Datasheet

ManualsBrandsMICROCHIP TECHNOLOGY ManualsPMICsPMIC - motor controllers Half-bridge (4) Ein/Aus SOP 24

 2010-2013 Microchip Technology Inc. DS22260C-page 1

Features

• 750 mA Continuous Output Current

• Load Voltage Supply: 10V to 40V

• Full Bipolar Stepper Motor Drive Capability

• Bidirectional DC Motor Capability

• Internal Fixed T

OFF

Time PWM Current Control

• Internal Protection Diodes

• Internal Thermal Shutdown

• Under Voltage Lockout

• LS-TTL Compatible Logic Inputs with Pull-Up

Resistors

•Low R

Output Resistance

• Low Quiescent Current

• Operating Temperature Range: -40°C to +105°C

• Pin Compatible with Allegro 6219

Applications

• Stepper Motor Actuators

• DC Motor Actuators

• Automotive HVAC Ventilation

• Automotive Power Seats

Description

The MTS62C19A motor driver is a CMOS device capa-

ble of driving both windings of a bipolar stepper motor

or bidirectionally control two DC motors. Each of the

two independent H-bridge outputs is capable of sus-

taining 40V and delivering up to 750 mA of continuous

current. The output current level is controlled by an

internal pulse-width modulation (PWM) circuit that is

configured using two logic inputs, a current sense

resistor, and a selectable reference voltage. The

H-bridge outputs have been optimized to provide a low

output saturation voltage drop.

Full, half and micro-stepping operations are possible

with the PWM current control and logic inputs. The

maximum output current is set by a sensing resistor

and a user-selectable reference voltage. The output

current limit is selected using two logic level inputs. The

selectable output current limits are 0%, 33%, 67% or

100% of the maximum output current. Each bridge has

a PHASE input signal which is used to control the

direction of current flow through the H-bridge and the

load.

The H-bridge power stage is controlled by non-overlap-

ping signals which prevent current cross conduction

when switching the direction of the current flow. Internal

clamp diodes protect against inductive transients.

Thermal protection circuitry disables the outputs when

the junction temperature exceeds the safe operating

limit. No special power-up sequencing is required.

Undervoltage Lockout circuitry prevents the chip from

operating when the load supply is applied prior to the

logic supply.

The device is supplied in a 24-pin SOP Package.

Package Types

Note: The MTS62C19A device is formerly a

product of Advanced Silicon.

GND

I01

LOAD

OUT1A

OUT2A

SENSE2

COMPIN2

OUT2B

GND

REF1

I11

PHASE1

GND

I02

SENSE1

I12

PHASE2

OUT1B

COMPIN1

MTS62C19A

SOP-24

REF2

RC2

RC1

LOGIC

Dual Full-Bridge Motor Driver

MTS62C19A

Summary of content (20 pages)

