User's Manual

ManualsBrandsMicrochip Technology ManualsElectronicsBTLC1000-MR110CA

Atmel-42376B-BTLC1000-MR210P-SmartConnect-Datasheet_02102015

Atmel BTLC1000-MR110CA

User Manual

Description

The BTLC1000-MR110CA is an ultra-low power Bluetooth

SMART (BLE 4.1) module with

Integrated Transceiver, Modem, MAC, PA, TR Switch, and Power Management Unit (PMU). It can

be used as a Bluetooth Low Energy link controller or data pump with external host MCU.

The qualified Bluetooth

Smart protocol stack is stored in dedicated ROM, the firmware includes

L2CAP service layer protocols, Security Manager, Attribute protocol (ATT), Generic Attribute Profile

(GATT) and the Generic Access Profile (GAP). Additionally, application profiles such as Proximity,

Thermometer, Heart Rate, Blood Pressure and many others are supported and included in the

protocol stack.

The module contains all circuitry required including a ceramic high gain antenna, 26MHz crystal

and PMU circuitry. The customer simply needs to place the module on his board and provide

power.

Table of Contents

Description .......................................................................................................................... 1

1 Electrical Specifications ............................................................................................... 2

1.1

Absolute Maximum Ratings ...................................................................................................................... 2

1.2

Recommended Operating Conditions ....................................................................................................... 2

1.3

Restrictions for Power States ................................................................................................................... 3

1.4

Power-Up Sequence ................................................................................................................................. 3

2 Application Information ................................................................................................ 4

3 Placement and Routing Guidelines ............................................................................. 4

3.1

Power and Ground.................................................................................................................................... 4

4 FCC Information ............................................................................................................ 5

5 Interferers ...................................................................................................................... 5

List of Figures

Figure 1: Power-Up Sequence............................................................................................................................................ 3

Summary of content (6 pages)

PAGE 1
Atmel BTLC1000-MR110CA User Manual Description The BTLC1000-MR110CA is an ultra-low power Bluetooth® SMART (BLE 4.1) module with Integrated Transceiver, Modem, MAC, PA, TR Switch, and Power Management Unit (PMU). It can be used as a Bluetooth Low Energy link controller or data pump with external host MCU.
PAGE 2
1 Electrical Specifications 1.1 Absolute Maximum Ratings Table 1: BTLC1000-MR110CA Absolute Maximum Ratings Symbol Characteristic Min Max Unit VDDIO I/O Supply Voltage -0.3 4.6 V VBATT Battery Supply Voltage -0.3 5.0 V VIN(1) Digital Input Voltage -0.3 VDDIO V VAIN(2) Analog Input Voltage -0.3 1.5 V VESDHBM(3) ESD Human Body Model -1000, -2000 (see notes below) +1000, +2000 (see notes below) V TA Storage Temperature -65 150 oC 125 oC Junction Temperature Notes: 1.
PAGE 3
Notes: 1. VBATT supply must be greater than or equal to VDDIO 1.3 Restrictions for Power States When VDDIO is off (either disconnected or at ground potential), a voltage must not be applied to the device pins. This is because each pin contains an ESD diode from the pin to the VDDIO supply. This diode will turn on when a voltage higher than one diode-drop is supplied to the pin. This in turn will try to power up the part through the VDDIO supply.
PAGE 4
Parameter Min Max Units Description Notes tBIO 0 ms VBATT rise to VDDIO rise VBATT and VDDIO can rise simultaneously or can be tied together. tIOCE 0 ms VDDIO rise to CHIP_EN rise CHIP_EN must not rise before VDDIO. CHIP_EN must be driven high or low, not left floating. 2 Application Information The BTLC1000-MR110 module is fully self-contained. To use the module, just provide VBAT and VDDIO supplies. See Table 2 for the recommended voltages.
PAGE 5
4 FCC Information Each module has a label with an FCC ID, however the product User Manual must contain the following statement: “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation”.
PAGE 6
BTLC1000-MR110CA [DATA SHEET] Atmel-42376B-BTLC1000 Hardware Design Guide_02102015