MODE TMR1GE T1GPOL t1g_in T1CKI T1GVAL Timer1 N FIGURE 21-4: N+1 N+2 N+3 N+4 TIMER1 GATE TOGGLE MODE TMR1GE T1GPOL T1GTM t1g_in T1CKI T1GVAL Timer1 N DS40001441D-page 158 N+1 N+2 N+3 N+4 N+5 N+6 N+7 N+8 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 21-5: TIMER1 GATE SINGLE-PULSE MODE TMR1GE T1GPOL T1GSPM T1GGO/ Cleared by hardware on falling edge of T1GVAL Set by software DONE Counting enabled on rising edge of T1G t1g_in T1CKI T1GVAL Timer1 TMR1GIF N Cleared by software 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 21-6: TIMER1 GATE SINGLE-PULSE AND TOGGLE COMBINED MODE TMR1GE T1GPOL T1GSPM T1GTM T1GGO/ Cleared by hardware on falling edge of T1GVAL Set by software DONE Counting enabled on rising edge of T1G t1g_in T1CKI T1GVAL Timer1 TMR1GIF DS40001441D-page 160 N Cleared by software N+1 N+2 N+3 Set by hardware on falling edge of T1GVAL N+4 Cleared by software 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 21.
PIC12(L)F1840 REGISTER 21-2: T1GCON: TIMER1 GATE CONTROL REGISTER R/W-0/u R/W-0/u R/W-0/u R/W-0/u R/W/HC-0/u R-x/x TMR1GE T1GPOL T1GTM T1GSPM T1GGO/ DONE T1GVAL R/W-0/u R/W-0/u T1GSS<1:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared HC = Bit is cleared by hardware bit 7 TMR1GE: Timer1 Gate Enable bit If T
PIC12(L)F1840 TABLE 21-5: Name ANSELA CCP1CON INTCON SUMMARY OF REGISTERS ASSOCIATED WITH TIMER1 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register on Page — — — ANSA4 — ANSA2 ANSA1 ANSA0 106 P1M<1:0> DC1B<1:0> CCP1M<3:0> 197 GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 74 PIE1 TMR1GIE ADIE RCIE TXIE SSP1IE CCP1IE TMR2IE TMR1IE 75 PIR1 TMR1GIF ADIF RCIF TXIF SSP1IF CCP1IF TMR2IF TMR1IF 77 TMR1H Holding Register for the Most Significant Byte of the
PIC12(L)F1840 NOTES: DS40001441D-page 164 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 22.0 TIMER2 MODULE The Timer2 module incorporates the following features: • 8-bit Timer and Period registers (TMR2 and PR2, respectively) • Readable and writable (both registers) • Software programmable prescaler (1:1, 1:4, 1:16, and 1:64) • Software programmable postscaler (1:1 to 1:16) • Interrupt on TMR2 match with PR2, respectively • Optional use as the shift clock for the MSSP1 modules See Figure 22-1 for a block diagram of Timer2.
PIC12(L)F1840 22.1 Timer2 Operation The clock input to the Timer2 modules is the system instruction clock (FOSC/4). TMR2 increments from 00h on each clock edge. A 4-bit counter/prescaler on the clock input allows direct input, divide-by-4 and divide-by-16 prescale options. These options are selected by the prescaler control bits, T2CKPS<1:0> of the T2CON register. The value of TMR2 is compared to that of the Period register, PR2, on each clock cycle.
PIC12(L)F1840 22.
PIC12(L)F1840 TABLE 22-1: Name CCP1CON INTCON PIE1 SUMMARY OF REGISTERS ASSOCIATED WITH TIMER2 Bit 7 Bit 6 P1M<1:0> Bit 5 Bit 4 Bit 3 DC1B<1:0> Bit 2 Bit 1 Bit 0 CCP1M<3:0> 197 GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 74 75 TMR1GIE ADIE RCIE TXIE SSP1IE CCP1IE TMR2IE TMR1IE PIR1 TMR1GIF ADIF RCIF TXIF SSP1IF CCP1IF TMR2IF TMR1IF PR2 Timer2 Module Period Register T2CON TMR2 Register on Page — T2OUTPS<3:0> 77 165* TMR2ON T2CKPS<1:0> Holding Register for the
PIC12(L)F1840 23.0 DATA SIGNAL MODULATOR The Data Signal Modulator (DSM) is a peripheral which allows the user to mix a data stream, also known as a modulator signal, with a carrier signal to produce a modulated output. Both the carrier and the modulator signals are supplied to the DSM module either internally, from the output of a peripheral, or externally through an input pin.
PIC12(L)F1840 FIGURE 23-1: SIMPLIFIED BLOCK DIAGRAM OF THE DATA SIGNAL MODULATOR MDCH<3:0> VSS MDCIN1 MDCIN2 CLKR CCP1 Reserved No Channel Selected 0000 0001 0010 0011 0100 0101 CARH * * * 1111 MDEN EN Data Signal Modulator MDCHPOL D SYNC MDMS<3:0> MDBIT MDMIN CCP1 Reserved Reserved Reserved Comparator C1 Reserved MSSP1 SDO1 Reserved EUSART Reserved No Channel Selected Q 0000 0001 0010 0011 0100 0101 0110 MOD 0111 1000 1001 1010 0011 * * 1111 1 0 MDCHSYNC MDOUT MDOPOL MDOE D SYNC MDCL<3:0> VSS
PIC12(L)F1840 23.1 DSM Operation The DSM module can be enabled by setting the MDEN bit in the MDCON register. Clearing the MDEN bit in the MDCON register, disables the DSM module by automatically switching the carrier high and carrier low signals to the VSS signal source. The modulator signal source is also switched to the MDBIT in the MDCON register. This not only assures that the DSM module is inactive, but that it is also consuming the least amount of current.
PIC12(L)F1840 FIGURE 23-2: ON OFF KEYING (OOK) SYNCHRONIZATION Carrier Low (CARL) Carrier High (CARH) Modulator (MOD) MDCHSYNC = 1 MDCLSYNC = 0 MDCHSYNC = 1 MDCLSYNC = 1 MDCHSYNC = 0 MDCLSYNC = 0 MDCHSYNC = 0 MDCLSYNC = 1 EXAMPLE 23-1: NO SYNCHRONIZATION (MDSHSYNC = 0, MDCLSYNC = 0) Carrier High (CARH) Carrier Low (CARL) Modulator (MOD) MDCHSYNC = 0 MDCLSYNC = 0 Active Carrier State FIGURE 23-3: CARH CARL CARH CARL CARRIER HIGH SYNCHRONIZATION (MDSHSYNC = 1, MDCLSYNC = 0) Carrier High (CARH) Car
PIC12(L)F1840 FIGURE 23-4: CARRIER LOW SYNCHRONIZATION (MDSHSYNC = 0, MDCLSYNC = 1) Carrier High (CARH) Carrier Low (CARL) Modulator (MOD) MDCHSYNC = 0 MDCLSYNC = 1 Active Carrier State FIGURE 23-5: CARH CARL CARH CARL FULL SYNCHRONIZATION (MDSHSYNC = 1, MDCLSYNC = 1) Carrier High (CARH) Carrier Low (CARL) Modulator (MOD) Falling edges used to sync MDCHSYNC = 1 MDCLSYNC = 1 Active Carrier State CARH 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 23.5 Carrier Source Polarity Select The signal provided from any selected input source for the carrier high and carrier low signals can be inverted. Inverting the signal for the carrier high source is enabled by setting the MDCHPOL bit of the MDCARH register. Inverting the signal for the carrier low source is enabled by setting the MDCLPOL bit of the MDCARL register. 23.6 Carrier Source Pin Disable Some peripherals assert control over their corresponding output pin when they are enabled.
PIC12(L)F1840 23.
PIC12(L)F1840 REGISTER 23-2: MDSRC: MODULATION SOURCE CONTROL REGISTER R/W-x/u U-0 U-0 U-0 MDMSODIS — — — R/W-x/u R/W-x/u R/W-x/u R/W-x/u MDMS<3:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 MDMSODIS: Modulation Source Output Disable bit 1 = Output signal driving the peripheral output pin (selected b
PIC12(L)F1840 REGISTER 23-3: MDCARH: MODULATION HIGH CARRIER CONTROL REGISTER R/W-x/u R/W-x/u R/W-x/u U-0 MDCHODIS MDCHPOL MDCHSYNC — R/W-x/u R/W-x/u R/W-x/u R/W-x/u MDCH<3:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 MDCHODIS: Modulator High Carrier Output Disable bit 1 = Output signal driving the
PIC12(L)F1840 REGISTER 23-4: MDCARL: MODULATION LOW CARRIER CONTROL REGISTER R/W-x/u R/W-x/u R/W-x/u U-0 MDCLODIS MDCLPOL MDCLSYNC — R/W-x/u R/W-x/u R/W-x/u R/W-x/u MDCL<3:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 MDCLODIS: Modulator Low Carrier Output Disable bit 1 = Output signal driving the pe
PIC12(L)F1840 24.0 CAPTURE/COMPARE/PWM MODULES The Capture/Compare/PWM module is a peripheral which allows the user to time and control different events, and to generate Pulse-Width Modulation (PWM) signals. In Capture mode, the peripheral allows the timing of the duration of an event. The Compare mode allows the user to trigger an external event when a predetermined amount of time has expired. The PWM mode can generate Pulse-Width Modulated signals of varying frequency and duty cycle.
PIC12(L)F1840 24.1 Capture Mode 24.1.2 Capture mode makes use of the 16-bit Timer1 resource. When an event occurs on the CCP1 pin, the 16-bit CCPR1H:CCPR1L register pair captures and stores the 16-bit value of the TMR1H:TMR1L register pair, respectively.
PIC12(L)F1840 24.1.5 CAPTURE DURING SLEEP 24.1.6 Capture mode depends upon the Timer1 module for proper operation. There are two options for driving the Timer1 module in Capture mode. It can be driven by the instruction clock (FOSC/4), or by an external clock source. ALTERNATE PIN LOCATIONS This module incorporates I/O pins that can be moved to other locations with the use of the alternate pin function register, APFCON.
PIC12(L)F1840 24.2 Compare Mode 24.2.2 Compare mode makes use of the 16-bit Timer1 resource. The 16-bit value of the CCPR1H:CCPR1L register pair is constantly compared against the 16-bit value of the TMR1H:TMR1L register pair.
PIC12(L)F1840 24.2.6 ALTERNATE PIN LOCATIONS This module incorporates I/O pins that can be moved to other locations with the use of the alternate pin function register, APFCON. To determine which pins can be moved and what their default locations are upon a reset, see Section 12.1 “Alternate Pin Function” for more information.
PIC12(L)F1840 24.3 PWM Overview Pulse-Width Modulation (PWM) is a scheme that provides power to a load by switching quickly between fully on and fully off states. The PWM signal resembles a square wave where the high portion of the signal is considered the on state and the low portion of the signal is considered the off state. The high portion, also known as the pulse width, can vary in time and is defined in steps.
PIC12(L)F1840 24.3.2 SETUP FOR PWM OPERATION The following steps should be taken when configuring the CCP1 module for standard PWM operation: 1. 2. 3. 4. 5. 6. Disable the CCP1 pin output driver by setting the associated TRIS bit. Load the PR2 register with the PWM period value. Configure the CCP1 module for the PWM mode by loading the CCP1CON register with the appropriate values. Load the CCPR1L register and the DC1B1 bits of the CCP1CON register, with the PWM duty cycle value.
PIC12(L)F1840 24.3.5 PWM RESOLUTION EQUATION 24-4: The resolution determines the number of available duty cycles for a given period. For example, a 10-bit resolution will result in 1024 discrete duty cycles, whereas an 8-bit resolution will result in 256 discrete duty cycles. The maximum PWM resolution is 10 bits when PR2 is 255. The resolution is a function of the PR2 register value as shown by Equation 24-4.
PIC12(L)F1840 24.3.6 OPERATION IN SLEEP MODE 24.3.9 In Sleep mode, the TMR2 register will not increment and the state of the module will not change. If the CCP1 pin is driving a value, it will continue to drive that value. When the device wakes up, TMR2 will continue from its previous state. 24.3.7 CHANGES IN SYSTEM CLOCK FREQUENCY ALTERNATE PIN LOCATIONS This module incorporates I/O pins that can be moved to other locations with the use of the alternate pin function register, APFCON.
PIC12(L)F1840 24.4 PWM (Enhanced Mode) The PWM outputs are multiplexed with I/O pins and are designated P1A and P1B. The polarity of the PWM pins is configurable and is selected by setting the bits CCP1M<3:0> in the CCP1CON register appropriately. The enhanced PWM mode generates a Pulse-Width Modulation (PWM) signal on up to two different output pins with up to 10 bits of resolution.
PIC12(L)F1840 TABLE 24-8: EXAMPLE PIN ASSIGNMENTS FOR VARIOUS PWM ENHANCED MODES ECCP Mode P1M<1:0> CCP1/P1A P1B Single 00 Yes(1) Yes(1) Half-Bridge 10 Yes Yes Note 1: PWM Steering enables outputs in Single mode.
