Datasheet

MCP414X/416X/424X/426X
DS22059B-page 6 © 2008 Microchip Technology Inc.
Full-Scale Error
(MCP4XX1 only)
(8-bit code =
100h,
7-bit code = 80h)
V
WFSE
-6.0 -0.1 — LSb 5 kΩ 8-bit 3.0V ≤ V
DD
≤ 5.5V
-4.0 -0.1 — LSb 7-bit 3.0V ≤ V
DD
≤ 5.5V
-3.5 -0.1 — LSb 10 kΩ 8-bit 3.0V ≤ V
DD
≤ 5.5V
-2.0 -0.1 — LSb 7-bit 3.0V ≤ V
DD
≤ 5.5V
-0.8 -0.1 — LSb 50 kΩ 8-bit 3.0V ≤ V
DD
≤ 5.5V
-0.5 -0.1 — LSb 7-bit 3.0V ≤ V
DD
≤ 5.5V
-0.5 -0.1 — LSb 100 kΩ 8-bit 3.0V ≤ V
DD
≤ 5.5V
-0.5 -0.1 — LSb 7-bit 3.0V ≤ V
DD
≤ 5.5V
Zero-Scale Error
(MCP4XX1 only)
(8-bit code = 00h,
7-bit code = 00h)
V
WZSE
—+0.1+6.0LSb5kΩ 8-bit 3.0V ≤ V
DD
≤ 5.5V
— +0.1 +3.0 LSb 7-bit 3.0V ≤ V
DD
≤ 5.5V
— +0.1 +3.5 LSb 10 kΩ 8-bit 3.0V ≤ V
DD
≤ 5.5V
— +0.1 +2.0 LSb 7-bit 3.0V ≤ V
DD
≤ 5.5V
— +0.1 +0.8 LSb 50 kΩ 8-bit 3.0V ≤ V
DD
≤ 5.5V
— +0.1 +0.5 LSb 7-bit 3.0V ≤ V
DD
≤ 5.5V
— +0.1 +0.5 LSb 100 kΩ 8-bit 3.0V ≤ V
DD
≤ 5.5V
— +0.1 +0.5 LSb 7-bit 3.0V ≤ V
DD
≤ 5.5V
Potentiometer
Integral
Non-linearity
INL -1 ±0.5 +1 LSb 8-bit 3.0V ≤ V
DD
≤ 5.5V
MCP4XX1 devices only
(Note 2)
-0.5 ±0.25 +0.5 LSb 7-bit
Potentiometer
Differential
Non-linearity
DNL -0.5 ±0.25 +0.5 LSb 8-bit 3.0V ≤ V
DD
≤ 5.5V
MCP4XX1 devices only
(Note 2)
-0.25 ±0.125 +0.25 LSb 7-bit
Bandwidth -3 dB
(See Figure 2-58,
load = 30 pF)
BW — 2 — MHz 5 kΩ 8-bit Code = 80h
— 2 — MHz 7-bit Code = 40h
—1—MHz10kΩ 8-bit Code = 80h
— 1 — MHz 7-bit Code = 40h
—200—kHz50kΩ 8-bit Code = 80h
— 200 — kHz 7-bit Code = 40h
—100—kHz100kΩ 8-bit Code = 80h
— 100 — kHz 7-bit Code = 40h
AC/DC CHARACTERISTICS (CONTINUED)
DC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature –40°C ≤ T
A
≤ +125°C (extended)
All parameters apply across the specified operating ranges unless noted.
V
DD
= +2.7V to 5.5V, 5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ devices.
Typical specifications represent values for V
DD
= 5.5V, T
A
= +25°C.
Parameters Sym Min Typ Max Units Conditions
Note 1: Resistance is defined as the resistance between terminal A to terminal B.
2: INL and DNL are measured at V
W
with V
A
= V
DD
and V
B
= V
SS
.
3: MCP4XX1 only.
4: MCP4XX2 only, includes V
WZSE
and V
WFSE
.
5: Resistor terminals A, W and B’s polarity with respect to each other is not restricted.
6: This specification by design.
7: Non-linearity is affected by wiper resistance (R
W
), which changes significantly over voltage and
temperature.
8: The MCP4XX1 is externally connected to match the configurations of the MCP41X2 and MCP42X2, and
then tested.
9: POR/BOR is not rate dependent.
10: Supply current is independent of current through the resistor network