Datasheet
Table Of Contents
- Features
- Applications
- Description
- Package Types
- Functional Block Diagram
- 1.0 Electrical Characteristics
- PIN FUNCTION TABLE
- electrical characteristics
- 2.0 Typical Performance Characteristics
- FIGURE 2-1: Integral Nonlinearity (INL) vs. Sample Rate.
- FIGURE 2-2: Integral Nonlinearity (INL) vs. Vref.
- FIGURE 2-3: Integral Nonlinearity (INL) vs. Code (Representative Part).
- FIGURE 2-4: Integral Nonlinearity (INL) vs. Sample Rate (Vdd = 2.7V).
- FIGURE 2-5: Integral Nonlinearity (INL) vs. Vref (Vdd = 2.7V).
- FIGURE 2-6: Integral Nonlinearity (INL) vs. Code (Representative Part, Vdd = 2.7V).
- FIGURE 2-7: Integral Nonlinearity (INL) vs. Temperature.
- FIGURE 2-8: Differential Nonlinearity (DNL) vs. Sample Rate.
- FIGURE 2-9: Differential Nonlinearity (DNL) vs. Vref.
- FIGURE 2-10: Integral Nonlinearity (INL) vs. Temperature (Vdd = 2.7V).
- FIGURE 2-11: Differential Nonlinearity (DNL) vs. Sample Rate (Vdd = 2.7V).
- FIGURE 2-12: Differential Nonlinearity (DNL) vs. Vref (Vdd = 2.7V).
- FIGURE 2-13: Differential Nonlinearity (DNL) vs. Code (Representative Part).
- FIGURE 2-14: Differential Nonlinearity (DNL) vs. Temperature.
- FIGURE 2-15: Gain Error vs. Vref.
- FIGURE 2-16: Differential Nonlinearity (DNL) vs. Code (Representative Part, Vdd = 2.7V).
- FIGURE 2-17: Differential Nonlinearity (DNL) vs. Temperature (Vdd = 2.7V).
- FIGURE 2-18: Offset Error vs. Vref.
- FIGURE 2-19: Gain Error vs. Temperature.
- FIGURE 2-20: Signal to Noise Ratio (SNR) vs. Input Frequency.
- FIGURE 2-21: Total Harmonic Distortion (THD) vs. Input Frequency.
- FIGURE 2-22: Offset Error vs. Temperature.
- FIGURE 2-23: Signal to Noise Ratio and Distortion (SINAD) vs. Input Frequency.
- FIGURE 2-24: Signal to Noise and Distortion (SINAD) vs. Input Signal Level.
- FIGURE 2-25: Effective Number of Bits (ENOB) vs. Vref.
- FIGURE 2-26: Spurious Free Dynamic Range (SFDR) vs. Input Frequency.
- FIGURE 2-27: Frequency Spectrum of 10kHz Input (Representative Part).
- FIGURE 2-28: Effective Number of Bits (ENOB) vs. Input Frequency.
- FIGURE 2-29: Power Supply Rejection (PSR) vs. Ripple Frequency.
- FIGURE 2-30: Frequency Spectrum of 1kHz Input (Representative Part, Vdd = 2.7V).
- FIGURE 2-31: Idd vs. Vdd.
- FIGURE 2-32: Idd vs. Clock Frequency.
- FIGURE 2-33: Idd vs. Temperature.
- FIGURE 2-34: Iref vs. Vdd.
- FIGURE 2-35: Iref vs. Clock Frequency.
- FIGURE 2-36: Iref vs. Temperature.
- FIGURE 2-37: Idds vs. Vdd.
- FIGURE 2-38: Idds vs. Temperature.
- FIGURE 2-39: Analog Input Leakage Current vs. Temperature.
- 3.0 Pin Descriptions
- 4.0 Device Operation
- 5.0 Serial Communications
- 6.0 Applications Information
- 7.0 Packaging Information
- Appendix A: Revision History
- Product Identification System
- Worldwide Sales and Service
© 2007 Microchip Technology Inc. DS21293C-page 19
MCP3001
8-Lead Plastic Dual In-Line (P) – 300 mil Body [PDIP]
N
otes:
1
. Pin 1 visual index feature may vary, but must be located with the hatched area.
2
. § Significant Characteristic.
3
. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" per side.
4
. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
Units INCHES
Dimension Limits MIN NOM MAX
Number of Pins N 8
Pitch e .100 BSC
Top to Seating Plane A – – .210
Molded Package Thickness A2 .115 .130 .195
Base to Seating Plane A1 .015 – –
Shoulder to Shoulder Width E .290 .310 .325
Molded Package Width E1 .240 .250 .280
Overall Length D .348 .365 .400
Tip to Seating Plane L .115 .130 .150
Lead Thickness c .008 .010 .015
Upper Lead Width b1 .040 .060 .070
Lower Lead Width b .014 .018 .022
Overall Row Spacing § eB – – .430
N
E1
NOTE 1
D
12
3
A
A1
A2
L
b1
b
e
E
eB
c
Microchip Technology Drawing C04-018
B