Datasheet
© 2008-2012 Microchip Technology Inc. DS70318F-page 323
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-38: I2Cx BUS DATA TIMING REQUIREMENTS (MASTER MODE)
AC CHARACTERISTICS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ T
A ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
Param
No.
Symbol Characteristic Min
(1)
Max Units Conditions
IM10 T
LO:SCL Clock Low Time 100 kHz mode TCY/2 (BRG + 1) — μs—
400 kHz mode TCY/2 (BRG + 1) — μs—
1 MHz mode
(2)
TCY/2 (BRG + 1) — μs—
IM11 THI:SCL Clock High Time 100 kHz mode TCY/2 (BRG + 1) — μs—
400 kHz mode TCY/2 (BRG + 1) — μs—
1 MHz mode
(2)
TCY/2 (BRG + 1) — μs—
IM20 TF:SCL SDAx and SCLx
Fall Time
100 kHz mode — 300 ns CB is specified to be
from 10 pF to 400 pF
400 kHz mode 20 + 0.1 CB 300 ns
1 MHz mode
(2)
— 100 ns
IM21 TR:SCL SDAx and SCLx
Rise Time
100 kHz mode — 1000 ns CB is specified to be
from 10 pF to 400 pF
400 kHz mode 20 + 0.1 CB 300 ns
1 MHz mode
(2)
— 300 ns
IM25 TSU:DAT Data Input
Setup Time
100 kHz mode 250 — ns —
400 kHz mode 100 — ns —
1 MHz mode
(2)
40 — ns —
IM26 THD:DAT Data Input
Hold Time
100 kHz mode 0 — μs—
400 kHz mode 0 0.9 μs—
1 MHz mode
(2)
0.2 — μs—
IM30 TSU:STA Start Condition
Setup Time
100 kHz mode TCY/2 (BRG + 1) — μs Only relevant for
Repeated Start
condition
400 kHz mode TCY/2 (BRG + 1) — μs
1 MHz mode
(2)
TCY/2 (BRG + 1) — μs
IM31 THD:STA Start Condition
Hold Time
100 kHz mode TCY/2 (BRG + 1) — μs After this period the
first clock pulse is
generated
400 kHz mode T
CY/2 (BRG + 1) — μs
1 MHz mode
(2)
TCY/2 (BRG + 1) — μs
IM33 TSU:STO Stop Condition
Setup Time
100 kHz mode TCY/2 (BRG + 1) — μs—
400 kHz mode TCY/2 (BRG + 1) — μs—
1 MHz mode
(2)
TCY/2 (BRG + 1) — μs—
IM34 T
HD:STO Stop Condition 100 kHz mode TCY/2 (BRG + 1) — ns —
Hold Time 400 kHz mode TCY/2 (BRG + 1) — ns —
1 MHz mode
(2)
TCY/2 (BRG + 1) — ns —
IM40 TAA:SCL Output Valid
From Clock
100 kHz mode — 3500 ns —
400 kHz mode — 1000 ns —
1 MHz mode
(2)
— 400 ns —
IM45 TBF:SDA Bus Free Time 100 kHz mode 4.7 — μs Time the bus must be
free before a new
transmission can start
400 kHz mode 1.3 — μs
1 MHz mode
(2)
0.5 — μs
IM50 C
B Bus Capacitive Loading — 400 pF —
IM51 TPGD Pulse Gobbler Delay 65 390 ns See Note 3
Note 1: BRG is the value of the I
2
C™ Baud Rate Generator. Refer to Section 19. “Inter-Integrated Circuit
(I
2
C™)” (DS70195) in the “dsPIC33F/PIC24H Family Reference Manual”.
2: Maximum pin capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only).
3: Typical value for this parameter is 130 ns.