Information

58
Analog and Interface Product Selector Guide
Featured Analog Development Tools
Thermal Management Products
MCP9600 Evaluation Board (ADM00665)
The MCP9600 Evaluation Board is
used to digitize the Thermocouple
EMF voltage to degree Celsius with
±1.5°C accuracy. You can easily
evaluate all device features using
a Type K thermocouple. The device also supports Types
J, T, N, E, B, S and R. Each of these types are evaluated
by replacing the Type K Thermocouple connector with the
corresponding connectors (not included).
Thermocouple Reference Design (TMPSNSRD-TCPL1)
This reference design demonstrates
how to instrument a thermocouple and
accurately sense temperature over
the entire thermocouple measurement range. This solution
uses the MCP3421 18-bit Analog-to-Digital Converter (ADC)
to measure voltage across the thermocouple.
Power Management Products
MCP19111 Evaluation Board (ADM00397)
The MCP19111 is a digitally-enhanced PWM
controller. It combines a pure-analog PWM
controller with a supervisory microcontroller
making it a fast, cost-effective and configurable
power conversion solution. The MCP19111 is
ideal for standard power conversion, LED drivers and battery
charging applications. This board demonstrates how the
MCP19111 device operates in a synchronous buck topology
over a wide input voltage and load range.
MCP16251 and MCP1640B Synchronous Boost
Converters Evaluation Board (ADM00458)
This board demonstrates the MCP16251/
MCP1640B in two boost-converter
applications with multiple output voltages and
was developed to help reduce product design
cycle time. Three common output voltages
can be selected: 2.0V, 3.3V and 5.0V.
MCP8025 TQFP BLDC Motor Driver Evaluation
Board (ADM00600)
This board demonstrates our MCP8025
3-phase BLDC motor gate driver with
power module used in a BLDC motor drive
application. When used in conjunction with
a microcontroller, the MCP8025 will provide
the necessary drive signals for a 3-phase BLDC motor.
The MCP8025 contains the high-side and low-side drivers
for external N-channel MOSFETs. A dsPIC33EP256MC504
processor is used to supply the PWM inputs to the
MCP8025 as well as handle the high-speed analog-to-
digital conversion required for 50 kHz PWM operation.
The MCP8025 UART interface is used to configure the
MCP8025 device and to send fault information to the
dsPIC® DSC.
Board (ADM00600)
Linear Products
MCP6V01 Thermocouple Auto-Zeroed
Reference Design Board (MCP6V01RD-TCPL)
The MCP6V01 design board
demonstrates how to use a difference
amplifier system to measure
Electromotive Force (EMF) voltage at
the cold junction of thermocouple to accurately measure
temperature of the thermocouple bead. This can be done
by using the MCP6V01 auto-zeroed op amp because of
its ultra-low offset voltage (VOS) and high Common Mode
Rejection Ratio (CMRR).
MCP6N11 and MCP6V2X Wheatstone Bridge
Reference Design (ARD00354)
This board demonstrates the performance
of the MCP6N11 instrumentation amplifier
(INA) and a traditional three op amp INA using
the MCP6V26 and MCP6V27 auto-zeroed
op amps. The input signal comes from an
RTD temperature sensor in a Wheatstone bridge. Real-world
interference is added to the bridge’s output to provide realistic
performance comparisons. Data is gathered and displayed on
a PC for ease of use.
MCP6421 EMIRR Evaluation Board (ADM00443)
The MCP6421 EMIRR Evaluation
Board is intended to support
the Electromagnetic Interference
Rejection Ratio (EMIRR) measurement and to show the
Electromagnetic Interference (EMI) rejection capability of
the MCP6421 operational amplifier.
Mixed Signal Products
MCP37X3X-200 16-bit 200 Msps ADC VTLA
Evaluation Board (ADM00505)
This board provides the opportunity
to evaluate the performance of the
MCP37X3X-200 device family. With the
on-board MCP37D31-200 16-bit 200 Msps
pipelined ADC, it allows you to evaluate the
functionality of the 16-bit 200 Msps ADCs and the digital
signal processing features. With the help of a compatible
data capture card, the evaluation board can provide you with
performance analysis features through the PC GUI.
PAC1921 High-Side Power and Current Monitor
Evaluation Board (ADM00592)
The PAC1921 is a dedicated power
monitoring device with a configurable analog
output. This device is unique in that all
power-related information is available on the
2-wire/I
2
C-compatible interface and power,
current or voltage is available on the analog
output. This evaluation board provides you with the means
to exercise device functionality while connected either to
target systems or while utilizing on-board sources.
Reference Design Board (MCP6V01RD-TCPL)
Reference Design (ARD00354)
MCP6421 EMIRR Evaluation Board (ADM00443)
For a complete list of development tools, please visit www.microchip.com/development tools.