PIC12(L)F1840 24.4.1 HALF-BRIDGE MODE In Half-Bridge mode, two pins are used as outputs to drive push-pull loads. The PWM output signal is output on the CCP1/P1A pin, while the complementary PWM output signal is output on the P1B pin (see Figure 24-9). This mode can be used for Half-Bridge applications, as shown in Figure 24-9, or for Full-Bridge applications, where four power switches are being modulated with two PWM signals.
PIC12(L)F1840 24.4.2 ENHANCED PWM AUTOSHUTDOWN MODE The PWM mode supports an Auto-Shutdown mode that will disable the PWM outputs when an external shutdown event occurs. Auto-Shutdown mode places the PWM output pins into a predetermined state. This mode is used to help prevent the PWM from damaging the application. The auto-shutdown sources are selected using the CCP1AS<2:0> bits of the CCP1AS register.
PIC12(L)F1840 24.4.3 AUTO-RESTART MODE The Enhanced PWM can be configured to automatically restart the PWM signal once the autoshutdown condition has been removed. Auto-restart is enabled by setting the P1RSEN bit in the PWM1CON register. If auto-restart is enabled, the CCP1ASE bit will remain set as long as the auto-shutdown condition is active. When the auto-shutdown condition is removed, the CCP1ASE bit will be cleared via hardware and normal operation will resume.
PIC12(L)F1840 24.4.4 PROGRAMMABLE DEAD-BAND DELAY MODE FIGURE 24-12: In half-bridge applications where all power switches are modulated at the PWM frequency, the power switches normally require more time to turn off than to turn on. If both the upper and lower power switches are switched at the same time (one turned on, and the other turned off), both switches may be on for a short period of time until one switch completely turns off.
PIC12(L)F1840 24.4.5 PWM STEERING MODE 24.4.5.1 In Single Output mode, PWM steering allows any of the PWM pins to be the modulated signal. Additionally, the same PWM signal can be simultaneously available on multiple pins. Once the Single Output mode is selected (CCP1M<3:2> = 11 and P1M<1:0> = 00 of the CCP1CON register), the user firmware can bring out the same PWM signal to one or two output pins by setting the appropriate STR1 bits of the PSTR1CON register, as shown in Table 24-8.
PIC12(L)F1840 FIGURE 24-15: EXAMPLE OF STEERING EVENT AT END OF INSTRUCTION (STR1SYNC = 0) PWM Period PWM STR1 P1 PORT Data PORT Data P1n = PWM FIGURE 24-16: EXAMPLE OF STEERING EVENT AT BEGINNING OF INSTRUCTION (STR1SYNC = 1) PWM STR1 P1 PORT Data PORT Data P1n = PWM 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 24.4.7 ALTERNATE PIN LOCATIONS This module incorporates I/O pins that can be moved to other locations with the use of the alternate pin function register, APFCON. To determine which pins can be moved and what their default locations are upon a reset, see Section 12.1 “Alternate Pin Function” for more information.
PIC12(L)F1840 24.
PIC12(L)F1840 REGISTER 24-2: R/W-0/0 CCP1AS: CCP1 AUTO-SHUTDOWN CONTROL REGISTER R/W-0/0 CCP1ASE R/W-0/0 R/W-0/0 CCP1AS<2:0> R/W-0/0 R/W-0/0 R/W-0/0 PSS1AC<1:0> R/W-0/0 PSS1BD<1:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 CCP1ASE: CCP1 Auto-Shutdown Event Status bit 1 = A shutdown event has occurred;
PIC12(L)F1840 REGISTER 24-3: R/W-0/0 PWM1CON: ENHANCED PWM CONTROL REGISTER R/W-0/0 R/W-0/0 R/W-0/0 P1RSEN R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 P1DC<6:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 P1RSEN: PWM Restart Enable bit 1 = Upon auto-shutdown, the CCP1ASE bit clears automatically once the shutdown eve
PIC12(L)F1840 NOTES: DS40001441D-page 200 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 25.0 MASTER SYNCHRONOUS SERIAL PORT MODULE 25.1 Master SSP (MSSP1) Module Overview The Master Synchronous Serial Port (MSSP1) module is a serial interface useful for communicating with other peripheral or microcontroller devices. These peripheral devices may be serial EEPROMs, shift registers, display drivers, A/D converters, etc.
PIC12(L)F1840 The I2C interface supports the following modes and features: • • • • • • • • • • • • • Master mode Slave mode Byte NACKing (Slave mode) Limited Multi-master support 7-bit and 10-bit addressing Start and Stop interrupts Interrupt masking Clock stretching Bus collision detection General call address matching Address masking Address Hold and Data Hold modes Selectable SDA hold times Figure 25-2 is a block diagram of the I2C interface module in Master mode.
PIC12(L)F1840 FIGURE 25-3: MSSP1 BLOCK DIAGRAM (I2C™ SLAVE MODE) Internal Data Bus Read Write SSP1BUF Reg SCL Shift Clock SSP1SR Reg SDA MSb LSb SSP1MSK Reg Match Detect Addr Match SSP1ADD Reg Start and Stop bit Detect 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 25.2 SPI Mode Overview The Serial Peripheral Interface (SPI) bus is a synchronous serial data communication bus that operates in Full-Duplex mode. Devices communicate in a master/slave environment where the master device initiates the communication. A slave device is controlled through a Chip Select known as Slave Select.
PIC12(L)F1840 FIGURE 25-4: SPI MASTER AND MULTIPLE SLAVE CONNECTION SPI Master SCK SCK SDO SDI SDI SDO General I/O General I/O SS General I/O SCK SDI SDO SPI Slave #1 SPI Slave #2 SS SCK SDI SDO SPI Slave #3 SS 25.2.1 SPI MODE REGISTERS The MSSP1 module has five registers for SPI mode operation.
PIC12(L)F1840 25.2.2 SPI MODE OPERATION When initializing the SPI, several options need to be specified. This is done by programming the appropriate control bits (SSP1CON1<5:0> and SSP1STAT<7:6>).
PIC12(L)F1840 FIGURE 25-5: SPI MASTER/SLAVE CONNECTION SPI Master SSP1M<3:0> = 00xx = 1010 SPI Slave SSP1M<3:0> = 010x SDO SDI Serial Input Buffer (BUF) SDI Shift Register (SSP1SR) MSb Serial Input Buffer (SSP1BUF) LSb SCK General I/O Processor 1 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 25.2.3 SPI MASTER MODE The master can initiate the data transfer at any time because it controls the SCK line. The master determines when the slave (Processor 2, Figure 25-5) is to broadcast data by the software protocol. In Master mode, the data is transmitted/received as soon as the SSP1BUF register is written to. If the SPI is only going to receive, the SDO output could be disabled (programmed as an input).
PIC12(L)F1840 25.2.4 SPI SLAVE MODE In Slave mode, the data is transmitted and received as external clock pulses appear on SCK. When the last bit is latched, the SSP1IF interrupt flag bit is set. Before enabling the module in SPI Slave mode, the clock line must match the proper Idle state. The clock line can be observed by reading the SCK pin. The Idle state is determined by the CKP bit of the SSP1CON1 register.
PIC12(L)F1840 FIGURE 25-7: SPI DAISY-CHAIN CONNECTION SPI Master SCK SCK SDO SDI SDI SPI Slave #1 SDO General I/O SS SCK SDI SPI Slave #2 SDO SS SCK SDI SPI Slave #3 SDO SS FIGURE 25-8: SLAVE SELECT SYNCHRONOUS WAVEFORM SS SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0) Write to SSP1BUF Shift register SSP1SR and bit count are reset SSP1BUF to SSP1SR SDO bit 7 bit 6 bit 7 SDI bit 6 bit 0 bit 0 bit 7 bit 7 Input Sample SSP1IF Interrupt Flag SSP1SR to SSP1BUF DS40001441D-page 210 2
PIC12(L)F1840 FIGURE 25-9: SPI MODE WAVEFORM (SLAVE MODE WITH CKE = 0) SS Optional SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0) Write to SSP1BUF Valid SDO bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SDI bit 0 bit 7 Input Sample SSP1IF Interrupt Flag SSP1SR to SSP1BUF Write Collision detection active FIGURE 25-10: SPI MODE WAVEFORM (SLAVE MODE WITH CKE = 1) SS Not Optional SCK (CKP = 0 CKE = 1) SCK (CKP = 1 CKE = 1) Write to SSP1BUF Valid SDO bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1
PIC12(L)F1840 25.2.6 SPI OPERATION IN SLEEP MODE In SPI Master mode, module clocks may be operating at a different speed than when in Full-Power mode; in the case of the Sleep mode, all clocks are halted. Special care must be taken by the user when the MSSP1 clock is much faster than the system clock. In Slave mode, when MSSP1 interrupts are enabled, after the master completes sending data, an MSSP1 interrupt will wake the controller from Sleep.
PIC12(L)F1840 25.3 I2C MODE OVERVIEW FIGURE 25-11: The Inter-Integrated Circuit Bus (I2C) is a multi-master serial data communication bus. Devices communicate in a master/slave environment where the master devices initiate the communication. A Slave device is controlled through addressing. VDD SCL The I2C bus specifies two signal connections: • Serial Clock (SCL) • Serial Data (SDA) Figure 25-11 shows the block diagram of the MSSP1 module when operating in I2C mode.
PIC12(L)F1840 When one device is transmitting a logical one, or letting the line float, and a second device is transmitting a logical zero, or holding the line low, the first device can detect that the line is not a logical one. This detection, when used on the SCL line, is called clock stretching. Clock stretching gives slave devices a mechanism to control the flow of data. When this detection is used on the SDA line, it is called arbitration.
PIC12(L)F1840 25.4 I2C MODE OPERATION All MSSP1 I2C communication is byte oriented and shifted out MSb first. Six SFR registers and 2 interrupt flags interface the module with the PIC® microcontroller and user software. Two pins, SDA and SCL, are exercised by the module to communicate with other external I2C devices. 25.4.1 BYTE FORMAT All communication in I2C is done in 9-bit segments. A byte is sent from a master to a slave or vice-versa, followed by an Acknowledge bit sent back.
PIC12(L)F1840 25.4.5 START CONDITION 25.4.7 2 The I C specification defines a Start condition as a transition of SDA from a high to a low state while SCL line is high. A Start condition is always generated by the master and signifies the transition of the bus from an Idle to an Active state. Figure 25-12 shows wave forms for Start and Stop conditions. A Restart is valid any time that a Stop would be valid. A master can issue a Restart if it wishes to hold the bus after terminating the current transfer.
PIC12(L)F1840 25.4.9 ACKNOWLEDGE SEQUENCE The 9th SCL pulse for any transferred byte in I2C is dedicated as an Acknowledge. It allows receiving devices to respond back to the transmitter by pulling the SDA line low. The transmitter must release control of the line during this time to shift in the response. The Acknowledge (ACK) is an active-low signal, pulling the SDA line low indicated to the transmitter that the device has received the transmitted data and is ready to receive more.
PIC12(L)F1840 25.5.2 SLAVE RECEPTION When the R/W bit of a matching received address byte is clear, the R/W bit of the SSP1STAT register is cleared. The received address is loaded into the SSP1BUF register and acknowledged. When the overflow condition exists for a received address, then not Acknowledge is given. An overflow condition is defined as either bit BF of the SSP1STAT register is set, or bit SSP1OV of the SSP1CON1 register is set. The BOEN bit of the SSP1CON3 register modifies this operation.
2011-2013 Microchip Technology Inc. SSP1OV BF SSP1IF S 1 A7 2 A6 3 A5 4 A4 5 A3 Receiving Address 6 A2 7 A1 8 9 ACK 1 D7 2 D6 4 5 D3 6 D2 7 D1 SSP1BUF is read Cleared by software 3 D4 Receiving Data D5 8 9 2 D6 First byte of data is available in SSP1BUF 1 D0 ACK D7 4 5 D3 6 D2 7 D1 8 D0 SSP1OV set because SSP1BUF is still full. ACK is not sent.
DS40001441D-page 220 CKP SSP1OV BF SSP1IF 1 SCL S A7 2 A6 3 A5 4 A4 5 A3 6 A2 7 A1 8 9 R/W=0 ACK SEN 2 D6 3 D5 4 D4 5 D3 6 D2 7 D1 8 D0 CKP is written to ‘1’ in software, releasing SCL SSP1BUF is read Cleared by software Clock is held low until CKP is set to ‘1’ 1 D7 Receive Data 9 ACK SEN 3 D5 4 D4 5 D3 First byte of data is available in SSP1BUF 6 D2 7 D1 SSP1OV set because SSP1BUF is still full. ACK is not sent.
2011-2013 Microchip Technology Inc.
