Datasheet

ManualsBrandsMICROCHIP TECHNOLOGY ManualsLinear ICsLinear IC - Comparator Multi-purpose CMOS, Open drain SOT 23 5

 2009-2013 Microchip Technology Inc. DS22143D-page 1

MCP6566/6R/6U/7/9

Features:

• Propagation Delay at 1.8V

- 56 ns (typical) High-to-Low

• Low Quiescent Current: 100 µA (typical)

• Input Offset Voltage: ±3 mV (typical)

• Rail-to-Rail Input: V

- 0.3V to V

+ 0.3V

• Open-Drain Output

• Wide Supply Voltage Range: 1.8V to 5.5V

• Available in Single, Dual and Quad

• Packages: SC70, SOT-23-5, SOIC, MSOP,

TSSOP

Typical Applications:

• Laptop Computers

• Mobile Phones

• Hand-held Electronics

• RC Timers

• Alarm and Monitoring Circuits

• Window Comparators

• Multivibrators

Design Aids:

• Microchip Advanced Part Selector (MAPS)

• Analog Demonstration and Evaluation Boards

• Application Notes

Related Device:

• Push-Pull Output: MCP6561/1R/1U/2/4

Typical Application

Description:

The Microchip Technology, Inc. MCP6566/6R/6U/7/9

families of open-drain output comparators are offered

in single, dual and quad configurations.

These comparators are optimized for low-power 1.8V,

single-supply applications with greater than rail-to-rail

input operation. The internal input hysteresis eliminates

output switching due to internal input noise voltage,

reducing current draw. The open-drain output of the

MCP6566/6R/6U/7/9 family requires a pull-up resistor

and it supports pull-up voltages above and below V

DD,

which can be used to level shift. The output toggle

frequency can reach a typical of 4 MHz (typical) while

limiting supply current surges and dynamic power

consumption during switching.

This family operates with single supply voltage of 1.8V

to 5.5V while drawing less than 100 µA/comparator of

quiescent current (typical).

Package Types

OUT

+5V

+3V

MCP656X

MCP6567

+INA

-INA

OUTA

OUTB

-INB

+INB

MCP6569

+INA

-INA

OUTA

OUTD

-IND

+IND

OUTB

-INB

+INB

+INC

-INC

OUTC

MCP6566

MCP6566R

+IN

OUT

-IN

+IN

OUT

-IN

SOT-23-5, SC70-5 SOIC, MSOP

SOT-23-5

SOIC, TSSOP

SOT-23-5

–

OUT

MCP6566U

1.8V Low-Power Open-Drain Output Comparator

Summary of content (48 pages)

