Datasheet

ManualsBrandsMICROCHIP TECHNOLOGY ManualsMicrocontrollers, Microprocessors & QuartzesEmbedded microcontroller QFN 20 (4x4) 8-Bit 20 MHz I/O number 12

Table Of Contents

Features
1. Pin Configurations
- 1.1 Pin Descriptions
2. Overview
3. About
- 3.1 Resources
- 3.2 Code Examples
- 3.3 Data Retention
- 3.4 Disclaimer
4. CPU Core
- 4.1 Architectural Overview
- 4.2 ALU – Arithmetic Logic Unit
- 4.3 Status Register
  - 4.3.1 SREG – AVR Status Register
- 4.4 General Purpose Register File
  - 4.4.1 The X-register, Y-register, and Z-register
- 4.5 Stack Pointer
  - 4.5.1 SPH and SPL — Stack Pointer Register
- 4.6 Instruction Execution Timing
- 4.7 Reset and Interrupt Handling
  - 4.7.1 Interrupt Response Time
5. Memories
- 5.1 In-System Re-programmable Flash Program Memory
- 5.2 SRAM Data Memory
  - 5.2.1 Data Memory Access Times
- 5.3 EEPROM Data Memory
- 5.4 I/O Memory
  - 5.4.1 General Purpose I/O Registers
- 5.5 Register Description
6. Clock System
- 6.1 Clock Subsystems
- 6.2 Clock Sources
- 6.3 System Clock Prescaler
  - 6.3.1 Switching Time
- 6.4 Clock Output Buffer
- 6.5 Register Description
  - 6.5.1 OSCCAL – Oscillator Calibration Register
  - 6.5.2 CLKPR – Clock Prescale Register
7. Power Management and Sleep Modes
- 7.1 Sleep Modes
- 7.2 Software BOD Disable
  - 7.2.1 Limitations
- 7.3 Power Reduction Register
- 7.4 Minimizing Power Consumption
- 7.5 Register Description
  - 7.5.1 MCUCR – MCU Control Register
  - 7.5.2 PRR – Power Reduction Register
8. System Control and Reset
- 8.1 Resetting the AVR
- 8.2 Reset Sources
- 8.3 Internal Voltage Reference
  - 8.3.1 Voltage Reference Enable Signals and Start-up Time
- 8.4 Watchdog Timer
  - 8.4.1 Timed Sequences for Changing the Configuration of the Watchdog Timer
    - 8.4.1.1 Safety Level 1
    - 8.4.1.2 Safety Level 2
  - 8.4.2 Code Example
- 8.5 Register Description
  - 8.5.1 MCUSR – MCU Status Register
  - 8.5.2 WDTCSR – Watchdog Timer Control and Status Register
9. Interrupts
- 9.1 Interrupt Vectors
- 9.2 External Interrupts
  - 9.2.1 Low Level Interrupt
  - 9.2.2 Pin Change Interrupt Timing
- 9.3 Register Description
10. I/O Ports
- 10.1 Ports as General Digital I/O
- 10.2 Alternate Port Functions
  - 10.2.1 Alternate Functions of Port A
  - 10.2.2 Alternate Functions of Port B
- 10.3 Register Description
11. 8-bit Timer/Counter0 with PWM
- 11.1 Features
- 11.2 Overview
  - 11.2.1 Registers
  - 11.2.2 Definitions
- 11.3 Clock Sources
- 11.4 Counter Unit
- 11.5 Output Compare Unit
- 11.6 Compare Match Output Unit
  - 11.6.1 Compare Output Mode and Waveform Generation
- 11.7 Modes of Operation
- 11.8 Timer/Counter Timing Diagrams
- 11.9 Register Description
12. 16-bit Timer/Counter1
- 12.1 Features
- 12.2 Overview
- 12.3 Timer/Counter Clock Sources
- 12.4 Counter Unit
- 12.5 Input Capture Unit
- 12.6 Output Compare Units
- 12.7 Compare Match Output Unit
  - 12.7.1 Compare Output Mode and Waveform Generation
- 12.8 Modes of Operation
- 12.9 Timer/Counter Timing Diagrams
- 12.10 Accessing 16-bit Registers
  - 12.10.1 Reusing the Temporary High Byte Register
- 12.11 Register Description
13. Timer/Counter Prescaler
- 13.1 Prescaler Reset
- 13.2 External Clock Source
- 13.3 Register Description
  - 13.3.1 GTCCR – General Timer/Counter Control Register
14. USI – Universal Serial Interface