PAGE 1
MTS62C19A Dual Full-Bridge Motor Driver Features Description • • • • • • • • • The MTS62C19A motor driver is a CMOS device capable of driving both windings of a bipolar stepper motor or bidirectionally control two DC motors. Each of the two independent H-bridge outputs is capable of sustaining 40V and delivering up to 750 mA of continuous current.
PAGE 2
MTS62C19A Functional Block Diagram VLOGIC VLOAD PHASE1 I01 Drivers Shift Logic OUT1A Power Bridge I11 Current Sense Comparator VREF1 OUT1B One-shot Thermal Shutdown Under-V Lockout PHASE2 Shift Logic I02 Drivers Power Bridge I12 Current Sense Comparator VREF2 COMPIN1 DS22260C-page 2 COMPIN2 OUT2A OUT2B One-shot RC2 RC1 GND SENSE1 SENSE2  2010-2013 Microchip Technology Inc.
PAGE 3
MTS62C19A Typical Application 5V 10 to 30V 100 µF 100 nF VLOGIC 100 nF VLOAD PHASE1 I01 I11 Shift Logic Drivers Power Bridge OUT1A OUT1B Logic/µP VREF1 Current Sense Comparator One-shot Under-V Lockout PHASE2 I02 Shift Drivers OUT2A Logic I12 VREF2 Thermal Shutdown Power Bridge Current Sense Comparator M One-shot RC2 COMPIN1 COMPIN2 RC1 Ct Rt  2010-2013 Microchip Technology Inc.
PAGE 4
MTS62C19A 1.0 ELECTRICAL CHARACTERISTICS † Notice: Stresses above those listed under “Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Absolute Maximum Ratings † Logic Supply Voltage (VLOGIC) .........................
PAGE 5
MTS62C19A TEMPERATURE SPECIFICATIONS Parameters Sym Min Junction Temperature Range TJ Operating Temperature Range Typ Max Units Conditions -40 +125 °C TA -40 +105 °C Thermal Resistance, SOP-24 JA — 76 — °C/W EIA/JEDEC JESD51-10 Thermal Resistance, SOP-24 JC — 16 — °C/W EIA/JEDEC JESD51-10 Recommended Temperature Ranges Thermal Package Resistance  2010-2013 Microchip Technology Inc.
PAGE 6
MTS62C19A 2.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 2-1. TABLE 2-1: MTS62C19A PIN FUNCTION TABLE Pin No.
PAGE 7
MTS62C19A 2.1 Output Stage (OUT1A, OUT2A, OUT1B, OUT2B) Output connection to “A” side and “B” side of motor windings. 2.2 Current Sense Input (SENSE1, SENSE2) 2.6 Current Flow Direction Selection (PHASE1, PHASE2) Logic input to select the direction of the current flow through the load. A “HIGH” logic signal level causes load current to flow from OUTxA to OUTxB. A “LOW” logic level causes load current to flow from OUTxB to OUTxA.
PAGE 8
MTS62C19A 3.0 FUNCTIONAL DESCRIPTION 3.1 Each motor winding is driven by an H-type bridge consisting of two N and two P transistors that allow the current to flow in both winding directions depending on the value of the PHASE signal (Table 3-1). The H-bridge can be set in five configurations that are related to the digital inputs PHASE, I0 and I1 and to the current sensed. These configurations are shown in Table 3-2.
PAGE 9
MTS62C19A 3.2 PWM Current Control The current level in each motor winding is controlled by a PWM circuit with a fixed TOFF time. The load current flowing in the winding is sensed through an external sensing resistor RS, connected between the power bridge's source pin SENSE (sources of transistors Na and Nb) and GND. VLOAD Power Bridge VREF Pa Pb One-Shot OUTA ÷10 Source Disable OUTB I0 I1 FIGURE 3-2: Na COMPIN CC RC RC Ct SENSE RS Rt PWM Current Control Circuit Principle (Channel 1 Shown).
PAGE 10
MTS62C19A When the maximum allowed current is reached, the bridge source is turned off during a fixed period TOFF (typically 50 µs) given by a non-retriggerable pulse generator and the external timing components Rt (20k – 100 k range) and Ct (100 pF – 1000 pF range): EQUATION 3-2: 3.3 A thermal protection circuitry turns off all drivers when the junction temperature exceeds a safe operating limit of +170°C (typical). This protects the devices from failure due to excessive heating.
PAGE 11
MTS62C19A 4.0 APPLICATION CIRCUITS AND ISSUES 4.1 Typical Application The MTS62C19A circuit, with external components for a typical application, is shown in Figure 4-1. Typical passive component values are: RS = 1, RC = 1 k, CC = 820 pF, Rt = 56 k and Ct = 820 pF.
PAGE 12
MTS62C19A 4.2 Stepping Examples The MTS62C19A control modes are full-step, halfstep, modified half-step and microstepping control of the motor, as shown in Figure 4-2. Half-Step Full-Step 1 2 3 4 1 2 3 4 5 6 7 8 Modified Half-Step 1 2 3 4 5 6 7 8 Micro-Stepping (1/8th) 1... ...32 I01 I11 PHASE1 I02 I12 PHASE2 5V VREF1 VREF2 0V 5V 5V 5V 5V 0V +500 mA Motor Current in Phase 1 0 -500 mA +167 mA Motor Current in Phase 2 FIGURE 4-2: 4.
PAGE 13
MTS62C19A 5.0 PACKAGING INFORMATION 5.1 Package Marking Information 24-Lead SOP Example YYWWNNN Legend: XX...X Y YY WW NNN e3 * Note: MTS62C19A e3 HS105 ^^ 1248256 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free.
PAGE 14
MTS62C19A SOP 24L Package Outline Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 24 13 1 0.016 typ 12 0.05 typ D L GAUGE PLANE SEATING PLANE Note: The package drawing dimensions are expressed in inches. Symbol Minimum Typical A — — Note 1: 2: 3: A1 0.102 (0.004) D 15.545 (0.612) Maximum 2.642 (0.104) — 15.697 (0.618) — Unit mm (inch) mm (inch) 15.850 (0.624) mm (inch) E 7.417 (0.
PAGE 15
MTS62C19A APPENDIX A: REVISION HISTORY Revision C (March 2013) The following is the list of modifications: 1. 2. Corrected one dimension in the package drawing. Added a note mentioning the unit type used in the drawing. Minor editorial changes. Revision B (December 2012) The following is the list of modifications: 1. 2. 3. 4. Updated Operating Temperature Range throughout the document. Corrected Typical Application diagram. Added Section 5.1, Package Marking Information.
PAGE 16
MTS62C19A NOTES: DS22260C-page 16  2010-2013 Microchip Technology Inc.
PAGE 17
MTS62C19A PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO.
PAGE 18
MTS62C19A NOTES: DS22260C-page 18  2010-2013 Microchip Technology Inc.
PAGE 19
Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature.
PAGE 20
Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.