Datasheet

MCP660/1/2/3/4/5/9
DS22194D-page 4  2009-2012 Microchip Technology Inc.
Output
Maximum Output Voltage Swing V
OL
, V
OH
V
SS
+ 25 — V
DD
 25 mV V
DD
= 2.5V, G = +2,
0.5V Input Overdrive
V
OL
, V
OH
V
SS
+ 50 — V
DD
 50 mV V
DD
= 5.5V, G = +2,
0.5V Input Overdrive
Output Short Circuit Current I
SC
±45 ±90 ±145 mA V
DD
= 2.5V (Note 2)
I
SC
±40 ±80 ±150 mA V
DD
= 5.5V (Note 2)
Power Supply
Supply Voltage V
DD
2.5 — 5.5 V
Quiescent Current per Amplifier I
Q
3 6 9 mA No Load Current
TABLE 1-2: AC ELECTRICAL SPECIFICATIONS
Electrical Characteristics: Unless indicated, T
A
= +25°C, V
DD
= +2.5V to +5.5V, V
SS
= GND, V
CM
= V
DD
/2,
V
OUT
 V
DD
/2, V
L
= V
DD
/2, R
L
= 1 k to V
L
, C
L
= 20 pF and CS = V
SS
(refer to Figure 1-2).
Parameters Sym Min Typ Max Units Conditions
AC Response
Gain Bandwidth Product GBWP — 60 — MHz
Phase Margin PM — 65 — ° G = +1
Open Loop Output Impedance R
OUT
—10— 
AC Distortion
Total Harmonic Distortion plus Noise THD+N — 0.003 — % G = +1, V
OUT
= 2V
P-P
, f = 1 kHz,
V
DD
= 5.5V, BW = 80 kHz
Differential Gain, Positive Video
(Note 1)
DG — 0.3 — % NTSC, V
DD
= +2.5V, V
SS
= -2.5V,
G = +2, V
L
= 0V, DC V
IN
= 0V to
0.7V
Differential Gain, Negative Video
(Note 1)
DG — 0.3 — % NTSC, V
DD
= +2.5V, V
SS
= -2.5V,
G = +2, V
L
= 0V,
DC V
IN
= 0V to -0.7V
Differential Phase, Positive Video
(Note 1)
DP — 0.3 — ° NTSC, V
DD
= +2.5V, V
SS
= -2.5V,
G = +2, V
L
= 0V,
DC V
IN
= 0V to 0.7V
Differential Phase, Negative Video
(Note 1)
DP — 0.9 — ° NTSC, V
DD
= +2.5V, V
SS
= -2.5V,
G = +2, V
L
= 0V,
DC V
IN
= 0V to -0.7V
Step Response
Rise Time, 10% to 90% t
r
— 5 — ns G = +1, V
OUT
= 100 mV
P-P
Slew Rate SR — 32 — V/µs G = +1
Noise
Input Noise Voltage E
ni
—14—µV
P-P
f = 0.1 Hz to 10 Hz
Input Noise Voltage Density e
ni
—6.8—nV/Hz f = 1 MHz
Input Noise Current Density i
ni
4—fA/Hz f = 1 kHz
Note 1: These specifications are described in detail in Section 4.3 “Distortion”. (NTSC refers to a National
Television Standards Committee signal.)
TABLE 1-1: DC ELECTRICAL SPECIFICATIONS (CONTINUED)
Electrical Characteristics: Unless otherwise indicated, T
A
= +25°C, V
DD
= +2.5V to +5.5V, V
SS
= GND,
V
CM
= V
DD
/3, V
OUT
 V
DD
/2, V
L
= V
DD
/2, R
L
= 1 k to V
L
and CS = V
SS
(refer to Figure 1-2).
Parameters Sym Min Typ Max Units Conditions
Note 1: See Figure 2-5 for temperature effects.
2: The I
SC
specifications are for design guidance only; they are not tested.