DS40001441D-page 222 P S ACKTIM CKP ACKDT BF SSP1IF S Receiving Address 4 5 6 7 8 When AHEN = 1; on the 8th falling edge of SCL of an address byte, CKP is cleared Slave software clears ACKDT to ACK the received byte Received address is loaded into SSP1BUF 2 3 ACKTIM is set by hardware on 8th falling edge of SCL 1 A7 A6 A5 A4 A3 A2 A1 9 ACK Receive Data 2 3 4 5 6 7 8 ACKTIM is cleared by hardware on 9th rising edge of SCL When DHEN = 1; on the 8th falling edge of SCL of a receive
PIC12(L)F1840 25.5.3 SLAVE TRANSMISSION 25.5.3.2 7-bit Transmission When the R/W bit of the incoming address byte is set and an address match occurs, the R/W bit of the SSP1STAT register is set. The received address is loaded into the SSP1BUF register, and an ACK pulse is sent by the slave on the ninth bit. A master device can transmit a read request to a slave, and then clock data out of the slave. The list below outlines what software for a slave will need to do to accomplish a standard transmission.
DS40001441D-page 224 P S D/A R/W ACKSTAT CKP BF SSPIF S 1 2 5 6 7 Received address is read from SSPBUF 4 Indicates an address has been received R/W is copied from the matching address byte When R/W is set SCL is always held low after 9th SCL falling edge 3 8 9 Automatic 2 3 4 5 Set by software Data to transmit is loaded into SSPBUF Cleared by software 1 6 7 8 9 D7 D6 D5 D4 D3 D2 D1 D0 ACK Transmitting Data 2 3 4 5 7 8 CKP is not held for not ACK 6 Masters not AC
PIC12(L)F1840 25.5.3.3 7-bit Transmission with Address Hold Enabled Setting the AHEN bit of the SSP1CON3 register enables additional clock stretching and interrupt generation after the 8th falling edge of a received matching address. Once a matching address has been clocked in, CKP is cleared and the SSP1IF interrupt is set. Figure 25-19 displays a standard waveform of a 7-bit Address Slave Transmission with AHEN enabled. 1. 2. Bus starts Idle.
DS40001441D-page 226 D/A R/W ACKTIM CKP ACKSTAT ACKDT BF SSP1IF S Receiving Address 2 4 5 6 7 8 Slave clears ACKDT to ACK address ACKTIM is set on 8th falling edge of SCL 9 ACK When R/W = 1; CKP is always cleared after ACK R/W = 1 Received address is read from SSP1BUF 3 When AHEN = 1; CKP is cleared by hardware after receiving matching address.
PIC12(L)F1840 25.5.4 SLAVE MODE 10-BIT ADDRESS RECEPTION This section describes a standard sequence of events for the MSSP1 module configured as an I2C slave in 10-bit Addressing mode. Figure 25-20 is used as a visual reference for this description. This is a step by step process of what must be done by slave software to accomplish I2C communication. 1. 2. 3. 4. 5. 6. 7. 8. Bus starts Idle. Master sends Start condition; S bit of SSP1STAT is set; SSP1IF is set if interrupt on Start detect is enabled.
DS40001441D-page 228 CKP UA BF SSP1IF S 1 1 2 1 5 6 7 0 A9 A8 8 Set by hardware on 9th falling edge 4 1 When UA = 1; SCL is held low 9 ACK If address matches SSP1ADD it is loaded into SSP1BUF 3 1 Receive First Address Byte 1 3 4 5 6 7 8 Software updates SSP1ADD and releases SCL 2 9 A7 A6 A5 A4 A3 A2 A1 A0 ACK Receive Second Address Byte 1 3 4 5 6 7 8 9 1 3 4 5 6 7 Data is read from SSP1BUF SCL is held low while CKP = 0 2 8 9 D7 D6 D5 D4 D3 D2 D1 D0 ACK
2011-2013 Microchip Technology Inc.
DS40001441D-page 230 D/A R/W ACKSTAT CKP UA BF SSP1IF 4 5 6 7 Set by hardware 3 Indicates an address has been received UA indicates SSP1ADD must be updated SSP1BUF loaded with received address 2 8 9 1 SCL S Receiving Address R/W = 0 1 1 1 1 0 A9 A8 ACK 1 3 4 5 6 7 8 After SSP1ADD is updated, UA is cleared and SCL is released Cleared by software 2 9 A7 A6 A5 A4 A3 A2 A1 A0 ACK Receiving Second Address Byte 1 4 5 6 7 8 Set by hardware 2 3 R/W is copied from the matchin
PIC12(L)F1840 25.5.6 CLOCK STRETCHING Clock stretching occurs when a device on the bus holds the SCL line low effectively pausing communication. The slave may stretch the clock to allow more time to handle data or prepare a response for the master device. A master device is not concerned with stretching as anytime it is active on the bus and not transferring data it is stretching. Any stretching done by a slave is invisible to the master software and handled by the hardware that generates SCL.
PIC12(L)F1840 25.5.7 CLOCK SYNCHRONIZATION AND THE CKP BIT Any time the CKP bit is cleared, the module will wait for the SCL line to go low and then hold it. However, clearing the CKP bit will not assert the SCL output low until the SCL output is already sampled low. Therefore, the CKP bit will not assert the SCL line until an external I2C master device has already asserted the SCL line.
PIC12(L)F1840 25.5.8 In 10-bit Address mode, the UA bit will not be set on the reception of the general call address. The slave will prepare to receive the second byte as data, just as it would in 7-bit mode. GENERAL CALL ADDRESS SUPPORT The addressing procedure for the I2C bus is such that the first byte after the Start condition usually determines which device will be the slave addressed by the master device. The exception is the general call address which can address all devices.
PIC12(L)F1840 25.6 I2C MASTER MODE 25.6.1 I2C MASTER MODE OPERATION Master mode is enabled by setting and clearing the appropriate SSPM bits in the SSPCON1 register and by setting the SSPEN bit. In Master mode, the SDA and SCK pins must be configured as inputs. The MSSP peripheral hardware will override the output driver TRIS controls when necessary to drive the pins low. The master device generates all of the serial clock pulses and the Start and Stop conditions.
PIC12(L)F1840 25.6.2 CLOCK ARBITRATION Clock arbitration occurs when the master, during any receive, transmit or Repeated Start/Stop condition, releases the SCL pin (SCL allowed to float high). When the SCL pin is allowed to float high, the Baud Rate Generator (BRG) is suspended from counting until the SCL pin is actually sampled high. When the SCL pin is sampled high, the Baud Rate Generator is reloaded with the contents of SSP1ADD<7:0> and begins counting.
PIC12(L)F1840 25.6.4 I2C MASTER MODE START by hardware; the Baud Rate Generator is suspended, leaving the SDA line held low and the Start condition is complete. CONDITION TIMING To initiate a Start condition (Figure 25-26), the user sets the Start Enable bit, SEN bit of the SSP1CON2 register. If the SDA and SCL pins are sampled high, the Baud Rate Generator is reloaded with the contents of SSP1ADD<7:0> and starts its count.
PIC12(L)F1840 25.6.5 I2C MASTER MODE REPEATED cally cleared and the Baud Rate Generator will not be reloaded, leaving the SDA pin held low. As soon as a Start condition is detected on the SDA and SCL pins, the S bit of the SSP1STAT register will be set. The SSP1IF bit will not be set until the Baud Rate Generator has timed out.
PIC12(L)F1840 25.6.6 I2C MASTER MODE TRANSMISSION Transmission of a data byte, a 7-bit address or the other half of a 10-bit address is accomplished by simply writing a value to the SSP1BUF register. This action will set the Buffer Full flag bit, BF, and allow the Baud Rate Generator to begin counting and start the next transmission. Each bit of address/data will be shifted out onto the SDA pin after the falling edge of SCL is asserted. SCL is held low for one Baud Rate Generator rollover count (TBRG).
2011-2013 Microchip Technology Inc.
PIC12(L)F1840 25.6.7 I2C MASTER MODE RECEPTION Master mode reception (Figure 25-29) is enabled by programming the Receive Enable bit, RCEN bit of the SSP1CON2 register. Note: The MSSP1 module must be in an Idle state before the RCEN bit is set or the RCEN bit will be disregarded. The Baud Rate Generator begins counting and on each rollover, the state of the SCL pin changes (high-to-low/low-to-high) and data is shifted into the SSP1SR.
2011-2013 Microchip Technology Inc.
PIC12(L)F1840 25.6.8 ACKNOWLEDGE SEQUENCE TIMING 25.6.9 A Stop bit is asserted on the SDA pin at the end of a receive/transmit by setting the Stop Sequence Enable bit, PEN bit of the SSP1CON2 register. At the end of a receive/transmit, the SCL line is held low after the falling edge of the ninth clock. When the PEN bit is set, the master will assert the SDA line low. When the SDA line is sampled low, the Baud Rate Generator is reloaded and counts down to ‘0’.
PIC12(L)F1840 FIGURE 25-31: STOP CONDITION RECEIVE OR TRANSMIT MODE SCL = 1 for TBRG, followed by SDA = 1 for TBRG after SDA sampled high. P bit (SSP1STAT<4>) is set. Write to SSP1CON2, set PEN PEN bit (SSP1CON2<2>) is cleared by hardware and the SSP1IF bit is set Falling edge of 9th clock TBRG SCL SDA ACK P TBRG TBRG TBRG SCL brought high after TBRG SDA asserted low before rising edge of clock to setup Stop condition Note: TBRG = one Baud Rate Generator period. 25.6.
PIC12(L)F1840 FIGURE 25-32: BUS COLLISION TIMING FOR TRANSMIT AND ACKNOWLEDGE Data changes while SCL = 0 SDA line pulled low by another source SDA released by master Sample SDA. While SCL is high, data does not match what is driven by the master. Bus collision has occurred. SDA SCL Set bus collision interrupt (BCL1IF) BCL1IF DS40001441D-page 244 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 25.6.13.1 Bus Collision During a Start Condition During a Start condition, a bus collision occurs if: a) b) SDA or SCL are sampled low at the beginning of the Start condition (Figure 25-33). SCL is sampled low before SDA is asserted low (Figure 25-34). During a Start condition, both the SDA and the SCL pins are monitored. If the SDA pin is sampled low during this count, the BRG is reset and the SDA line is asserted early (Figure 25-35).
PIC12(L)F1840 FIGURE 25-34: BUS COLLISION DURING START CONDITION (SCL = 0) SDA = 0, SCL = 1 TBRG TBRG SDA Set SEN, enable Start sequence if SDA = 1, SCL = 1 SCL SCL = 0 before SDA = 0, bus collision occurs. Set BCL1IF. SEN SCL = 0 before BRG time-out, bus collision occurs. Set BCL1IF.
PIC12(L)F1840 25.6.13.2 Bus Collision During a Repeated Start Condition If SDA is low, a bus collision has occurred (i.e., another master is attempting to transmit a data ‘0’, Figure 25-36). If SDA is sampled high, the BRG is reloaded and begins counting. If SDA goes from high-to-low before the BRG times out, no bus collision occurs because no two masters can assert SDA at exactly the same time.
PIC12(L)F1840 25.6.13.3 Bus Collision During a Stop Condition The Stop condition begins with SDA asserted low. When SDA is sampled low, the SCL pin is allowed to float. When the pin is sampled high (clock arbitration), the Baud Rate Generator is loaded with SSP1ADD and counts down to 0. After the BRG times out, SDA is sampled. If SDA is sampled low, a bus collision has occurred. This is due to another master attempting to drive a data ‘0’ (Figure 25-38).
PIC12(L)F1840 TABLE 25-3: Name INTCON SUMMARY OF REGISTERS ASSOCIATED WITH I2C™ OPERATION Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 74 PIE1 TMR1GIE ADIE RCIE TXIE SSP1IE CCP1IE TMR2IE TMR1IE 75 PIE2 OSFIE — C1IE EEIE BCL1IE — — — 76 PIR1 TMR1GIF ADIF RCIF TXIF SSP1IF CCP1IF TMR2IF PIR2 OSFIF — C1IF EEIF BCL1IF — — SSP1ADD ADD<7:0> SSP1BUF Synchronous Serial Port Receive Buffer/T
PIC12(L)F1840 25.7 BAUD RATE GENERATOR The MSSP1 module has a Baud Rate Generator available for clock generation in both I2C and SPI Master modes. The Baud Rate Generator (BRG) reload value is placed in the SSP1ADD register (Register 25-6). When a write occurs to SSP1BUF, the Baud Rate Generator will automatically begin counting down. module clock line. The logic dictating when the reload signal is asserted depends on the mode the MSSP1 is being operated in.
PIC12(L)F1840 25.