PAGE 1
MCP6566/6R/6U/7/9 1.8V Low-Power Open-Drain Output Comparator Features: Description: • Propagation Delay at 1.8VDD: - 56 ns (typical) High-to-Low • Low Quiescent Current: 100 µA (typical) • Input Offset Voltage: ±3 mV (typical) • Rail-to-Rail Input: VSS - 0.3V to VDD + 0.3V • Open-Drain Output • Wide Supply Voltage Range: 1.8V to 5.5V • Available in Single, Dual and Quad • Packages: SC70, SOT-23-5, SOIC, MSOP, TSSOP The Microchip Technology, Inc.
PAGE 2
MCP6566/6R/6U/7/9 NOTES: DS22143D-page 2  2009-2013 Microchip Technology Inc.
PAGE 3
MCP6566/6R/6U/7/9 1.0 ELECTRICAL CHARACTERISTICS 1.1 Maximum Ratings † † Notice: Stresses above those listed under “Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. VDD - VSS ...........................................
PAGE 4
MCP6566/6R/6U/7/9 DC CHARACTERISTICS (CONTINUED) Electrical Characteristics: Unless otherwise indicated: VDD = +1.8V to +5.5V, VSS = GND, TA = +25°C, VIN+ = VDD/2, VIN- = VSS, and RPull-Up = 20 k to VPU = VDD (see Figure 1-1). Parameters Symbol Min Typ Max Units VPULL_UP 1.6 VOH — IOH_leak Conditions — 5.5 V — VPULL_UP V (see Figure 1-1) (Notes 3, 4) — — 1 µA Note 4 VOL — — 0.6 V IOUT = 3 mA/8 mA @ VDD = 1.8V/5.
PAGE 5
MCP6566/6R/6U/7/9 1.2 Test Circuit Configuration This test circuit configuration is used to determine the AC and DC specifications. VDD MCP656X VPU = VDD 200 k IOUT VOUT 25 pF 200 k VIN = VSS RPU 20 k VSS = 0V FIGURE 1-1: AC and DC Test Circuit for the Open-Drain Output Comparators.  2009-2013 Microchip Technology Inc.
PAGE 6
MCP6566/6R/6U/7/9 NOTES: DS22143D-page 6  2009-2013 Microchip Technology Inc.
PAGE 7
MCP6566/6R/6U/7/9 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
PAGE 8
MCP6566/6R/6U/7/9 Note: Unless otherwise indicated, VDD = +1.8V to +5.5V, VSS = GND, TA = +25°C, VIN+ = VDD /2, VIN – = GND, RL = 20 k to VPU = VDD , and CL = 25 pF. 3.0 5.0 VCM = VSS 2.0 VCM = VSS VDD = 1.8V VHYST (mV) V OS (mV) 4.0 1.0 0.0 -1.0 3.0 VDD= 1.8V 2.0 VDD = 5.5V -2.0 VDD= 5.0V -3.0 1.0 -50 -25 0 FIGURE 2-7: Temperature. 4.0 25 50 75 Temperature (°C) 100 125 Input Offset Voltage vs. -50 -25 0 FIGURE 2-10: Temperature. 25 50 75 Temperature (°C) 5.0 VDD = 1.8V 2.
PAGE 9
MCP6566/6R/6U/7/9 Note: Unless otherwise indicated, VDD = +1.8V to +5.5V, VSS = GND, TA = +25°C, VIN+ = VDD /2, VIN – = GND, RL = 20 k to VPU = VDD , and CL = 25 pF. 3.0 5.0 0.0 TA= +125°C TA= +85°C 4.0 TA= -40°C TA= +25°C TA= +85°C TA= +125°C 1.0 V HYST (mV) VOS (mV) 2.0 -1.0 TA= +25°C 3.0 TA= -40°C 2.0 -2.0 -3.0 1.0 1.5 2.5 3.5 VDD (V) 4.5 5.5 1.5 FIGURE 2-13: Input Offset Voltage vs. Supply Voltage vs. Temperature. 4.5 5.5 140.0 VDD = 5.5V Avg.
PAGE 10
MCP6566/6R/6U/7/9 Note: Unless otherwise indicated, VDD = +1.8V to +5.5V, VSS = GND, TA = +25°C, VIN+ = VDD /2, VIN – = GND, RL = 20 k to VPU = VDD , and CL = 25 pF. 150 150 IDD Spike near VPU = 0.9V VDD = 5.5 V VDD = 5.5V VDD = 4.5V VDD = 3.5V 100 VDD = 2.5V VDD = 2.0V VDD = 1.8V 75 -2.5 -0.5 100,000 0dB Output Attenuation 1.5 3.5 VPU - V DD (V) 5.5 7.5 9.5 TA = 10,000 VDD = 5.5V 250 200 VDD = 1.8V 150 VDD = 2.0 V FIGURE 2-22: Quiescent Current vs. Pull-up to Supply Voltage Difference.
PAGE 11
MCP6566/6R/6U/7/9 Note: Unless otherwise indicated, VDD = +1.8V to +5.5V, VSS = GND, TA = +25°C, VIN+ = VDD /2, VIN – = GND, RL = 20 k to VPU = VDD , and CL = 25 pF. 50% VDD = 1.8V 100 mV Over-Drive VCM = VDD /2 40% Occurrences (%) Occurrences (%) 50% tPHL Avg. = 54.4 ns StDev= 2 ns 198 units 30% 20% 10% 0% 40% 30% 20% 10% 0% 30 35 40 45 50 55 60 65 70 75 80 30 35 40 45 Prop. Delay (ns) FIGURE 2-25: Delays. High-to-Low Propagation FIGURE 2-28: Delays.
PAGE 12
