Datasheet

421
XMEGA D3 [DATASHEET]
Atmel-8134N-ATxmega32D3-64D3-128D3-192D3-256D3-384D3_datasheet–03/2014
35.5 8134J – 03/2013
1. Almost all figures in Chapter “Typical characteristics” are updated.
2. Added new Errata “Rev. G” on page 117.
3. Added new Errata “Rev. B” on page 125 and “Rev. E” on page 118. Non available functions and options.
4. Editing updates.
5. Added ATxmega32D3 and ATxmega384D3.
6. New datasheet template is added.
7. A lot of small corrections and a complete reorganization of “Electrical characteristics” and “Typical characteristics” .
8. Bullet “Optional Slew Rate Control” in Chapter “I/O ports” on page 29 is removed
9. The sentence “The port pins also have configurable slew rate limitation to reduce electromagnetic emission” in
Chapter “I/O ports” on page 29 is removed.
10. The sentence “The I/O pins complies with the JEDEC LVTTL and LVCMOS specification and the high- and low
level input and output voltage limits reflect or exceed this specification” is added to Section 32.1.5 on page 68,
Section 32.2.5 on page 87, Section 32.6.5 on page 163, Section 33.3.2 on page 228, Section 33.4.2 on page
262, Section 33.5.2 on page 296 and Section 33.6.2 on page 330.
11. Figure 2-1 on page 4 is updated by changing VDD to VCC.
12. Table 7-1 on page 14 is updated.
13. Figure 7-2 on page 15 is updated.
14. Figure 14-7 on page 32 is updated.
15. Former Table 32-24, Table 32-52, Table 32-79, Table 32-107, Table 32-135, Table 32-163 (title: “External clock”) have
each been replaced by two new tables, named respectively “External clock used as system clock without prescaling”
and “External clock with prescaler for system clock”.
16. In Table 32-29 on page 81, Table 32-58 on page 100, Table 32-87 on page 119, Table 32-116 on page 138, Table
32-145 on page 157, and Table 32-174 on page 176 the value for the parameter “Input voltage” has been corrected.
17. In Table 32-18 on page 73, Table 32-47 on page 92, Table 32-76 on page 111, Table 32-105 on page 130, Table 32-
134 on page 149, and Table 32-163 on page 168 the parameter “Application erase” has been added.
18. Table 32-14 on page 72, Table 32-43 on page 91, Table 32-101 on page 129, Table 32-130 on page 148 and Table
32-159 on page 167 (Brownout detection characteristics) are updated.
19. Table 32-20 on page 74 and Table 32-49 on page 93 (2MHz internal oscillator characteristics) are updated.
20. Table 32-21 on page 74 and Table 32-50 on page 93 (32MHz internal oscillator characteristics) are updated.
21. Accuracy added in Table 32-109 on page 131.
22. Table 32-149 on page 160 has been corrected.
23 Table 32-167 on page 169; “Factory calibration accuracy” and “Accuracy” is added.
24. Table 32-150 on page 161, Table 32-152 on page 163, Table 32-154 on page 164, Table 32-155 on page 165, Table
32-156 on page 166, and Table 32-157 on page 166 has been updated.
25. Section 1. “Ordering information” on page 2 is updated
26. Former Section 31.3 “64Z3” has been removed.
27. Section 31.2 “64M” on page 62 has replaced the former Section 31.2 “64M2”.