PIC12(L)F1840 REGISTER 25-2: SSP1CON1: SSP1 CONTROL REGISTER 1 R/C/HS-0/0 R/C/HS-0/0 R/W-0/0 R/W-0/0 WCOL SSP1OV SSP1EN CKP R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 SSP1M<3:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared HS = Bit is set by hardware C = User cleared bit 7 WCOL: Write Collision Detect bit Master mode:
PIC12(L)F1840 REGISTER 25-3: SSP1CON2: SSP1 CONTROL REGISTER 2 R/W-0/0 R-0/0 R/W-0/0 R/S/HS-0/0 R/S/HS-0/0 R/S/HS-0/0 R/S/HS-0/0 R/W/HS-0/0 GCEN ACKSTAT ACKDT ACKEN RCEN PEN RSEN SEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared HC = Cleared by hardware S = User set bit 7 GCEN: General Call Enable bit (i
PIC12(L)F1840 REGISTER 25-4: SSP1CON3: SSP1 CONTROL REGISTER 3 R-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 ACKTIM PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 ACKTIM: Acknowledge Time Status bit (I2C mode only)(3) 1 = Indicates the I2C bus is in
PIC12(L)F1840 REGISTER 25-5: R/W-1/1 SSP1MSK: SSP1 MASK REGISTER R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 MSK<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-1 MSK<7:1>: Mask bits 1 = The received address bit n is compared to SSP1ADD to detect I2C address match 0 = The received address bi
PIC12(L)F1840 NOTES: DS40001441D-page 256 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 26.
PIC12(L)F1840 FIGURE 26-2: EUSART RECEIVE BLOCK DIAGRAM SPEN CREN RX/DT pin Baud Rate Generator Data Recovery FOSC BRG16 +1 SPBRGH SPBRGL RSR Register MSb Pin Buffer and Control Multiplier x4 x16 x64 SYNC 1 X 0 0 0 BRGH X 1 1 0 0 BRG16 X 1 0 1 0 Stop RCIDL OERR (8) ••• 7 1 LSb 0 START RX9 ÷n n FERR RX9D RCREG Register 8 FIFO Data Bus RCIF RCIE Interrupt The operation of the EUSART module is controlled through three registers: • Transmit Status and Control (TXSTA) • Rece
PIC12(L)F1840 26.1 EUSART Asynchronous Mode The EUSART transmits and receives data using the standard non-return-to-zero (NRZ) format. NRZ is implemented with two levels: a VOH mark state which represents a ‘1’ data bit, and a VOL space state which represents a ‘0’ data bit. NRZ refers to the fact that consecutively transmitted data bits of the same value stay at the output level of that bit without returning to a neutral level between each bit transmission.
PIC12(L)F1840 26.1.1.5 TSR Status 26.1.1.7 The TRMT bit of the TXSTA register indicates the status of the TSR register. This is a read-only bit. The TRMT bit is set when the TSR register is empty and is cleared when a character is transferred to the TSR register from the TXREG. The TRMT bit remains clear until all bits have been shifted out of the TSR register. No interrupt logic is tied to this bit, so the user has to poll this bit to determine the TSR status. Note: 26.1.1.6 1. 2. 3.
PIC12(L)F1840 TABLE 26-1: SUMMARY OF REGISTERS ASSOCIATED WITH ASYNCHRONOUS TRANSMISSION Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register on Page ABDOVF RCIDL — SCKP BRG16 — WUE ABDEN 269 GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 74 PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 75 PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 77 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 268 Name BAUDCON INTCON RCSTA SPBRGL BRG<7:0> 270*
PIC12(L)F1840 26.1.2 EUSART ASYNCHRONOUS RECEIVER The Asynchronous mode is typically used in RS-232 systems. The receiver block diagram is shown in Figure 26-2. The data is received on the RX/DT pin and drives the data recovery block. The data recovery block is actually a high-speed shifter operating at 16 times the baud rate, whereas the serial Receive Shift Register (RSR) operates at the bit rate.
PIC12(L)F1840 26.1.2.4 Receive Framing Error Each character in the receive FIFO buffer has a corresponding framing error Status bit. A framing error indicates that a Stop bit was not seen at the expected time. The framing error status is accessed via the FERR bit of the RCSTA register. The FERR bit represents the status of the top unread character in the receive FIFO. Therefore, the FERR bit must be read before reading the RCREG.
PIC12(L)F1840 26.1.2.8 Asynchronous Reception Set-up: 26.1.2.9 1. Initialize the SPBRGH, SPBRGL register pair and the BRGH and BRG16 bits to achieve the desired baud rate (see Section 26.4 “EUSART Baud Rate Generator (BRG)”). 2. Clear the ANSEL bit for the RX pin (if applicable). 3. Enable the serial port by setting the SPEN bit. The SYNC bit must be clear for asynchronous operation. 4. If interrupts are desired, set the RCIE bit of the PIE1 register and the GIE and PEIE bits of the INTCON register. 5.
PIC12(L)F1840 TABLE 26-2: SUMMARY OF REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register on Page ABDOVF RCIDL — SCKP BRG16 — WUE ABDEN 269 GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 74 PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 75 PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF Name BAUDCON INTCON RCREG RCSTA EUSART Receive Data Register SPEN RX9 SREN SPBRGL ADDEN FERR OERR RX9
PIC12(L)F1840 26.2 Clock Accuracy with Asynchronous Operation The factory calibrates the internal oscillator block output (INTOSC). However, the INTOSC frequency may drift as VDD or temperature changes, and this directly affects the asynchronous baud rate. Two methods may be used to adjust the baud rate clock, but both require a reference clock source of some kind. DS40001441D-page 266 The first (preferred) method uses the OSCTUNE register to adjust the INTOSC output.
PIC12(L)F1840 26.
PIC12(L)F1840 REGISTER 26-2: RCSTA: RECEIVE STATUS AND CONTROL REGISTER R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R-0/0 R-0/0 R-x/x SPEN RX9 SREN CREN ADDEN FERR OERR RX9D bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 SPEN: Serial Port Enable bit 1 = Serial port enabled (configures RX/DT and TX/CK pins
PIC12(L)F1840 REGISTER 26-3: BAUDCON: BAUD RATE CONTROL REGISTER R-0/0 R-1/1 U-0 R/W-0/0 R/W-0/0 U-0 R/W-0/0 R/W-0/0 ABDOVF RCIDL — SCKP BRG16 — WUE ABDEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 ABDOVF: Auto-Baud Detect Overflow bit Asynchronous mode: 1 = Auto-baud timer overflowed 0 = Auto-bau
PIC12(L)F1840 26.4 EUSART Baud Rate Generator (BRG) The Baud Rate Generator (BRG) is an 8-bit or 16-bit timer that is dedicated to the support of both the asynchronous and synchronous EUSART operation. By default, the BRG operates in 8-bit mode. Setting the BRG16 bit of the BAUDCON register selects 16-bit mode. The SPBRGH, SPBRGL register pair determines the period of the free running baud rate timer.
PIC12(L)F1840 TABLE 26-3: BAUD RATE FORMULAS Configuration Bits BRG/EUSART Mode Baud Rate Formula 0 8-bit/Asynchronous FOSC/[64 (n+1)] 0 1 8-bit/Asynchronous 0 1 0 16-bit/Asynchronous 0 1 1 16-bit/Asynchronous 1 0 x 8-bit/Synchronous 1 x 16-bit/Synchronous SYNC BRG16 BRGH 0 0 0 1 Legend: FOSC/[4 (n+1)] x = Don’t care, n = value of SPBRGH, SPBRGL register pair.
PIC12(L)F1840 TABLE 26-5: BAUD RATES FOR ASYNCHRONOUS MODES SYNC = 0, BRGH = 0, BRG16 = 0 BAUD RATE FOSC = 32.000 MHz Actual Rate % Error SPBRG value (decimal) FOSC = 20.000 MHz Actual Rate % Error SPBRG value (decimal) FOSC = 18.432 MHz Actual Rate % Error SPBRG value (decimal) FOSC = 11.0592 MHz Actual Rate % Error SPBRG value (decimal) 300 — — — — — — — — — — — — 1200 — — — 1221 1.73 255 1200 0.00 239 1200 0.00 143 2400 2404 0.16 207 2404 0.16 129 2400 0.
PIC12(L)F1840 TABLE 26-5: BAUD RATES FOR ASYNCHRONOUS MODES (CONTINUED) SYNC = 0, BRGH = 1, BRG16 = 0 BAUD RATE FOSC = 8.000 MHz Actual Rate % Error SPBRG value (decimal) FOSC = 4.000 MHz Actual Rate % Error SPBRG value (decimal) FOSC = 3.6864 MHz Actual Rate FOSC = 1.000 MHz % Error SPBRG value (decimal) Actual Rate % Error SPBRG value (decimal) 300 1200 — — — — — — — 1202 — 0.16 — 207 — 1200 — 0.00 — 191 300 1202 0.16 0.16 207 51 2400 2404 0.16 207 2404 0.
PIC12(L)F1840 TABLE 26-5: BAUD RATES FOR ASYNCHRONOUS MODES (CONTINUED) SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1 BAUD RATE FOSC = 32.000 MHz FOSC = 20.000 MHz FOSC = 18.432 MHz FOSC = 11.0592 MHz Actual Rate % Error SPBRG value (decimal) 300 1200 300.0 1200 0.00 0.00 26666 6666 300.0 1200 0.00 -0.01 16665 4166 300.0 1200 0.00 0.00 15359 3839 300.0 1200 0.00 0.00 9215 2303 2400 2400 0.01 3332 2400 0.02 2082 2400 0.00 1919 2400 0.
PIC12(L)F1840 26.4.1 AUTO-BAUD DETECT The EUSART module supports automatic detection and calibration of the baud rate. In the Auto-Baud Detect (ABD) mode, the clock to the BRG is reversed. Rather than the BRG clocking the incoming RX signal, the RX signal is timing the BRG. The Baud Rate Generator is used to time the period of a received 55h (ASCII “U”) which is the Sync character for the LIN bus. The unique feature of this character is that it has five rising edges including the Stop bit edge.
PIC12(L)F1840 26.4.2 AUTO-BAUD OVERFLOW During the course of automatic baud detection, the ABDOVF bit of the BAUDCON register will be set if the baud rate counter overflows before the fifth rising edge is detected on the RX pin. The ABDOVF bit indicates that the counter has exceeded the maximum count that can fit in the 16 bits of the SPBRGH:SPBRGL register pair. After the ABDOVF bit has been set, the counter continues to count until the fifth rising edge is detected on the RX pin.
PIC12(L)F1840 FIGURE 26-7: AUTO-WAKE-UP BIT (WUE) TIMING DURING NORMAL OPERATION Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 Auto Cleared Bit set by user WUE bit RX/DT Line RCIF Note 1: Cleared due to User Read of RCREG The EUSART remains in Idle while the WUE bit is set.
PIC12(L)F1840 26.4.4 BREAK CHARACTER SEQUENCE The EUSART module has the capability of sending the special Break character sequences that are required by the LIN bus standard. A Break character consists of a Start bit, followed by 12 ‘0’ bits and a Stop bit. To send a Break character, set the SENDB and TXEN bits of the TXSTA register. The Break character transmission is then initiated by a write to the TXREG. The value of data written to TXREG will be ignored and all ‘0’s will be transmitted.
PIC12(L)F1840 26.5 EUSART Synchronous Mode Synchronous serial communications are typically used in systems with a single master and one or more slaves. The master device contains the necessary circuitry for baud rate generation and supplies the clock for all devices in the system. Slave devices can take advantage of the master clock by eliminating the internal clock generation circuitry. There are two signal lines in Synchronous mode: a bidirectional data line and a clock line.
PIC12(L)F1840 FIGURE 26-10: SYNCHRONOUS TRANSMISSION RX/DT pin bit 0 bit 1 Word 1 bit 2 bit 7 bit 0 bit 1 Word 2 bit 7 TX/CK pin (SCKP = 0) TX/CK pin (SCKP = 1) Write to TXREG Reg Write Word 1 Write Word 2 TXIF bit (Interrupt Flag) TRMT bit TXEN bit ‘1’ Note: ‘1’ Sync Master mode, SPBRGL = 0, continuous transmission of two 8-bit words.
PIC12(L)F1840 26.5.1.5 Synchronous Master Reception Data is received at the RX/DT pin. The RX/DT pin output driver is automatically disabled when the EUSART is configured for synchronous master receive operation. In Synchronous mode, reception is enabled by setting either the Single Receive Enable bit (SREN of the RCSTA register) or the Continuous Receive Enable bit (CREN of the RCSTA register).
PIC12(L)F1840 FIGURE 26-12: SYNCHRONOUS RECEPTION (MASTER MODE, SREN) RX/DT pin bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 TX/CK pin (SCKP = 0) TX/CK pin (SCKP = 1) Write to bit SREN SREN bit CREN bit ‘0’ ‘0’ RCIF bit (Interrupt) Read RCREG Note: Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0.
PIC12(L)F1840 26.5.2 SYNCHRONOUS SLAVE MODE The following bits are used to configure the EUSART for synchronous slave operation: • • • • • SYNC = 1 CSRC = 0 SREN = 0 (for transmit); SREN = 1 (for receive) CREN = 0 (for transmit); CREN = 1 (for receive) SPEN = 1 1. 2. 3. 4. Setting the SYNC bit of the TXSTA register configures the device for synchronous operation. Clearing the CSRC bit of the TXSTA register configures the device as a slave.
