Datasheet
Table Of Contents
- Features
- 1. Ordering Information
- 2. Pinout/Block Diagram
- 3. Overview
- 4. Resources
- 5. Capacitive touch sensing
- 6. AVR CPU
- 7. Memories
- 8. Event System
- 9. System Clock and Clock options
- 9.1 Features
- 9.2 Overview
- 9.3 Clock Sources
- 9.3.1 32kHz Ultra Low Power Internal Oscillator
- 9.3.2 32.768kHz Calibrated Internal Oscillator
- 9.3.3 32.768kHz Crystal Oscillator
- 9.3.4 0.4 - 16MHz Crystal Oscillator
- 9.3.5 2MHz Run-time Calibrated Internal Oscillator
- 9.3.6 32MHz Run-time Calibrated Internal Oscillator
- 9.3.7 External Clock Sources
- 9.3.8 PLL with 1x-31x Multiplication Factor
- 10. Power Management and Sleep Modes
- 11. System Control and Reset
- 12. WDT – Watchdog Timer
- 13. Interrupts and Programmable Multilevel Interrupt Controller
- 14. I/O Ports
- 15. TC0/1 – 16-bit Timer/Counter Type 0 and 1
- 16. TC2 – Timer/Counter Type 2
- 17. AWeX – Advanced Waveform Extension
- 18. Hi-Res – High Resolution Extension
- 19. RTC – 16-bit Real-Time Counter
- 20. USB – Universal Serial Bus Interface
- 21. TWI – Two-Wire Interface
- 22. SPI – Serial Peripheral Interface
- 23. USART
- 24. IRCOM – IR Communication Module
- 25. CRC – Cyclic Redundancy Check Generator
- 26. ADC – 12-bit Analog to Digital Converter
- 27. AC – Analog Comparator
- 28. Programming and Debugging
- 29. Pinout and Pin Functions
- 30. Peripheral Module Address Map
- 31. Instruction Set Summary
- 32. Packaging information
- 33. Electrical Characteristics TBD
- 34. Typical Characteristics TBD
- 35. Errata
- 36. Datasheet Revision History
- Table of Contents
62
8493A–AVR–02/12
XMEGA C4
32. Packaging information
32.1 64A
2325 Orchard Parkway
San Jose, CA 95131
TITLE
DRAWING NO.
R
REV.
64A, 64-lead, 14 x 14mm Body Size, 1.0mm Body Thickness,
0.8mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
C
64A
2010-10-20
PIN 1 IDENTIFIER
0°~7°
PIN 1
L
C
A1
A2 A
D1
D
e
E1 E
B
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
MIN
NOM
MAX
NOTE
Notes:
1.This package conforms to JEDEC reference MS-026, Variation AEB.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
3. Lead coplanarity is 0.10mm maximum.
A – – 1.20
A1 0.05 – 0.15
A2 0.95 1.00 1.05
D 15.75 16.00 16.25
D1 13.90 14.00 14.10 Note 2
E 15.75 16.00 16.25
E1 13.90 14.00 14.10 Note 2
B 0.30 – 0.45
C 0.09 – 0.20
L 0.45 – 0.75
e 0.80 TYP