Datasheet

 2011-2013 Microchip Technology Inc. DS70657G-page 451
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X AND PIC24EPXXXGP/MC20X
TABLE 30-50: I2Cx BUS DATA TIMING REQUIREMENTS (SLAVE MODE)
AC CHARACTERISTICS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  T
A  +125°C for
Extended
Param.
No.
Symbol Characteristic
(3)
Min. Max. Units Conditions
IS10 T
LO:SCL Clock Low Time 100 kHz mode 4.7 — s
400 kHz mode 1.3 — s
1 MHz mode
(1)
0.5 — s
IS11 THI:SCL Clock High Time 100 kHz mode 4.0 — s Device must operate at a
minimum of 1.5 MHz
400 kHz mode 0.6 — s Device must operate at a
minimum of 10 MHz
1 MHz mode
(1)
0.5 — s
IS20 T
F:SCL SDAx and SCLx
Fall Time
100 kHz mode — 300 ns CB is specified to be from
10 to 400 pF
400 kHz mode 20 + 0.1 CB 300 ns
1 MHz mode
(1)
—100ns
IS21 T
R:SCL SDAx and SCLx
Rise Time
100 kHz mode — 1000 ns CB is specified to be from
10 to 400 pF
400 kHz mode 20 + 0.1 CB 300 ns
1 MHz mode
(1)
—300ns
IS25 T
SU:DAT Data Input
Setup Time
100 kHz mode 250 — ns
400 kHz mode 100 — ns
1 MHz mode
(1)
100 — ns
IS26 T
HD:DAT Data Input
Hold Time
100 kHz mode 0 — s
400 kHz mode 0 0.9 s
1 MHz mode
(1)
00.3s
IS30 TSU:STA Start Condition
Setup Time
100 kHz mode 4.7 — s Only relevant for Repeated
Start condition
400 kHz mode 0.6 — s
1 MHz mode
(1)
0.25 — s
IS31 THD:STA Start Condition
Hold Time
100 kHz mode 4.0 — s After this period, the first
clock pulse is generated
400 kHz mode 0.6 — s
1 MHz mode
(1)
0.25 — s
IS33 TSU:STO Stop Condition
Setup Time
100 kHz mode 4.7 — s
400 kHz mode 0.6 — s
1 MHz mode
(1)
0.6 — s
IS34 T
HD:STO Stop Condition
Hold Time
100 kHz mode 4 — s
400 kHz mode 0.6 — s
1 MHz mode
(1)
0.25 s
IS40 T
AA:SCL Output Valid
From Clock
100 kHz mode 0 3500 ns
400 kHz mode 0 1000 ns
1 MHz mode
(1)
0350ns
IS45 T
BF:SDA Bus Free Time 100 kHz mode 4.7 — s Time the bus must be free
before a new transmission
can start
400 kHz mode 1.3 — s
1 MHz mode
(1)
0.5 — s
IS50 CB Bus Capacitive Loading — 400 pF
IS51 T
PGD Pulse Gobbler Delay 65 390 ns (Note 2)
Note 1: Maximum pin capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only).
2: Typical value for this parameter is 130 ns.
3: These parameters are characterized, but not tested in manufacturing.