PIC12(L)F1840 26.5.2.3 EUSART Synchronous Slave Reception 26.5.2.4 The operation of the Synchronous Master and Slave modes is identical (Section 26.5.1.5 “Synchronous Master Reception”), with the following exceptions: • Sleep • CREN bit is always set, therefore the receiver is never idle • SREN bit, which is a “don’t care” in Slave mode 1. 2. 3. A character may be received while in Sleep mode by setting the CREN bit prior to entering Sleep.
PIC12(L)F1840 26.6 EUSART Operation During Sleep The EUSART will remain active during Sleep only in the Synchronous Slave mode. All other modes require the system clock and therefore cannot generate the necessary signals to run the Transmit or Receive Shift registers during Sleep. Synchronous Slave mode uses an externally generated clock to run the Transmit and Receive Shift registers. 26.6.
PIC12(L)F1840 NOTES: DS40001441D-page 286 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 27.0 CAPACITIVE SENSING (CPS) MODULE The Capacitive Sensing (CPS) module allows for an interaction with an end user without a mechanical interface. In a typical application, the CPS module is attached to a pad on a Printed Circuit Board (PCB), which is electrically isolated from the end user. When the end user places their finger over the PCB pad, a capacitive load is added, causing a frequency shift in the CPS module.
PIC12(L)F1840 FIGURE 27-2: CAPACITIVE SENSING OSCILLATOR BLOCK DIAGRAM Oscillator Module VDD (1) + (2) - S CPSx (1) Analog Pin - Q CPSCLK R (2) + Internal References Ref- 0 0 1 Ref+ DAC 1 FVR CPSRM Note 1: 2: Module Enable and Power mode selections are not shown. Comparator remains active in Noise Detection mode. DS40001441D-page 288 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 27.1 Analog MUX 27.3 Voltage References The CPS module can monitor up to four inputs. See Register 27-2 for details. The capacitive sensing inputs are defined as CPS<7:0>, as applicable to the device. To determine if a frequency change has occurred the user must: The capacitive sensing oscillator uses voltage references to provide two voltage thresholds for oscillation. The upper voltage threshold is referred to as Ref+ and the lower voltage threshold is referred to as Ref-.
PIC12(L)F1840 27.4 Current Ranges The capacitive sensing oscillator can operate in one of seven different power modes. The power modes are separated into two ranges; the low range and the high range. When the oscillator’s low range is selected, the fixed internal voltage references of the capacitive sensing oscillator are being used. When the oscillator’s high range is selected, the variable voltage references supplied by the FVR and DAC modules are being used.
PIC12(L)F1840 27.5 Timer Resources 27.7 To measure the change in frequency of the capacitive sensing oscillator, a fixed time base is required. For the period of the fixed time base, the capacitive sensing oscillator is used to clock either Timer0 or Timer1. The frequency of the capacitive sensing oscillator is equal to the number of counts in the timer divided by the period of the fixed time base. 27.
PIC12(L)F1840 27.7.3 FREQUENCY THRESHOLD The frequency threshold should be placed midway between the value of nominal frequency and the reduced frequency of the capacitive sensing oscillator. Refer to Application Note AN1103, “Software Handling for Capacitive Sensing” (DS01103) for more detailed information on the software required for CPS module.
PIC12(L)F1840 27.
PIC12(L)F1840 REGISTER 27-2: CPSCON1: CAPACITIVE SENSING CONTROL REGISTER 1 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — R/W-0/0 R/W-0/0 CPSCH<1:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-2 Unimplemented: Read as ‘0’ bit 1-0 CPSCH<1:0>: Capacitive Sensing Channel Select bits If CPSON = 0: These bits are
PIC12(L)F1840 28.0 IN-CIRCUIT SERIAL PROGRAMMING™ (ICSP™) ICSP™ programming allows customers to manufacture circuit boards with unprogrammed devices. Programming can be done after the assembly process allowing the device to be programmed with the most recent firmware or a custom firmware. Five pins are needed for ICSP™ programming: • ICSPCLK • ICSPDAT • MCLR/VPP • VDD • VSS In Program/Verify mode the program memory, user IDs and the Configuration Words are programmed through serial communications.
PIC12(L)F1840 28.2 Note: The MPLAB ICD 2 produces a VPP voltage greater than the maximum VPP specification of the PIC12F/LF1840. Low-Voltage Programming Entry Mode The Low-Voltage Programming Entry mode allows the PIC® Flash MCUs to be programmed using VDD only, without high voltage. When the LVP bit of Configuration Words is set to ‘1’, the low-voltage ICSP programming entry is enabled. To disable the Low-Voltage ICSP mode, the LVP bit must be programmed to ‘0’.
PIC12(L)F1840 Another connector often found in use with the PICkit™ programmers is a standard 6-pin header with 0.1 inch spacing. Refer to Figure 28-3. FIGURE 28-3: PICkit™ PROGRAMMER STYLE CONNECTOR INTERFACE Pin 1 Indicator Pin Description* 1 2 3 4 5 6 1 = VPP/MCLR 2 = VDD Target 3 = VSS (ground) 4 = ICSPDAT 5 = ICSPCLK 6 = No Connect * The 6-pin header (0.100" spacing) accepts 0.025" square pins. 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 For additional interface recommendations, refer to your specific device programmer manual prior to PCB design. It is recommended that isolation devices be used to separate the programming pins from other circuitry. The type of isolation is highly dependent on the specific application and may include devices such as resistors, diodes, or even jumpers. See Figure 28-4 for more information.
PIC12(L)F1840 29.0 INSTRUCTION SET SUMMARY 29.1 Read-Modify-Write Operations • Byte Oriented • Bit Oriented • Literal and Control Any instruction that specifies a file register as part of the instruction performs a Read-Modify-Write (R-M-W) operation. The register is read, the data is modified, and the result is stored according to either the instruction, or the destination designator ‘d’. A read operation is performed on a register even if the instruction writes to that register.
PIC12(L)F1840 FIGURE 29-1: GENERAL FORMAT FOR INSTRUCTIONS Byte-oriented file register operations 13 8 7 6 OPCODE d f (FILE #) 0 d = 0 for destination W d = 1 for destination f f = 7-bit file register address Bit-oriented file register operations 13 10 9 7 6 OPCODE b (BIT #) f (FILE #) 0 b = 3-bit bit address f = 7-bit file register address Literal and control operations General 13 OPCODE 8 7 0 k (literal) k = 8-bit immediate value CALL and GOTO instructions only 13 11 10 OPCODE 0 k (literal)
PIC12(L)F1840 TABLE 29-3: PIC12F/LF1840 INSTRUCTION SET Mnemonic, Operands Description Cycles 14-Bit Opcode MSb LSb Status Affected Notes BYTE-ORIENTED FILE REGISTER OPERATIONS ADDWF ADDWFC ANDWF ASRF LSLF LSRF CLRF CLRW COMF DECF INCF IORWF MOVF MOVWF RLF RRF SUBWF SUBWFB SWAPF XORWF f, d f, d f, d f, d f, d f, d f – f, d f, d f, d f, d f, d f f, d f, d f, d f, d f, d f, d Add W and f Add with Carry W and f AND W with f Arithmetic Right Shift Logical Left Shift Logical Right Shift Clear f Clear
PIC12(L)F1840 TABLE 29-3: PIC12F/LF1840 INSTRUCTION SET (CONTINUED) Mnemonic, Operands Description Cycles 14-Bit Opcode MSb LSb Status Affected Notes CONTROL OPERATIONS 2 2 2 2 2 2 2 2 BRA BRW CALL CALLW GOTO RETFIE RETLW RETURN k – k – k k k – Relative Branch Relative Branch with W Call Subroutine Call Subroutine with W Go to address Return from interrupt Return with literal in W Return from Subroutine CLRWDT NOP OPTION RESET SLEEP TRIS – – – – – f Clear Watchdog Timer No Operation Load OPT
PIC12(L)F1840 29.2 Instruction Descriptions ADDFSR Add Literal to FSRn ANDLW AND literal with W Syntax: [ label ] ADDFSR FSRn, k Syntax: [ label ] ANDLW Operands: -32 k 31 n [ 0, 1] Operands: 0 k 255 Operation: FSR(n) + k FSR(n) Status Affected: None Description: The signed 6-bit literal ‘k’ is added to the contents of the FSRnH:FSRnL register pair. k Operation: (W) .AND.
PIC12(L)F1840 BCF Bit Clear f Syntax: [ label ] BCF BTFSC f,b Bit Test f, Skip if Clear Syntax: [ label ] BTFSC f,b 0 f 127 0b7 Operands: 0 f 127 0b7 Operands: Operation: 0 (f) Operation: skip if (f) = 0 Status Affected: None Status Affected: None Description: Bit ‘b’ in register ‘f’ is cleared. Description: If bit ‘b’ in register ‘f’ is ‘1’, the next instruction is executed.
PIC12(L)F1840 CALL Call Subroutine CLRWDT Clear Watchdog Timer Syntax: [ label ] CALL k Syntax: [ label ] CLRWDT Operands: 0 k 2047 Operands: None Operation: (PC)+ 1 TOS, k PC<10:0>, (PCLATH<6:3>) PC<14:11> Operation: Status Affected: None 00h WDT 0 WDT prescaler, 1 TO 1 PD Description: Call Subroutine. First, return address (PC + 1) is pushed onto the stack. The eleven-bit immediate address is loaded into PC bits <10:0>. The upper bits of the PC are loaded from PCLATH.
PIC12(L)F1840 DECFSZ Decrement f, Skip if 0 INCFSZ Increment f, Skip if 0 Syntax: [ label ] DECFSZ f,d Syntax: [ label ] Operands: 0 f 127 d [0,1] Operands: 0 f 127 d [0,1] Operation: (f) - 1 (destination); skip if result = 0 Operation: (f) + 1 (destination), skip if result = 0 Status Affected: None Status Affected: None Description: The contents of register ‘f’ are decremented. If ‘d’ is ‘0’, the result is placed in the W register.
PIC12(L)F1840 LSLF Logical Left Shift MOVF f {,d} Move f Syntax: [ label ] LSLF Syntax: [ label ] Operands: 0 f 127 d [0,1] Operands: 0 f 127 d [0,1] Operation: (f<7>) C (f<6:0>) dest<7:1> 0 dest<0> Operation: (f) (dest) Status Affected: C, Z Description: The contents of register ‘f’ are shifted one bit to the left through the Carry flag. A ‘0’ is shifted into the LSb. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’.
PIC12(L)F1840 MOVIW Move INDFn to W Syntax: [ label ] MOVIW ++FSRn [ label ] MOVIW --FSRn [ label ] MOVIW FSRn++ [ label ] MOVIW FSRn-[ label ] MOVIW k[FSRn] Operands: n [0,1] mm [00,01, 10, 11] -32 k 31 Operation: INDFn W Effective address is determined by • FSR + 1 (preincrement) • FSR - 1 (predecrement) • FSR + k (relative offset) After the Move, the FSR value will be either: • FSR + 1 (all increments) • FSR - 1 (all decrements) • Unchanged Status Affected: MOVLP Syntax: [ label ] MOV
PIC12(L)F1840 NOP MOVWI Move W to INDFn Syntax: [ label ] MOVWI ++FSRn [ label ] MOVWI --FSRn [ label ] MOVWI FSRn++ [ label ] MOVWI FSRn-[ label ] MOVWI k[FSRn] Operands: Operation: Status Affected: n [0,1] mm [00,01, 10, 11] -32 k 31 W INDFn Effective address is determined by • FSR + 1 (preincrement) • FSR - 1 (predecrement) • FSR + k (relative offset) After the Move, the FSR value will be either: • FSR + 1 (all increments) • FSR - 1 (all decrements) Unchanged None Syntax: [ label ] O
PIC12(L)F1840 RETFIE Return from Interrupt Syntax: [ label ] RETFIE RETURN Return from Subroutine Syntax: [ label ] None RETURN Operands: None Operands: Operation: TOS PC, 1 GIE Operation: TOS PC Status Affected: None Status Affected: None Description: Description: Return from Interrupt. Stack is POPed and Top-of-Stack (TOS) is loaded in the PC. Interrupts are enabled by setting Global Interrupt Enable bit, GIE (INTCON<7>). This is a two-cycle instruction.
PIC12(L)F1840 SUBLW Subtract W from literal Syntax: [ label ] RRF Rotate Right f through Carry Syntax: [ label ] Operands: 0 f 127 d [0,1] Operands: 0 k 255 Operation: k - (W) W) Operation: See description below Status Affected: C, DC, Z Status Affected: C Description: Description: The contents of register ‘f’ are rotated one bit to the right through the Carry flag. If ‘d’ is ‘0’, the result is placed in the W register.
PIC12(L)F1840 SWAPF Swap Nibbles in f XORLW Exclusive OR literal with W Syntax: [ label ] Syntax: [ label ] Operands: 0 f 127 d [0,1] Operation: SWAPF f,d (f<3:0>) (destination<7:4>), (f<7:4>) (destination<3:0>) XORLW k Operands: 0 k 255 Operation: (W) .XOR. k W) Status Affected: Z Description: The contents of the W register are XOR’ed with the eight-bit literal ‘k’. The result is placed in the W register.