MCP6566/6R/6U/7/9 Note: Unless otherwise indicated, VDD = +1.8V to +5.5V, VSS = GND, TA = +25°C, VIN+ = VDD /2, VIN – = GND, RL = 20 k to VPU = VDD , and CL = 25 pF. 80 80 VDD= 1.8V 100 mV Over-Drive 70 Prop. Delay (ns) Prop. Delay (ns) 70 tPHL 60 50 40 20 0.00 tPHL 50 40 20 0.50 1.00 VCM (V) 1.50 2.00 FIGURE 2-31: Propagation Delay vs. Common-mode Input Voltage. 0.0 10000 100mV Over-Drive VCM = VDD /2 VDD = 1.8V, tPHL Prop. Delay (ns) 100 10 VDD = 5.5V, tPHL 1 0.1 0.01 0.001 1 0.
PAGE 13
MCP6566/6R/6U/7/9 Note: Unless otherwise indicated, VDD = +1.8V to +5.5V, VSS = GND, TA = +25°C, VIN+ = VDD /2, VIN – = GND, RL = 20 k to VPU = VDD , and CL = 25 pF. 80 30% 78 VCM = VSS VDD = 1.8V to 5.5V 76 Occurrences (%) CMRR/PSRR (dB) Input Referred PSRR 74 CMRR 72 VCM = -0.3V to VDD + 0.3V VDD = 5.5V 20% 10% 70 0 25 50 75 Temperature (°C) 100 125 30% VDD = 1.8V 3588 units 20% -4 -3 -2 -1 0 1 2 3 4 5 CMRR (mV/V) VCM = VSS Avg.
PAGE 14
MCP6566/6R/6U/7/9 Note: Unless otherwise indicated, VDD = +1.8V to +5.5V, VSS = GND, TA = +25°C, VIN+ = VDD /2, VIN – = GND, RL = 20 k to VPU = VDD , and CL = 25 pF. Output Jitter pk-pk (ns) 10000 VDD = 5.5V 1000 VIN+ = 2Vpp (sine) 100 10 1 0.1 100 100 1k 1000 FIGURE 2-43: Frequency. DS22143D-page 14 10k 100k 1M 10000 100000 100000 Input Frequency (Hz) 0 10M 1E+07 Output Jitter vs. Input  2009-2013 Microchip Technology Inc.
PAGE 15
MCP6566/6R/6U/7/9 3.0 PIN DESCRIPTIONS Descriptions of the pins are listed in Table 3-1. TABLE 3-1: PIN FUNCTION TABLE MCP6566 MCP6566R MCP6566U MCP6567 MCP6569 SC70-5, SOT-23-5 SOT-23-5 SOT-23-5 MSOP, SOIC SOIC, TSSOP 1 1 5 1 1 3.
PAGE 16
MCP6566/6R/6U/7/9 NOTES: DS22143D-page 16  2009-2013 Microchip Technology Inc.
PAGE 17
MCP6566/6R/6U/7/9 4.0 APPLICATIONS INFORMATION The MCP6566/6R/6U/7/9 family of open-drain output comparators are fabricated on Microchip’s state-of-the-art CMOS process. They are suitable for a wide range of high speed applications requiring lowpower consumption. 4.1 Comparator Inputs 4.1.1 NORMAL OPERATION The input stage of this family of devices uses two differential input stages in parallel.
PAGE 18
MCP6566/6R/6U/7/9 It is also possible to connect the diodes to the left of the resistors R1 and R2. In this case, the currents through the diodes D1 and D2 need to be limited by some other mechanism. The resistor then serves as in-rush current limiter; the DC current into the input pins (VIN+ and VIN–) should be very small. 4.3.1 NON-INVERTING CIRCUIT Figure 4-4 shows a non-inverting circuit for single-supply applications using just two resistors. The resulting hysteresis diagram is shown in Figure 4-5.
PAGE 19
MCP6566/6R/6U/7/9 4.3.2 INVERTING CIRCUIT Where: R2 R3 R 23 = ------------------R2 + R3 Figure 4-6 shows an inverting circuit for single-supply using three resistors. The resulting hysteresis diagram is shown in Figure 4-7.
PAGE 20
MCP6566/6R/6U/7/9 4.6 PCB Surface Leakage 4.7 In applications where low input bias current is critical, PCB (Printed Circuit Board) surface leakage effects need to be considered. Surface leakage is caused by humidity, dust or other contamination on the board. Under low humidity conditions, a typical resistance between nearby traces is 1012. A 5V difference would cause 5 pA of current to flow. This is greater than the MCP6566/6R/6U/7/9 family’s bias current at +25°C (1 pA, typical).
PAGE 21
MCP6566/6R/6U/7/9 4.9 Typical Applications 4.9.1 4.9.3 PRECISE COMPARATOR Some applications require higher DC precision. An easy way to solve this problem is to use an amplifier (such as the MCP6291) to gain-up the input signal before it reaches the comparator. Figure 4-12 shows an example of this approach. BISTABLE MULTIVIBRATOR A simple bistable multivibrator design is shown in Figure 4-14. VREF needs to be between the power supplies (VSS = GND and VDD) to achieve oscillation.
PAGE 22
MCP6566/6R/6U/7/9 NOTES: DS22143D-page 22  2009-2013 Microchip Technology Inc.
PAGE 23