- 14.1 Features
- 14.2 Overview
- 14.3 Functional Descriptions
- 14.4 Alternative USI Usage
- 14.5 Register Descriptions
15. Analog Comparator
- 15.1 Analog Comparator Multiplexed Input
- 15.2 Register Description
16. Analog to Digital Converter
- 16.1 Features
- 16.2 Overview
- 16.3 Operation
- 16.4 Starting a Conversion
- 16.5 Prescaling and Conversion Timing
- 16.6 Changing Channel or Reference Selection
  - 16.6.1 ADC Input Channels
  - 16.6.2 ADC Voltage Reference
- 16.7 ADC Noise Canceler
- 16.8 Analog Input Circuitry
- 16.9 Noise Canceling Techniques
- 16.10 ADC Accuracy Definitions
- 16.11 ADC Conversion Result
- 16.12 Temperature Measurement
- 16.13 Register Description
17. debugWIRE On-chip Debug System
- 17.1 Features
- 17.2 Overview
- 17.3 Physical Interface
- 17.4 Software Break Points
- 17.5 Limitations of debugWIRE
- 17.6 Register Description
  - 17.6.1 DWDR – debugWire Data Register
18. Self-Programming the Flash
- 18.1 Performing Page Erase by SPM
- 18.2 Filling the Temporary Buffer (Page Loading)
- 18.3 Performing a Page Write
- 18.4 Addressing the Flash During Self-Programming
- 18.5 EEPROM Write Prevents Writing to SPMCSR
- 18.6 Reading Lock, Fuse and Signature Data from Software
- 18.7 Preventing Flash Corruption
- 18.8 Programming Time for Flash when Using SPM
- 18.9 Register Description
  - 18.9.1 SPMCSR – Store Program Memory Control and Status Register
19. Memory Programming
- 19.1 Program And Data Memory Lock Bits
- 19.2 Fuse Bytes
  - 19.2.1 Latching of Fuses
- 19.3 Device Signature Imprint Table
  - 19.3.1 Signature Bytes
  - 19.3.2 Calibration Byte
- 19.4 Page Size
- 19.5 Serial Programming
  - 19.5.1 Serial Programming Algorithm
  - 19.5.2 Serial Programming Instruction set
- 19.6 High-voltage Serial Programming
- 19.7 High-Voltage Serial Programming Algorithm
20. Electrical Characteristics
- 20.1 Absolute Maximum Ratings*
- 20.2 DC Characteristics
- 20.3 Speed
- 20.4 Clock Characteristics
  - 20.4.1 Accuracy of Calibrated Internal RC Oscillator
  - 20.4.2 External Clock Drive
- 20.5 System and Reset Characteristics
- 20.6 Analog Comparator Characteristics
- 20.7 ADC Characteristics
- 20.8 Serial Programming Characteristics
- 20.9 High-Voltage Serial Programming Characteristics
21. Typical Characteristics
- 21.1 Supply Current of I/O Modules
  - 21.1.1 Example
- 21.2 Active Supply Current
- 21.3 Idle Supply Current
- 21.4 Power-down Supply Current
- 21.5 Standby Supply Current
- 21.6 Pin Pull-up
- 21.7 Pin Driver Strength
- 21.8 Pin Threshold and Hysteresis
- 21.9 BOD Threshold and Analog Comparator Offset
- 21.10 Internal Oscillator Speed
- 21.11 Current Consumption of Peripheral Units
- 21.12 Current Consumption in Reset and Reset Pulsewidth
22. Register Summary
23. Instruction Set Summary
24. Ordering Information
- 24.1 ATtiny24
- 24.2 ATtiny44
- 24.3 ATtiny84
25. Packaging Information
- 25.1 20M1
- 25.2 14P3
- 25.3 14S1
26. Errata
- 26.1 ATtiny24
- 26.2 ATtiny44
  - 26.2.1 Rev. B – D
  - 26.2.2 Rev. A
- 26.3 ATtiny84
  - 26.3.1 Rev. A – B
27. Datasheet Revision History
- 27.1 Rev K. - 10/10
- 27.2 Rev J. - 08/10
- 27.3 Rev I. - 06/10
- 27.4 Rev H. 10/09
- 27.5 Rev G. 01/08
- 27.6 Rev F. 02/07
- 27.7 Rev E. 09/06
- 27.8 Rev D. 08/06
- 27.9 Rev C. 07/06
- 27.10 Rev B. 05/06
- 27.11 Rev A. 12/05
Table of Contents