PIC12(L)F1840 30.0 ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings(†) Ambient temperature under bias....................................................................................................... -40°C to +125°C Storage temperature ........................................................................................................................ -65°C to +150°C Voltage on VDD with respect to VSS, PIC12F1840 ............................................................................. -0.
PIC12(L)F1840 PIC12F1840 VOLTAGE FREQUENCY GRAPH, -40°C TA +125°C FIGURE 30-1: VDD (V) 5.5 2.5 2.3 1.8 4 0 10 16 32 Frequency (MHz) Note 1: The shaded region indicates the permissible combinations of voltage and frequency. 2: Refer to Table 30-1 for each Oscillator mode’s supported frequencies. PIC12LF1840 VOLTAGE FREQUENCY GRAPH, -40°C TA +125°C VDD (V) FIGURE 30-2: 3.6 2.5 1.
PIC12(L)F1840 FIGURE 30-3: HFINTOSC FREQUENCY ACCURACY OVER DEVICE VDD AND TEMPERATURE 125 ± 5% Temperature (°C) 85 ± 3% 60 25 ± 2% 0 ± 5% -40 1.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V) 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 30.1 DC Characteristics: Supply Voltage PIC12LF1840 Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended PIC12F1840 Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended Param. No. D001 Sym. VDD Characteristic Min. Typ† Max. Units 1.8 2.5 — — 3.6 3.6 V V FOSC 16 MHz: FOSC 32 MHz 2.3 2.
PIC12(L)F1840 FIGURE 30-4: POR AND POR REARM WITH SLOW RISING VDD VDD VPOR VPORR VSS NPOR(1) POR REARM VSS TVLOW(2) Note 1: 2: 3: TPOR(3) When NPOR is low, the device is held in Reset. TPOR 1 s typical. TVLOW 2.7 s typical. 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 30.2 DC Characteristics: Supply Current (IDD) PIC12LF1840 Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended PIC12F1840 Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended Param No. Device Characteristics Conditions Min. Typ† Max. Units — 5.0 12 A 1.8 — 7.4 25 A 3.0 — 17 28 A 2.
PIC12(L)F1840 30.2 DC Characteristics: Supply Current (IDD) (Continued) PIC12LF1840 Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended PIC12F1840 Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended Param No. Device Characteristics Min. Typ† Max.
PIC12(L)F1840 30.2 DC Characteristics: Supply Current (IDD) (Continued) PIC12LF1840 Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended PIC12F1840 Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended Param No. Device Characteristics Max. Units Conditions Min. Typ† — 1.3 3.0 mA 3.0 — 2.3 4.0 mA 3.6 — 2.
PIC12(L)F1840 30.3 DC Characteristics: Power-Down Base Current (IPD) PIC12LF1840 Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended PIC12F1840 Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended Param No. Device Characteristics Power-down Base Current D022 D022 D023 D023 Conditions Typ† Max. +85°C Max.
PIC12(L)F1840 30.3 DC Characteristics: Power-Down Base Current (IPD) (Continued) PIC12LF1840 Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended PIC12F1840 Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended Param No. Device Characteristics Max. +85°C Max. +125°C Units — 250 — — A 1.8 — 250 — — A 3.
PIC12(L)F1840 30.4 DC Characteristics: I/O Ports DC CHARACTERISTICS Param No. Sym. VIL Characteristic Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended Min. Typ† Max. Units Conditions Input Low Voltage I/O PORT: D030 — — 0.8 V 4.5V VDD 5.5V — — 0.15 VDD V 1.8V VDD 4.5V with Schmitt Trigger buffer — — 0.2 VDD V 2.0V VDD 5.5V with I2C™ levels — — 0.
PIC12(L)F1840 30.4 DC Characteristics: I/O Ports (Continued) DC CHARACTERISTICS Param No. Sym. Characteristic Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended Min. Typ† Max.
PIC12(L)F1840 30.5 Memory Programming Requirements Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +85°C for industrial -40°C TA +125°C for extended DC CHARACTERISTICS Param No. Sym. Characteristic Min. Typ† Max. Units Conditions Program Memory Programming Specifications D110 VIHH Voltage on MCLR/VPP pin 8.0 — 9.0 V D111 IDDP Supply Current during Programming — — 10 mA D112 VBE VDD for Bulk Erase 2.
PIC12(L)F1840 30.6 Thermal Considerations Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +125°C Param No. TH01 TH02 Sym. Characteristic Typ. Units JA Thermal Resistance Junction to Ambient 56.7 C/W 89.3 C/W 8-pin PDIP package 149.
PIC12(L)F1840 30.7 Timing Parameter Symbology The timing parameter symbols have been created with one of the following formats: 1. TppS2ppS 2.
PIC12(L)F1840 30.8 AC Characteristics: PIC12(L)F1840-I/E FIGURE 30-6: CLOCK TIMING Q4 Q1 Q2 Q3 Q4 Q1 OSC1/CLKIN OS02 OS04 OS04 OS03 OSC2/CLKOUT (LP,XT,HS Modes) OSC2/CLKOUT (CLKOUT Mode) TABLE 30-1: CLOCK OSCILLATOR TIMING REQUIREMENTS Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +125°C Param No. OS01 Sym.
PIC12(L)F1840 TABLE 30-2: OSCILLATOR PARAMETERS Standard Operating Conditions (unless otherwise stated) Operating Temperature -40°C TA +125°C Param No. OS08 Sym. HFOSC OS08A MFOSC Characteristic Internal Calibrated HFINTOSC Frequency (Note 1) Internal Calibrated MFINTOSC Frequency (Note 1) Freq. Tolerance Min. Typ† Max. Units Conditions 2% — 16.0 — MHz 0°C TA +60°C, VDD 2.5V 3% — 16.0 — MHz 60°C TA +85°C, VDD 2.5V 5% — 16.
PIC12(L)F1840 FIGURE 30-7: CLKOUT AND I/O TIMING Cycle Write Fetch Read Execute Q4 Q1 Q2 Q3 FOSC OS12 OS11 OS20 OS21 CLKOUT OS19 OS18 OS16 OS13 OS17 I/O pin (Input) OS14 OS15 I/O pin (Output) New Value Old Value OS18, OS19 TABLE 30-4: CLKOUT AND I/O TIMING PARAMETERS Standard Operating Conditions (unless otherwise stated) Operating Temperature -40°C TA +125°C Param No. Sym. Characteristic Min. Typ† Max.
PIC12(L)F1840 FIGURE 30-8: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING VDD MCLR 30 Internal POR 33 PWRT Time-out 32 OSC Start-Up Time Internal Reset(1) Watchdog Timer Reset(1) 31 34 34 I/O pins Note 1: Asserted low.
PIC12(L)F1840 TABLE 30-5: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER AND BROWN-OUT RESET PARAMETERS Standard Operating Conditions (unless otherwise stated) Operating Temperature -40°C TA +125°C Param No. Sym. Characteristic Min. Typ† Max. Units Conditions 2 — — s 10 16 27 ms Oscillator Start-up Timer Period (Note 1) — 1024 — Tosc TPWRT Power-up Timer Period, PWRTE = 0 40 65 140 ms TIOZ I/O high-impedance from MCLR Low or Watchdog Timer Reset — — 2.
PIC12(L)F1840 FIGURE 30-10: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS T0CKI 40 41 42 T1CKI 45 46 49 47 TMR0 or TMR1 TABLE 30-6: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS Standard Operating Conditions (unless otherwise stated) Operating Temperature -40°C TA +125°C Param No. 40* Sym. TT0H Characteristic T0CKI High Pulse Width Min.
PIC12(L)F1840 FIGURE 30-11: CAPTURE/COMPARE/PWM TIMINGS (CCP) CCP (Capture mode) CC01 CC02 CC03 Note: Refer to Figure 30-5 for load conditions. TABLE 30-7: CAPTURE/COMPARE/PWM REQUIREMENTS (CCP) Standard Operating Conditions (unless otherwise stated) Operating Temperature -40°C TA +125°C Param Sym. No. Characteristic CC01* TccL CCP Input Low Time CC02* TccH CCP Input High Time CC03* TccP * † Min. Typ† Max. Units 0.5TCY + 20 — — ns With Prescaler 20 — — ns No Prescaler 0.
PIC12(L)F1840 TABLE 30-9: ADC CONVERSION REQUIREMENTS Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C TA +125°C Param No. Sym. Characteristic AD130* TAD AD131 TCNV AD132* TACQ Min. Typ† Max. Units Conditions ADC Clock Period 1.0 — 9.0 s FOSC-based ADC Internal RC Oscillator Period 1.0 2.0 6.
PIC12(L)F1840 FIGURE 30-13: ADC CONVERSION TIMING (SLEEP MODE) BSF ADCON0, GO AD134 (TOSC/2 + TCY(1)) 1 TCY AD131 Q4 AD130 ADC CLK 7 ADC Data 6 5 4 OLD_DATA ADRES 3 2 1 0 NEW_DATA ADIF 1 TCY GO DONE Sample AD132 Sampling Stopped Note 1: If the ADC clock source is selected as RC, a time of TCY is added before the ADC clock starts. This allows the SLEEP instruction to be executed. DS40001441D-page 336 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 TABLE 30-10: COMPARATOR SPECIFICATIONS Operating Conditions: 1.8V < VDD < 5.5V, -40°C < TA < +125°C (unless otherwise stated). Param No. Sym. Characteristics Min. Typ. Max. Units — ±7.
PIC12(L)F1840 FIGURE 30-14: USART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING CK US121 US121 DT US122 US120 Note: Refer to Figure 30-5 for load conditions. TABLE 30-12: USART SYNCHRONOUS TRANSMISSION REQUIREMENTS Standard Operating Conditions (unless otherwise stated) Operating Temperature -40°C TA +125°C Param. No. Symbol Characteristic Min. Max. Units US120 TCKH2DTV SYNC XMIT (Master and Slave) Clock high to data-out valid 3.0-5.5V — 80 ns 1.8-5.
PIC12(L)F1840 FIGURE 30-16: SPI MASTER MODE TIMING (CKE = 0, SMP = 0) SSx SP70 SCKx (CKP = 0) SP71 SP72 SP78 SP79 SP79 SP78 SCKx (CKP = 1) SP80 bit 6 - - - - - -1 MSb SDOx LSb SP75, SP76 SDIx MSb In bit 6 - - - -1 LSb In SP74 SP73 Note: Refer to Figure 30-5 for load conditions.
PIC12(L)F1840 FIGURE 30-18: SPI SLAVE MODE TIMING (CKE = 0) SSx SP70 SCKx (CKP = 0) SP83 SP71 SP72 SP78 SP79 SP79 SP78 SCKx (CKP = 1) SP80 MSb SDOx LSb bit 6 - - - - - -1 SP77 SP75, SP76 SDIx MSb In bit 6 - - - -1 LSb In SP74 SP73 Note: Refer to Figure 30-5 for load conditions.
PIC12(L)F1840 TABLE 30-14: SPI MODE REQUIREMENTS Param No. Symbol Characteristic SP70* TSSL2SCH, SS to SCK or SCK input TSSL2SCL Min. Typ† Max. Units Conditions TCY — — ns SP71* TSCH SCK input high time (Slave mode) TCY + 20 — — ns SP72* TSCL SCK input low time (Slave mode) TCY + 20 — — ns 100 — — ns 100 — — ns 3.0-5.5V — 10 25 ns 1.8-5.
PIC12(L)F1840 I2C™ BUS START/STOP BITS TIMING FIGURE 30-20: SCLx SP93 SP91 SP90 SP92 SDAx Stop Condition Start Condition Note: Refer to Figure 30-5 for load conditions. TABLE 30-15: I2C™ BUS START/STOP BITS REQUIREMENTS Param. No. Symbol SP90* TSU:STA SP91* THD:STA SP92* TSU:STO SP93* THD:STO Characteristic Start condition 100 kHz mode Min. Typ. Max.
PIC12(L)F1840 FIGURE 30-21: I2C™ BUS DATA TIMING SP100 SP103 SCLx SP102 SP101 SP90 SP106 SP107 SP92 SP91 SDAx In SP110 SP109 SP109 SDAx Out Note: Refer to Figure 30-5 for load conditions. I TABLE 30-16: I2C™ BUS DATA REQUIREMENTS Param. No. SP100* Symbol THIGH Characteristic Clock high time Min. Max. Units 100 kHz mode 4.0 — s Device must operate at a minimum of 1.5 MHz 400 kHz mode 0.6 — s Device must operate at a minimum of 10 MHz 1.5TCY — — 100 kHz mode 4.
