Datasheet
2011-2012 Microchip Technology Inc. DS70652E-page 29
dsPIC33FJ16(GP/MC)101/102 AND dsPIC33FJ32(GP/MC)101/102/104
TABLE 1-1: PINOUT I/O DESCRIPTIONS
Pin Name
Pin
Type
Buffer
Type
PPS Description
AN0-AN12,
AN15
(5)
I Analog No Analog input channels.
CLKI
CLKO
I
O
ST/CMOS
—
No
No
External clock source input. Always associated with OSC1 pin function.
Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator
mode. Optionally functions as CLKO in RC and EC modes. Always
associated with OSC2 pin function.
OSC1
OSC2
I
I/O
ST/CMOS
—
No
No
Oscillator crystal input. ST buffer when configured in RC mode; CMOS
otherwise.
Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator
mode. Optionally functions as CLKO in RC and EC modes.
SOSCI
SOSCO
I
O
ST/CMOS
—
No
No
32.768 kHz low-power oscillator crystal input; CMOS otherwise.
32.768 kHz low-power oscillator crystal output.
CN0-CN30
(5)
I ST No Change Notification inputs. Can be software programmed for internal weak
pull-ups on all inputs.
IC1-IC3 I ST Yes Capture Inputs 1/2/3.
OCFA
OC1-OC2
I
O
ST
—
Yes
Yes
Compare Fault A input (for Compare Channels 1 and 2).
Compare Outputs 1 through 2.
INT0
INT1
INT2
I
I
I
ST
ST
ST
No
Yes
Yes
External Interrupt 0.
External Interrupt 1.
External Interrupt 2.
RA0-RA4,
RA7-RA10
(5)
I/O ST No PORTA is a bidirectional I/O port.
RB0-RB15
(5)
I/O ST No PORTB is a bidirectional I/O port.
RC0-RC9
(5)
I/O ST No PORTC is a bidirectional I/O port.
T1CK
T2CK
T3CK
T4CK
(6)
T5CK
(6)
I
I
I
I
I
ST
ST
ST
ST
ST
No
Yes
Yes
Yes
Yes
Timer1 external clock input.
Timer2 external clock input.
Timer3 external clock input.
Timer4 external clock input.
Timer5 external clock input.
U1CTS
U1RTS
U1RX
U1TX
I
O
I
O
ST
—
ST
—
Yes
Yes
Yes
Yes
UART1 Clear-to-Send.
UART1 Ready-to-Send.
UART1 receive.
UART1 transmit.
SCK1
SDI1
SDO1
I/O
I
O
ST
ST
—
Yes
Yes
Yes
Synchronous serial clock input/output for SPI1.
SPI1 data in.
SPI1 data out.
Legend: CMOS = CMOS compatible input or output Analog = Analog input P = Power
ST = Schmitt Trigger input with CMOS levels O = Output I = Input
PPS = Peripheral Pin Select
Note 1: An external pull-down resistor is required for the FLTA1
pin on dsPIC33FJXXMC101 (20-pin) devices.
2: The FLTA1
pin and the PWM1Lx/PWM1Hx pins are available in dsPIC(16/32)MC10X devices only.
3: The FLTB1
pin is available in dsPIC(16/32)MC102/104 devices only.
4: The PWM Fault pins are enabled during any Reset event. Refer to Section 15.2 “PWM Faults” for more
information on the PWM Faults.
5: Not all pins are available on all devices. Refer to the specific device in the “Pin Diagrams” section for
availability.
6: This pin is available in dsPIC33FJ32(GP/MC)104 (44-pin) devices only.