8006K–AVR–10/10

ATtiny24/44/84

The timing diagram for the CTC mode is shown in Figure 11-5 on page 75. The counter value

(TCNT0) increases until a Compare Match occurs between TCNT0 and OCR0A, and then coun-

ter (TCNT0) is cleared.

Figure 11-5. CTC Mode, Timing Diagram

An interrupt can be generated each time the counter value reaches the TOP value by using the

OCF0A Flag. If the interrupt is enabled, the interrupt handler routine can be used for updating

the TOP value. However, changing TOP to a value close to BOTTOM when the counter is run-

ning with none or a low prescaler value must be done with care since the CTC mode does not

have the double buffering feature. If the new value written to OCR0A is lower than the current

value of TCNT0, the counter will miss the Compare Match. The counter will then have to count to

its maximum value (0xFF) and wrap around starting at 0x00 before the Compare Match can

occur.

For generating a waveform output in CTC mode, the OC0A output can be set to toggle its logical

level on each Compare Match by setting the Compare Output mode bits to toggle mode

(COM0A1:0 = 1). The OC0A value will not be visible on the port pin unless the data direction for

the pin is set to output. The waveform generated will have a maximum frequency of

= f

clk_I/O

when OCR0A is set to zero (0x00). The waveform frequency is defined by the following

equation:

The N variable represents the prescale factor (1, 8, 64, 256, or 1024).

As for the Normal mode of operation, the TOV0 Flag is set in the same timer clock cycle that the

counter counts from MAX to 0x00.

11.7.3 Fast PWM Mode

The fast Pulse Width Modulation or fast PWM mode (WGM02:0 = 3 or 7) provides a high fre-

quency PWM waveform generation option. The fast PWM differs from the other PWM option by

its single-slope operation. The counter counts from BOTTOM to TOP then restarts from BOT-

TOM. TOP is defined as 0xFF when WGM2:0 = 3, and OCR0A when WGM2:0 = 7. In non-

inverting Compare Output mode, the Output Compare (OC0x) is cleared on the Compare Match

between TCNT0 and OCR0x, and set at BOTTOM. In inverting Compare Output mode, the out-

put is set on Compare Match and cleared at BOTTOM. Due to the single-slope operation, the

operating frequency of the fast PWM mode can be twice as high as the phase correct PWM

mode that use dual-slope operation. This high frequency makes the fast PWM mode well suited

TCNTn

OCn

(Toggle)

OCnx Interrupt Flag Set

1 4

Period

2 3

(COMnx1:0 = 1)

OCnx

clk_I/O

2 N 1 OCRnx+()⋅⋅

------------------------------------------------- -=