PIC12(L)F1840 TABLE 30-17: CAP SENSE OSCILLATOR SPECIFICATIONS Param. No. Symbol CS01* ISRC CS02* ISNK Characteristic Current Source Current Sink Min. Typ† Max. Units High — -8 — A Medium — -1.5 — A Low — -0.3 — A High — 7.5 — A Medium — 1.5 — A — 0.25 — A — 0.8 — V Low CS03* VCTH Cap Threshold CS04* VCTL Cap Threshold CS05* VCHYST Cap Hysteresis (VCTH - VCTL) — 0.
PIC12(L)F1840 31.0 DC AND AC CHARACTERISTICS GRAPHS AND CHARTS The graphs and tables provided in this section are for design guidance and are not tested. In some graphs or tables, the data presented are outside specified operating range (i.e., outside specified VDD range). This is for information only and devices are ensured to operate properly only within the specified range.
PIC12(L)F1840 FIGURE 31-1: IDD, LP OSCILLATOR, FOSC = 32 kHz, PIC12LF1840 ONLY 25 IDD (μA) Max. Max: 85°C + 3ı Typical: 25°C 20 15 10 Typical 5 0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) IDD, LP OSCILLATOR, FOSC = 32 kHz, PIC12F1840 ONLY FIGURE 31-2: 40 Max: 85°C + 3ı Typical: 25°C 35 Max. 30 IDD (μA) 25 Typical 20 15 10 5 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) DS40001441D-page 346 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-3: IDD TYPICAL, XT AND EXTRC OSCILLATOR, PIC12LF1840 ONLY 500 Typical: 25°C 450 4 MHz EXTRC 400 IDD (μA) 350 4 MHz XT 300 250 200 1 MHz XT 150 100 50 0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 3.6 3.8 VDD (V) FIGURE 31-4: IDD MAXIMUM, XT AND EXTRC OSCILLATOR, PIC12LF1840 ONLY 600 Max: 85°C + 3ı 500 4 MHz EXTRC 4 MHz XT IDD (μA) 400 300 1 MHz XT 200 100 0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.
PIC12(L)F1840 FIGURE 31-5: IDD TYPICAL, XT AND EXTRC OSCILLATOR, PIC12F1840 ONLY 4 MHz EXTRC Typical: 25°C 500 4 MHz XT IDD (μA) 400 300 1 MHz XT 200 100 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) IDD MAXIMUM, XT AND EXTRC OSCILLATOR, PIC12F1840 ONLY FIGURE 31-6: 600 Max: 85°C + 3ı 4 MHz EXTRC 500 4 MHz XT 400 IDD (μA) 1 MHz XT 300 200 100 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) DS40001441D-page 348 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-7: IDD, EXTERNAL CLOCK (ECL), LOW-POWER MODE, FOSC = 32 kHz, PIC12LF1840 ONLY 16 Max: 85°C + 3ı Typical: 25°C 14 Max. 12 IDD (μA) 10 8 Typical 6 4 2 0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) FIGURE 31-8: IDD, EXTERNAL CLOCK (ECL), LOW-POWER MODE, FOSC = 32 kHz, PIC12F1840 ONLY 40 Max: 85°C + 3ı Typical: 25°C 35 Max. IDD (μA) 30 Typical 25 20 15 10 5 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.
PIC12(L)F1840 FIGURE 31-9: IDD, EXTERNAL CLOCK (ECL), LOW-POWER MODE, FOSC = 500 kHz, PIC12LF1840 ONLY 70 Max: 85°C + 3ı Typical: 25°C 60 Max. IDD (μA) 50 Typical 40 30 20 10 0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) FIGURE 31-10: IDD, EXTERNAL CLOCK (ECL), LOW-POWER MODE, FOSC = 500 kHz, PIC12F1840 ONLY 70 60 Max. IDD (μA) 50 40 Typical 30 20 Max: 85°C + 3ı Typical: 25°C 10 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.
PIC12(L)F1840 FIGURE 31-11: IDD TYPICAL, EXTERNAL CLOCK (ECM), MEDIUM-POWER MODE, PIC12LF1840 ONLY 350 Typical: 25°C 300 4 MHz IDD (μA) 250 200 150 100 1 MHz 50 0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) FIGURE 31-12: IDD MAXIMUM, EXTERNAL CLOCK (ECM), MEDIUM-POWER MODE, PIC12LF1840 ONLY 400 350 Max: 85°C + 3ı 4 MHz 300 IDD (μA) 250 200 150 1 MHz 100 50 0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-13: IDD TYPICAL, EXTERNAL CLOCK (ECM), MEDIUM-POWER MODE, PIC12F1840 ONLY 400 4 MHz Typical: 25°C 350 IDD (μA) 300 250 200 1 MHz 150 100 50 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) FIGURE 31-14: IDD MAXIMUM, EXTERNAL CLOCK (ECM), MEDIUM-POWER MODE, PIC12F1840 ONLY 450 400 4 MHz Max: 85°C + 3ı 350 IDD (μA) 300 250 200 1 MHz 150 100 50 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) DS40001441D-page 352 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-15: IDD TYPICAL, EXTERNAL CLOCK (ECH), HIGH-POWER MODE, PIC12LF1840 ONLY 2.5 Typical: 25°C 32 MHz IDD (mA) 2.0 1.5 16 MHz 1.0 8 MHz 0.5 0.0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 3.6 3.8 VDD (V) FIGURE 31-16: IDD MAXIMUM, EXTERNAL CLOCK (ECH), HIGH-POWER MODE, PIC12LF1840 ONLY 3.0 Max: 85°C + 3ı 2.5 32 MHz IDD (mA) 2.0 1.5 16 MHz 1.0 8 MHz 0.5 0.0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 VDD (V) 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-17: IDD TYPICAL, EXTERNAL CLOCK (ECH), HIGH-POWER MODE, PIC12F1840 ONLY 2.5 Typical: 25°C 32 MHz 2.0 IDD (mA) 1.5 16 MHz 1.0 8 MHz 0.5 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 5.5 6.0 VDD (V) FIGURE 31-18: IDD MAXIMUM, EXTERNAL CLOCK (ECH), HIGH-POWER MODE, PIC12F1840 ONLY 2.5 Max: 85°C + 3ı 32 MHz 2.0 IDD (mA) 16 MHz 1.5 8 MHz 1.0 0.5 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 VDD (V) DS40001441D-page 354 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-19: IDD, LFINTOSC, FOSC = 31 kHz, PIC12LF1840 ONLY 30 Max. Max: 85°C + 3ı Typical: 25°C 25 IDD (μA) 20 15 Typical 10 5 0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) FIGURE 31-20: IDD, LFINTOSC, FOSC = 31 kHz, PIC12F1840 ONLY 35 Max. 30 Typical IDD (μA) 25 20 15 10 Max: 85°C + 3ı Typical: 25°C 5 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-21: IDD, MFINTOSC, FOSC = 500 kHz, PIC12LF1840 ONLY 200 180 Max: 85°C + 3ı Typical: 25°C 160 Max. Typical IDD (μA) 140 120 100 80 60 40 20 0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) FIGURE 31-22: IDD, MFINTOSC, FOSC = 500 kHz, PIC12F1840 ONLY 300 Max. Max: 85°C + 3ı Typical: 25°C 250 Typical IDD (μA) 200 150 100 50 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) DS40001441D-page 356 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-23: IDD TYPICAL, HFINTOSC, PIC12LF1840 ONLY 3.0 Typical: 25°C 2.5 32 MHz (4x PLL) IDD (mA) 2.0 1.5 16 MHz 8 MHz 1.0 4 MHz 0.5 0.0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) FIGURE 31-24: IDD MAXIMUM, HFINTOSC, PIC12LF1840 ONLY 5.0 Max: 85°C + 3ı 4.5 4.0 IDD (mA) 3.5 32 MHz (4x PLL) 3.0 2.5 2.0 16 MHz 8 MHz 1.5 4 MHz 1.0 0.5 0.0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-25: IDD TYPICAL, HFINTOSC, PIC12F1840 ONLY 3.0 32 MHz (4x PLL) Typical: 25°C 2.5 IDD (mA) 2.0 1.5 16 MHz 8 MHz 1.0 4 MHz 0.5 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) IDD MAXIMUM, HFINTOSC, PIC12F1840 ONLY FIGURE 31-26: 4.5 32 MHz (4x PLL) Max: 85°C + 3ı 4.0 3.5 IDD (mA) 3.0 2.5 16 MHz 2.0 8 MHz 1.5 1.0 4 MHz 0.5 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) DS40001441D-page 358 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-27: IDD TYPICAL, HS OSCILLATOR, PIC12LF1840 ONLY 1.8 32 MHz Typical: 25°C 1.6 1.4 IDD (mA) 1.2 1.0 8 MHz 0.8 0.6 4 MHz 0.4 0.2 0.0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) FIGURE 31-28: IDD MAXIMUM, HS OSCILLATOR, PIC12LF1840 ONLY 2.5 Max: 85°C + 3ı 32 MHz 2.0 IDD (mA) 1.5 8 MHz 1.0 4 MHz 0.5 0.0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-29: IDD TYPICAL, HS OSCILLATOR, PIC12F1840 ONLY 2.0 1.8 32 MHz Typical: 25°C 1.6 1.4 IDD (mA) 1.2 1.0 8 MHz 0.8 4 MHz 0.6 0.4 0.2 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) IDD MAXIMUM, HS OSCILLATOR, PIC12F1840 ONLY FIGURE 31-30: 2.5 32 MHz Max: 85°C + 3ı 2.0 IDD (mA) 1.5 8 MHz 1.0 4 MHz 0.5 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) DS40001441D-page 360 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-31: IPD BASE, SLEEP MODE, PIC12LF1840 ONLY 450 Max: 85°C + 3 M 3ı Typical: 25°C 400 Max. 350 IPD D (nA) 300 250 200 150 100 Typical 50 0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) FIGURE 31-32: IPD BASE, LOW-POWER SLEEP MODE, VREGPM = 1, PIC12F1840 ONLY 600 Max. Max: 85°C + 3ı Typical: 25°C 500 IPD (nA) 400 300 Typical 200 100 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-33: IPD, WATCHDOG TIMER (WDT), PIC12LF1840 ONLY 1.4 Max: 85°C + 3ı Typical: 25°C 1.2 Max. IPD (μA (μA) 1.0 0 8 0.8 Typical 0.6 0.4 0.2 0.0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) FIGURE 31-34: IPD, WATCHDOG TIMER (WDT), PIC12F1840 ONLY 1.2 Max: 85°C + 3ı Typical: 25°C 1.0 Max. IPD (μA A) 0.8 Typical 0.6 0.4 0.2 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) DS40001441D-page 362 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-35: IPD, FIXED VOLTAGE REFERENCE (FVR), PIC12LF1840 ONLY 25 Max. Typical 20 IPD (μA A) 15 10 Max: 85°C + 3ı Typical: 25°C 5 0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) FIGURE 31-36: IPD, FIXED VOLTAGE REFERENCE (FVR), PIC12F1840 ONLY 30 Max. 25 IPD (μA) 20 Typical 15 10 Max: 85°C + 3ı Typical: 25°C 5 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-37: IPD, BROWN-OUT RESET (BOR), BORV = 1, PIC12LF1840 ONLY 12 Max. Max: 85°C + 3ı Typical: 25°C 10 8 IPD D (μA) Typical 6 4 2 0 16 1.6 1 8 1.8 2 0 2.0 2 2 2.2 2 4 2.4 2 6 2.6 2 8 2.8 3 0 3.0 3 2 3.2 3 4 3.4 3 6 3.6 3 8 3.8 VDD (V) IPD, BROWN-OUT RESET (BOR), BORV = 1, PIC12F1840 ONLY FIGURE 31-38: 14 Max Max. Max: 85°C + 3ı Ma Typical: 25°C 12 IPD (μA) 10 Typical 8 6 4 2 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.
