Datasheet

PIC12(L)F1571/2
DS40001723D-page 266  2013-2015 Microchip Technology Inc.
TABLE 26-3: POWER-DOWN CURRENTS (IPD)
(1,2)
PIC12LF1571/2
Operating Conditions (unless otherwise stated)
Low-Power Sleep Mode
PIC12F1571/2 Low-Power Sleep Mode, VREGPM = 1
Param.
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
D022 Base IPD — 0.020 0.6 2.6 A 1.8 WDT, BOR and FVR disabled,
all peripherals inactive,
VREGPM = 1
— 0.025 0.8 2.9
A3.0
D022 Base IPD — 0.2 0.9 2.8 A 2.3 WDT, BOR and FVR disabled,
all peripherals inactive,
Low-Power Sleep mode,
VREGPM = 1
— 0.3 3.0 3.8 A 3.0
— 0.4 3.6 4.5 A 5.0
D022A Base IPD — 9 14 15 A 2.3 WDT, BOR and FVR disabled,
all peripherals inactive,
Normal Power Sleep mode,
VREGPM = 0
— 11 19 21 A 3.0
— 12 21 22 A 5.0
D023 — 0.3 0.8 2.9
A 1.8 WDT Current
— 0.5 1.1 3.5
A3.0
D023 — 0.5 1.7 4.1 A 2.3 WDT Current
— 0.6 1.9 4.4 A 3.0
— 0.7 2.1 4.7 A 5.0
D023A — 13 18 20
A 1.8 FVR Current
—2228 29
A3.0
D023A — 16 24 25 A 2.3 FVR Current
— 19 30 31 A 3.0
— 20 33 35 A 5.0
D024 — 6.5 9 11
A 3.0 BOR Current
D024 — 7.0 10 11 A 3.0 BOR Current
— 8.0 12 13 A 5.0
D24A — 0.2 2 4
A 3.0 LPBOR Current
D24A — 0.4 2 4 A 3.0 LPBOR Current
— 0.5 3 5 A 5.0
D026 — 0.03 0.7 2.7
A 1.8 ADC Current (Note 3),
No conversion in progress
— 0.04 0.8 3
A3.0
D026 — 0.2 1.3 3.8 A 2.3 ADC Current (Note 3),
No conversion in progress
— 0.3 1.4 3.9 A 3.0
— 0.4 1.5 4 A 5.0
D026A* — 250 — —
A 1.8 ADC Current (Note 3),
Conversion in progress
—250 — —
A3.0
D026A* — 280 — — A 2.3 ADC Current (Note 3),
Conversion in progress
— 280 — — A 3.0
— 280 — — A 5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, +25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral  current can be determined by subtracting the base IPD current from this limit. Max. values should be
used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
SS.
3: ADC clock source is FRC.