Datasheet

MCP453X/455X/463X/465X
DS22096B-page 10  2008-2013 Microchip Technology Inc.
Rheostat
Differential Non-linearity
MCP45X1
(Note 4, Note 8)
MCP4XX2 devices only
(Note 4)
R-DNL -0.5 ±0.25 +0.5 LSb 5 k 8-bit 5.5V, I
W
= 900 µA
-1.0 +0.5 +1.0 LSb 3.0V, I
W
= 480 µA
(Note 7)
-0.375 ±0.25 +0.375 LSb 7-bit 5.5V, I
W
= 900 µA
-0.75 +0.5 +0.75 LSb 3.0V, I
W
= 480 µA
(Note 7)
-0.5 ±0.25 +0.5 LSb 10 k 8-bit 5.5V, I
W
= 450 µA
-1.0 +0.25 +1.0 LSb 3.0V, I
W
= 240 µA
(Note 7)
-0.375 ±0.25 +0.375 LSb 7-bit 5.5V, I
W
= 450 µA
-0.75 +0.5 +0.75 LSb 3.0V, I
W
= 240 µA
(Note 7)
-0.5 ±0.25 +0.5 LSb 50 k 8-bit 5.5V, I
W
= 90 µA
-0.5 ±0.25 +0.5 LSb 3.0V, I
W
= 48 µA
(Note 7)
-0.375 ±0.25 +0.375 LSb 7-bit 5.5V, I
W
= 90 µA
-0.375 ±0.25 +0.375 LSb 3.0V, I
W
= 48 µA
(Note 7)
-0.5 ±0.25 +0.5 LSb 100 k 8-bit 5.5V, I
W
= 45 µA
-0.5 ±0.25 +0.5 LSb 3.0V, I
W
= 24 µA
(Note 7)
-0.375 ±0.25 +0.375 LSb 7-bit 5.5V, I
W
= 45 µA
-0.375 ±0.25 +0.375 LSb 3.0V, I
W
= 24 µA
(Note 7)
Capacitance (P
A
)C
AW
— 75 — pF f =1 MHz, Code = Full-Scale
Capacitance (P
w
)C
W
— 120 — pF f =1 MHz, Code = Full-Scale
Capacitance (P
B
)C
BW
— 75 — pF f =1 MHz, Code = Full-Scale
AC/DC CHARACTERISTICS (CONTINUED)
DC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature –40°C  T
A
 +125°C (extended)
All parameters apply across the specified operating ranges unless noted.
V
DD
= +2.7V to 5.5V, 5 k, 10 k, 50 k, 100 k devices.
Typical specifications represent values for V
DD
= 5.5V, T
A
= +25°C.
Parameters Sym Min Typ Max Units Conditions
Note 1: Resistance is defined as the resistance between terminal A to terminal B.
2: INL and DNL are measured at V
W
with V
A
= V
DD
and V
B
= V
SS
.
3: MCP4XX1 only.
4: MCP4XX2 only, includes V
WZSE
and V
WFSE
.
5: Resistor terminals A, W and B’s polarity with respect to each other is not restricted.
6: This specification by design.
7: Non-linearity is affected by wiper resistance (R
W
), which changes significantly overvoltage and
temperature.
8: The MCP4XX1 is externally connected to match the configurations of the MCP45X2 and MCP46X2, and
then tested.
9: POR/BOR is not rate dependent.
10: Supply current is independent of current through the resistor network.
11: When HVC/A0 = V
IHH
, the I
DD
current is less due to current into the HVC/A0 pin. See I
PU
specification.