Information

dsPICDEM™ MCLV-2 Development Board
(DM330021-2)
The dsPICDEM MCLV-2 Development
Board provides a cost-effective method
for evaluating and developing sensored
or sensorless Brushless DC (BLDC)
and Permanent Magnet Synchronous
motor control applications. The board supports our 28-pin
SOIC versions of our dsPIC33F/E digital signal controllers
as well as a variety of Plug-In Modules (PIMs). Either the
internal, on chip op amps or the external op amps on the
MCLV-2 board can be used, and we provide PIMs for both
options. The MCLV-2 is fully backwards-compatible with
the original MCLV and all PIMs. The board is capable of
controlling motors rated up to 48V and 15 Amps. It is
designed to work with the 24V BLDC Motor (AC300020)
and the 24V Motor Power Supply (AC002013) to create
a complete 24V BLDC development kit. It also supports
multiple communications channels such as USB, CAN, LIN
and RS-232.
dsPICDEM MCHV-2 Development System
(DM330023-2)
The dsPICDEM MCHV-2 Development
System enables rapid development
of a wide variety of high-voltage
motor control applications using a
dsPIC DSC, including Brushless DC
(BLDC) motors, Permanent Magnet
Synchronous Motors (PMSM), and AC Induction Motors
(ACIM), in sensor or sensorless operation. The MCHV-2
outputs up to 1000W at 400V from 85–285 VAC input and
has an integrated power factor correction stage. The MCHV-
2 supports the dsPIC33F/E Motor Control device families
and offers a mounting option to connect either a 28-pin
SOIC device or a generic 100-pin Plug-in Module PIM. The
MCHV-2 allows either the internal, on-chip op amps found
on certain dsPIC DSC devices or the external op amps on
the MCHV-2 board to be used. We provide PIMs for using
either the internal or external op amps.
Low-Voltage Motor Control Development Bundle
(DV330100)
This Low-Voltage Motor Control
Development Bundle provides a cost-
effective method of evaluating and
developing a dual/single motor control
power stage targeted to drive two
Brushless DC (BLDC) motors or Permanent
Magnet Synchronous Motors (PMSM)
concurrently. The bundle comes with a dsPIC DSC
Signal Board, a Motor Control 10–24V Driver Board and
a dsPIC33EP512GM710 Dual-Motor Control PIM. This
bundle provides a platform for building and evaluating
embedded motor control application software with the
dsPIC33EP family.
motor control applications. The board supports our 28-pin
Buck/Boost Converter PICtail Plus Card
(AC164133)
A low-cost development platform for dsPIC33F GS SMPS
devices, the Buck/Boost Converter PICtail Plus Card has
two buck stage outputs and one boost stage output. This
board can be used with the Explorer 16 board or with the
16-bit 28-pin starter board and the dsPIC33F GS SMPS
and digital power conversion devices.
Security
Wireless Security Remote Control Development Kit
(DM182017-1/2/3/4)
The Wireless Security Remote
Control Development Kit is a
demonstration and development
platform for wireless security
remote control applications.
DM182017-1/2/3 demonstrates
two security protocols; KeeLoq®
Classic protocol and KeeLoq Advanced (AES-128) protocol.
DM182017-4 demonstrates Ultimate KeeLoq and KeeLoq
Classic protocols. Each kit contains a four-button key
fob transmitter based on the PIC12LF1840T39A, which
is programmed to the MHz corresponding to the specific
kit as shown below. The kits also contain a receiver
PICtail daughterboard and the Embedded Security
Development Board.
■ DM182017-1 433.92 MHz
■ DM182017-2 868 MHz
■ DM182017-3 915 MHz
■ DM182017-4 433.92 MHz
Application-Specific Development Tools
13
Quick Guide to Microchip Development Tools