MCP6566/6R/6U/7/9 5.0 DESIGN AIDS 5.3 5.1 Microchip Advanced Part Selector (MAPS) The following Microchip Application Note is available on the Microchip web site at www.microchip.com and is recommended as a supplemental reference resource: MAPS is a software tool that helps semiconductor professionals efficiently identify Microchip devices that fit a particular design requirement. Available at no cost from the Microchip web site at www.microchip.
PAGE 24
MCP6566/6R/6U/7/9 NOTES: DS22143D-page 24  2009-2013 Microchip Technology Inc.
PAGE 25
MCP6566/6R/6U/7/9 6.0 PACKAGING INFORMATION 6.1 Package Marking Information 5-Lead SC70 (MCP6566) Example: BJ25 XXNN 5-Lead SOT-23 (MCP6566, MCP6566R) Device XXNN Example: Code MCP6566T JYNN MCP6566RT JZNN MCP6566UT WLNN JY25 Note: Applies to 5-Lead SOT-23. 8-Lead MSOP (MCP6567) Example: XXXXXX 6567E YWWNNN 302256 8-Lead SOIC (150 mil) (MCP6567) MCP6567E e3 SN^^1302 256 XXXXXXXX XXXXYYWW NNN Legend: XX...
PAGE 26
MCP6566/6R/6U/7/9 Package Marking Information (Continued) 14-Lead SOIC (150 mil) (MCP6569) Example: MCP6569 E/SL^^ e3 1302256 XXXXXXXXXX XXXXXXXXXX YYWWNNN 14-Lead TSSOP (MCP6569) XXXXXXXX YYWW NNN DS22143D-page 26 Example: MCP6569E 1302 256  2009-2013 Microchip Technology Inc.
PAGE 27
MCP6566/6R/6U/7/9 .
PAGE 28
MCP6566/6R/6U/7/9 . # # $ # / ! - 0 # 1 / % # # ! # ## +22--- 2 / DS22143D-page 28  2009-2013 Microchip Technology Inc.
PAGE 29
MCP6566/6R/6U/7/9 ! .
PAGE 30
MCP6566/6R/6U/7/9 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS22143D-page 30  2009-2013 Microchip Technology Inc.
PAGE 31
MCP6566/6R/6U/7/9 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2009-2013 Microchip Technology Inc.
PAGE 32
MCP6566/6R/6U/7/9 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS22143D-page 32  2009-2013 Microchip Technology Inc.
PAGE 33
MCP6566/6R/6U/7/9 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2009-2013 Microchip Technology Inc.
PAGE 34
MCP6566/6R/6U/7/9 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS22143D-page 34  2009-2013 Microchip Technology Inc.
PAGE 35
MCP6566/6R/6U/7/9 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2009-2013 Microchip Technology Inc.
PAGE 36
MCP6566/6R/6U/7/9 " # $% !&' ( ) * . # # $ # / ! - 0 # 1 / % # # ! # ## +22--- 2 / DS22143D-page 36  2009-2013 Microchip Technology Inc.
PAGE 37
MCP6566/6R/6U/7/9 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2009-2013 Microchip Technology Inc.
PAGE 38
MCP6566/6R/6U/7/9 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS22143D-page 38  2009-2013 Microchip Technology Inc.
PAGE 39
MCP6566/6R/6U/7/9 . # # $ # / ! - 0 # 1 / % # # ! # ## +22--- 2 /  2009-2013 Microchip Technology Inc.
PAGE 40
MCP6566/6R/6U/7/9 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS22143D-page 40  2009-2013 Microchip Technology Inc.
PAGE 41
MCP6566/6R/6U/7/9 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2009-2013 Microchip Technology Inc.
PAGE 42
MCP6566/6R/6U/7/9 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS22143D-page 42  2009-2013 Microchip Technology Inc.
PAGE 43
MCP6566/6R/6U/7/9 APPENDIX A: REVISION HISTORY Revision D (February 2013) The following is the list of modifications: 1. Added the Analog Input (VIN) parameter in Section 1.0 “Electrical Characteristics”. Revision C (February 2011) The following is the list of modifications: 1. Replaced the MCP5468 package name with the correct MCP6567 package name on page 1 and in Table 3-1. Revision B (August 2009) The following is the list of modifications: 1. 2. Added MCP6566U throughout the document.
PAGE 44
MCP6566/6R/6U/7/9 NOTES: DS22143D-page 44  2009-2013 Microchip Technology Inc.
PAGE 45
MCP6566/6R/6U/7/9 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO.
PAGE 46
MCP6566/6R/6U/7/9 NOTES: DS22143D-page 46  2009-2013 Microchip Technology Inc.
PAGE 47
Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature.
PAGE 48
Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.