PIC12(L)F1840 FIGURE 31-39: IPD, TIMER1 OSCILLATOR, FOSC = 32 kHz, PIC12LF1840 ONLY 6.0 Max: 85°C + 3ı Typical: 25°C 5.0 Max. IPD (μA A) 4.0 3.0 Typical 2.0 1.0 0.0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) FIGURE 31-40: IPD, TIMER1 OSCILLATOR, FOSC = 32 kHz, PIC12F1840 ONLY 12 Max: 85°C + 3ı Typical: 25°C 10 Max. IPD (μA) 8 Typical 6 4 2 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-41: VOH vs. IOH OVER TEMPERATURE, VDD = 5.5V, PIC12F1840 ONLY 6 5 VOH (V) 4 3 125°C Typical 2 -40°C Graph represents 3ı Limits 1 0 -45 -40 -35 -30 -25 -20 -15 -10 -5 0 IOH (mA) VOL vs. IOL OVER TEMPERATURE, VDD = 5.5V, PIC12F1840 ONLY FIGURE 31-42: 5 4 VOL (V) 125°C Graph represents 3ı Limits 3 Typical 2 -40°C 1 0 0 10 DS40001441D-page 366 20 30 40 50 IOL (mA) 60 70 80 90 100 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-43: VOH vs. IOH OVER TEMPERATURE, VDD = 3.0V 3.5 Graph represents 3ı Limits 3.0 VOH (V) 2.5 2.0 125°C 1.5 Typical 1.0 -40°C 0.5 0.0 -15 -13 -11 -9 -7 -5 -3 -1 IOH (mA) FIGURE 31-44: VOL vs. IOL, OVER TEMPERATURE, VDD = 3.0V 3.0 125°C Graph represents 3ı Limits 2.5 Typical VOL (V) 2.0 -40°C 1.5 1.0 0.5 0.0 0 5 10 15 20 25 30 35 40 IOL (mA) 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-45: VOH vs. IOH OVER TEMPERATURE, VDD = 1.8V, PIC12LF1840 ONLY 2.0 Graph represents 3ı Limits 1.8 1.6 VOH (V) 1.4 125°C 1.2 1.0 Typical 0.8 0.6 -40°C 0.4 0.2 0.0 -4.5 -4.0 -3.5 -3.0 -2.5 -2.0 -1.5 -1.0 -0.5 0.0 IOH (mA) VOL vs. IOL OVER TEMPERATURE, VDD = 1.8V, PIC12LF1840 ONLY FIGURE 31-46: 1.8 Graph represents 3ı Limits 1.6 1.4 125°C 1.2 VOL (V) Typical 1.0 -40°C 0.8 0.6 0.4 0.2 0.
PIC12(L)F1840 FIGURE 31-47: POR RELEASE VOLTAGE 1.70 1.68 Max. 1.66 Voltage (V) 1.64 Typical 1.62 Min. 1.60 1.58 1.56 Max: Typical + 3ı Typical: 25°C Min: Typical - 3ı 1.54 1.52 1.50 -60 -40 -20 0 20 40 60 80 100 120 140 120 140 Temperature (°C) FIGURE 31-48: POR REARM VOLTAGE, PIC12F1840 ONLY 1.54 Max: Typical + 3ı Typical: 25°C Min: Typical - 3ı 1.52 1.50 Max. Voltage (V) 1.48 1.46 1.44 Typical 1.42 1.40 Min. 1.38 1.36 1.
PIC12(L)F1840 FIGURE 31-49: BROWN-OUT RESET VOLTAGE, BORV = 1, PIC12LF1840 ONLY 2.00 Max. Voltage (V) 1.95 Typical 1.90 1.85 Min. Max: Typical + 3ı Min: Typical - 3ı 1.80 -60 -40 -20 0 20 40 60 80 100 120 140 Temperature (°C) FIGURE 31-50: BROWN-OUT RESET HYSTERESIS, BORV = 1, PIC12LF1840 ONLY 60 50 Max. Max: Typical + 3ı Typical: 25°C Min: Typical - 3ı Voltage (mV) 40 Typical 30 20 Min.
PIC12(L)F1840 FIGURE 31-51: BROWN-OUT RESET VOLTAGE, BORV = 1, PIC12F1840 ONLY 2.60 Max. 2.55 Voltage (V) 2.50 Typical 2.45 Min. 2.40 Max: Typical + 3ı Min: Typical - 3ı 2.35 2.30 -60 -40 -20 0 20 40 60 80 100 120 140 120 140 Temperature (°C) FIGURE 31-52: BROWN-OUT RESET HYSTERESIS, BORV = 1, PIC12F1840 ONLY 70 Max. 60 Max: Typical + 3ı Typical: 25°C Min: Typical - 3ı Voltage (mV) 50 40 Typical 30 20 Min.
PIC12(L)F1840 FIGURE 31-53: BROWN-OUT RESET VOLTAGE, BORV = 0 2.80 2.75 Voltage (V) Max. 2.70 Typical 2.65 Min. Max: Typical + 3ı Min: Typical - 3ı 2.60 2.55 -60 -40 -20 0 20 40 60 80 100 120 140 120 140 Temperature (°C) FIGURE 31-54: BROWN-OUT RESET HYSTERESIS, BORV = 0 90 80 Min. 70 Voltage (mV) 60 Typical 50 40 Max: Typical + 3ı Typical: 25°C Min: Typical - 3ı 30 20 Max.
PIC12(L)F1840 FIGURE 31-55: LOW POWER BROWN-OUT RESET VOLTAGE, LPBOR = 0 2.50 Max. Max: Typical + 3ı Min: Typical - 3ı 2.40 Voltage (V) 2.30 Typical 2.20 2.10 2.00 Min. 1.90 1.80 -60 -40 -20 0 20 40 60 80 100 120 140 120 140 Temperature (°C) FIGURE 31-56: LOW POWER BROWN-OUT RESET HYSTERESIS, LPBOR = 0 45 Max: Typical + 3ı Typical: 25°C Min: Typical - 3ı 40 35 Max. Typical Voltage (mV) 30 25 Min.
PIC12(L)F1840 FIGURE 31-57: WDT TIME-OUT PERIOD 24 22 Max. Time (ms) 20 18 Typical 16 Min. 14 Max: Typical + 3ı (-40°C to +125°C) Typical: statistical mean @ 25°C Min: Typical - 3ı (-40°C to +125°C) 12 10 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 5.0 5.5 6.0 VDD (V) FIGURE 31-58: PWRT PERIOD 100 Max: Typical + 3ı (-40°C to +125°C) Typical: statistical mean @ 25°C Min: Typical - 3ı (-40°C to +125°C) 90 Max. Time (ms) 80 70 Typical 60 Min. 50 40 1.5 2.0 2.5 3.0 3.5 4.0 4.
PIC12(L)F1840 FIGURE 31-59: FVR STABILIZATION PERIOD 40 35 Max: Typical + 3ı Typical: statistical mean @ 25°C Max. Time (us) 30 Typical 25 20 15 Note: The FVR Stabilization Period applies when: 1) coming out of RESET or exiting Sleep mode for PIC12/16LFxxxx devices. 2) when exiting sleep mode with VREGPM = 1 for PIC12/16Fxxxx devices In all other cases, the FVR is stable when released from RESET. 10 5 0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.
PIC12(L)F1840 FIGURE 31-60: COMPARATOR HYSTERESIS, NORMAL-POWER MODE, CxSP = 1, CxHYS = 1 80 70 Max. Hysteresis (mV) 60 Typical 50 40 Min. 30 20 Max: Typical + 3ı Typical: 25°C Min: Typical - 3ı 10 0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) FIGURE 31-61: COMPARATOR HYSTERESIS, LOW-POWER MODE, CxSP = 0, CxHYS = 1 16 14 Max. Hysteresis (mV) 12 Typical 10 8 6 Min. 4 Max: Typical + 3ı Typical: 25°C Min: Typical - 3ı 2 0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.
PIC12(L)F1840 FIGURE 31-62: COMPARATOR RESPONSE TIME, NORMAL-POWER MODE, CxSP = 1 350 300 Time (ns) 250 Max. 200 Typical 150 100 Max: Typical + 3ı Typical: 25°C 50 0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) FIGURE 31-63: COMPARATOR RESPONSE TIME OVER TEMPERATURE, NORMAL-POWER MODE, CxSP = 1 400 Graph represents 3ı Limits 350 Time (ns) 300 250 125°C 200 150 Typical 100 -40°C 50 0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-64: COMPARATOR INPUT OFFSET AT 25°C, NORMAL-POWER MODE, CxSP = 1, PIC12F1840 ONLY 50 40 30 Max. Offset Voltage (mV) 20 10 Typical 0 Min. -10 -20 Max: Typical + 3ı Typical: 25°C Min: Typical - 3ı -30 -40 -50 0.0 1.0 2.0 3.0 4.0 5.0 Common Mode Voltage (V) DS40001441D-page 378 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 FIGURE 31-65: LFINTOSC FREQUENCY OVER VDD AND TEMPERATURE, PIC12LF1840 ONLY 36 34 Max. Frequency (kHz) 32 30 Typical 28 Min. 26 24 Max: Typical + 3ı (-40°C to +125°C) Typical: statistical mean @ 25°C Min: Typical - 3ı (-40°C to +125°C) 22 20 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 VDD (V) FIGURE 31-66: LFINTOSC FREQUENCY OVER VDD AND TEMPERATURE, PIC12F1840 ONLY 36 34 Max. Frequency (kHz) 32 30 Typical 28 26 Min.
PIC12(L)F1840 FIGURE 31-67: CAP SENSE CURRENT SINK/SOURCE CHARACTERISTICS, FIXED VOLTAGE REFERENCE (CPSRM = 0), HIGH CURRENT RANGE (CPSRNG = 11) 20 15 IPIN (uA) Sink Typical Sink Max. 10 Sink Min. 5 0 -5 Source Min. -10 Source Max. -15 Max: Typical + 3ı Typical: Min: Typical - 3ı Source Typical -20 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.
PIC12(L)F1840 FIGURE 31-69: CAP SENSE CURRENT SINK/SOURCE CHARACTERISTICS, FIXED VOLTAGE REFERENCE (CPSRM = 0), LOW CURRENT RANGE (CPSRNG = 01) 0.8 Sink Max. 0.6 Sink Typical 0.4 Sink Min. IPIN (uA) 0.2 0.0 -0.2 Source Min. -0.4 Source Typical -0.6 Source Max. -0.8 -1.0 Max: Typical + 3ı Typical: Min: Typical - 3ı -1.2 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (V) 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 NOTES: DS40001441D-page 382 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 32.
PIC12(L)F1840 32.2 MPLAB C Compilers for Various Device Families The MPLAB C Compiler code development systems are complete ANSI C compilers for Microchip’s PIC18, PIC24 and PIC32 families of microcontrollers and the dsPIC30 and dsPIC33 families of digital signal controllers. These compilers provide powerful integration capabilities, superior code optimization and ease of use. For easy source level debugging, the compilers provide symbol information that is optimized to the MPLAB IDE debugger. 32.
PIC12(L)F1840 32.7 MPLAB SIM Software Simulator The MPLAB SIM Software Simulator allows code development in a PC-hosted environment by simulating the PIC MCUs and dsPIC® DSCs on an instruction level. On any given instruction, the data areas can be examined or modified and stimuli can be applied from a comprehensive stimulus controller. Registers can be logged to files for further run-time analysis.
PIC12(L)F1840 32.11 PICkit 2 Development Programmer/Debugger and PICkit 2 Debug Express 32.13 Demonstration/Development Boards, Evaluation Kits, and Starter Kits The PICkit™ 2 Development Programmer/Debugger is a low-cost development tool with an easy to use interface for programming and debugging Microchip’s Flash families of microcontrollers.
PIC12(L)F1840 33.0 PACKAGING INFORMATION 33.1 Package Marking Information 8-Lead PDIP (300 mil) 12F1840 /P017 1212 XXXXXXXX XXXXXNNN YYWW 8-Lead SOIC (3.90 mm) Example 12F1840 /SN1212 017 NNN Legend: XX...X Y YY WW NNN e3 * Note: * Example Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code Pb-free JEDEC® designator for Matte Tin (Sn) This package is Pb-free.
PIC12(L)F1840 33.2 Package Marking Information 8-Lead DFN (3x3x0.9 mm) Example MFQ0 1212 017 XXXX YYWW NNN PIN 1 TABLE 33-1: PIN 1 8-LEAD 3X3 DFN (MF) TOP MARKING Part Number Marking PIC12F1840-E/MF MFQ0 PIC12F1840(T)-I/MF MFR0 PIC12LF1840-E/MF MFS0 PIC12LF1840(T)-I/MF MFT0 DS40001441D-page 388 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 33.3 Package Details The following sections give the technical details of the packages. 3 & ' !& " & 4 # * !( ! ! & 4 % & & # & && 255*** ' '5 4 N NOTE 1 E1 1 3 2 D E A2 A L A1 c e eB b1 b 6 &! ' ! 9 ' &! 7"') % ! 7,8.
PIC12(L)F1840 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS40001441D-page 390 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 ! "" #$ %& ! ' 3 & ' !& " & 4 # * !( ! ! & 4 % & & # & && 255*** ' '5 4 DS40001441D-page 392 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS40001441D-page 394 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 NOTES: DS40001441D-page 396 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 APPENDIX A: DATA SHEET REVISION HISTORY Revision A (02/2011) APPENDIX B: This section provides comparisons when migrating from other similar PIC® devices to the PIC12(L)F1840 family of devices. Original release of this data sheet. Revision B (05/2011) B.1 Updated ‘Special Microcontroller Features’ and ‘Low-Power Features’ sections; Updated Section 30.3, ‘DC Characteristics: PIC12(L)F1840-I/E (Power-down)’; Updated the Packaging Information section.
PIC12(L)F1840 NOTES: DS40001441D-page 398 Preliminary 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 THE MICROCHIP WEB SITE CUSTOMER SUPPORT Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers.
PIC12(L)F1840 NOTES: DS40001441D-page 400 2011-2013 Microchip Technology Inc.
PIC12(L)F1840 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. [X](1) PART NO.
PIC12(L)F1840 NOTES: DS40001441D-page 402 2011-2013 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature.
Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.
