Datasheet

PIC24FJ128GC010 FAMILY
DS30009312B-page 102  2012-2013 Microchip Technology Inc.
TABLE 7-3: RESET DELAY TIMES FOR VARIOUS DEVICE RESETS
7.4.1 POR AND LONG OSCILLATOR
START-UP TIMES
The oscillator start-up circuitry and its associated delay
timers are not linked to the device Reset delays that
occur at power-up. Some crystal circuits (especially
low-frequency crystals) will have a relatively long
start-up time. Therefore, one or more of the following
conditions is possible after SYSRST
is released:
• The oscillator circuit has not begun to oscillate.
• The Oscillator Start-up Timer has not expired (if a
crystal oscillator is used).
• The PLL has not achieved a lock (if PLL is used).
The device will not begin to execute code until a valid
clock source has been released to the system. There-
fore, the oscillator and PLL start-up delays must be
considered when the Reset delay time must be known.
7.4.2 FAIL-SAFE CLOCK MONITOR
(FSCM) AND DEVICE RESETS
If the FSCM is enabled, it will begin to monitor the
system clock source when SYSRST
is released. If a
valid clock source is not available at this time, the
device will automatically switch to the FRC oscillator
and the user can switch to the desired crystal oscillator
in the Trap Service Routine (TSR).
Reset Type Clock Source SYSRST
Delay
System Clock
Delay
Notes
POR EC T
POR + TSTARTUP + TRST — 1, 2, 3
ECPLL T
POR + TSTARTUP + TRST TLOCK 1, 2, 3, 5
XT, HS, SOSC T
POR + TSTARTUP + TRST TOST 1, 2, 3, 4
XTPLL, HSPLL TPOR + TSTARTUP + TRST TOST + TLOCK 1, 2, 3, 4, 5
FRC, FRCDIV TPOR + TSTARTUP + TRST TFRC 1, 2, 3, 6, 7
FRCPLL T
POR + TSTARTUP + TRST TFRC + TLOCK 1, 2, 3, 5, 6
LPRC TPOR + TSTARTUP + TRST TLPRC 1, 2, 3, 6
BOR EC TSTARTUP + TRST — 2, 3
ECPLL T
STARTUP + TRST TLOCK 2, 3, 5
XT, HS, SOSC TSTARTUP + TRST TOST 2, 3, 4
XTPLL, HSPLL TSTARTUP + TRST TOST + TLOCK 2, 3, 4, 5
FRC, FRCDIV T
STARTUP + TRST TFRC 2, 3, 6, 7
FRCPLL TSTARTUP + TRST TFRC + TLOCK 2, 3, 5, 6
LPRC TSTARTUP + TRST TLPRC 2, 3, 6
MCLR
Any Clock TRST — 3
WDT Any Clock T
RST — 3
Software Any clock TRST — 3
Illegal Opcode Any Clock TRST — 3
Uninitialized W Any Clock T
RST — 3
Trap Conflict Any Clock TRST — 3
Note 1: TPOR = Power-on Reset delay (10 s nominal).
2: TSTARTUP = TVREG.
3: TRST = Internal State Reset time (2 s nominal).
4: T
OST = Oscillator Start-up Timer (OST). A 10-bit counter counts 1024 oscillator periods before releasing
the oscillator clock to the system.
5: T
LOCK = PLL lock time.
6: TFRC and TLPRC = RC oscillator start-up times.
7: If Two-Speed Start-up is enabled, regardless of the primary oscillator selected, the device starts with FRC,
so the system clock delay is just T
FRC and in such cases, FRC start-up time is valid. It switches to the
primary oscillator after its respective clock delay.