Datasheet

 2011 Microchip Technology Inc. Preliminary DS41615A-page 231
PIC12(L)F1501
27.3 DC Characteristics: PIC12(L)F1501-I/E (Power-Down)
PIC12LF1501
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C
 TA  +125°C for extended
PIC12F1501
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C
 TA  +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
Power-down Base Current (I
PD)
(2)
D022 — .02 1.0 2.4 A 1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— .03 1.1 3.0
A3.0
D022 — 10 35 40 A 2.3 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 11 42 48 A 3.0
— 12 45 61 A 5.0
D023 — 0.2 1.5 2.4
A 1.8 LPWDT Current (Note 1)
— 0.5 2.0 3.0 A3.0
D023 — 11 38 44 A 2.3 LPWDT Current (Note 1)
— 12 43 48 A 3.0
— 13 48 65 A 5.0
D023A — 13 22 25
A 1.8 FVR current (Note 1)
—22 24 27 A3.0
D023A — 23 62 65 A 2.3 FVR current (Note 1)
— 30 72 75 A 3.0
— 34 115 120 A 5.0
D024 — 7 14 16
A 3.0 BOR Current (Note 1)
D024 — 15 47 50 A 3.0 BOR Current (Note 1)
— 17 55 66 A 5.0
D024A — 0.2 5 7
A 3.0 LPBOR Current
D024A — 10 25 40 A 3.0 LPBOR Current
— 12 30 50 A 5.0
D026 — 0.03 3.5 4.0
A 1.8 A/D Current (Note 1, Note 3), no
conversion in progress
— 0.04 4.0 4.5
A3.0
D026 — 10 39 45 A 2.3 A/D Current (Note 1, Note 3), no
conversion in progress
— 11 43 49 A 3.0
— 12 46 65 A 5.0
D026A* — 250 1.5 3.0
A 1.8 A/D Current (Note 1, Note 3),
conversion in progress
— 250 2.0 3.5
A3.0
D026A* — 280 38 45 A 2.3 A/D Current (Note 1, Note 3),
conversion in progress
— 280 43 49 A 3.0
— 280 46 65 A 5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Legend: TBD = To Be Determined
Note 1: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral
 current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD.
3: A/D oscillator source is FRC.