Datasheet
Table Of Contents
- Features
- 1. Pin Configurations
- 2. Overview
- 3. About
- 4. CPU Core
- 5. Memories
- 6. Clock System
- 7. Power Management and Sleep Modes
- 8. System Control and Reset
- 9. Interrupts
- 10. I/O Ports
- 11. 8-bit Timer/Counter0 with PWM
- 11.1 Features
- 11.2 Overview
- 11.3 Clock Sources
- 11.4 Counter Unit
- 11.5 Output Compare Unit
- 11.6 Compare Match Output Unit
- 11.7 Modes of Operation
- 11.8 Timer/Counter Timing Diagrams
- 11.9 Register Description
- 11.9.1 TCCR0A – Timer/Counter Control Register A
- 11.9.2 TCCR0B – Timer/Counter Control Register B
- 11.9.3 TCNT0 – Timer/Counter Register
- 11.9.4 OCR0A – Output Compare Register A
- 11.9.5 OCR0B – Output Compare Register B
- 11.9.6 TIMSK0 – Timer/Counter 0 Interrupt Mask Register
- 11.9.7 TIFR0 – Timer/Counter 0 Interrupt Flag Register
- 12. 16-bit Timer/Counter1
- 12.1 Features
- 12.2 Overview
- 12.3 Timer/Counter Clock Sources
- 12.4 Counter Unit
- 12.5 Input Capture Unit
- 12.6 Output Compare Units
- 12.7 Compare Match Output Unit
- 12.8 Modes of Operation
- 12.9 Timer/Counter Timing Diagrams
- 12.10 Accessing 16-bit Registers
- 12.11 Register Description
- 12.11.1 TCCR1A – Timer/Counter1 Control Register A
- 12.11.2 TCCR1B – Timer/Counter1 Control Register B
- 12.11.3 TCCR1C – Timer/Counter1 Control Register C
- 12.11.4 TCNT1H and TCNT1L – Timer/Counter1
- 12.11.5 OCR1AH and OCR1AL – Output Compare Register 1 A
- 12.11.6 OCR1BH and OCR1BL – Output Compare Register 1 B
- 12.11.7 ICR1H and ICR1L – Input Capture Register 1
- 12.11.8 TIMSK1 – Timer/Counter Interrupt Mask Register 1
- 12.11.9 TIFR1 – Timer/Counter Interrupt Flag Register 1
- 13. Timer/Counter Prescaler
- 14. USI – Universal Serial Interface
- 15. Analog Comparator
- 16. Analog to Digital Converter
- 16.1 Features
- 16.2 Overview
- 16.3 Operation
- 16.4 Starting a Conversion
- 16.5 Prescaling and Conversion Timing
- 16.6 Changing Channel or Reference Selection
- 16.7 ADC Noise Canceler
- 16.8 Analog Input Circuitry
- 16.9 Noise Canceling Techniques
- 16.10 ADC Accuracy Definitions
- 16.11 ADC Conversion Result
- 16.12 Temperature Measurement
- 16.13 Register Description
- 17. debugWIRE On-chip Debug System
- 18. Self-Programming the Flash
- 18.1 Performing Page Erase by SPM
- 18.2 Filling the Temporary Buffer (Page Loading)
- 18.3 Performing a Page Write
- 18.4 Addressing the Flash During Self-Programming
- 18.5 EEPROM Write Prevents Writing to SPMCSR
- 18.6 Reading Lock, Fuse and Signature Data from Software
- 18.7 Preventing Flash Corruption
- 18.8 Programming Time for Flash when Using SPM
- 18.9 Register Description
- 19. Memory Programming
- 19.1 Program And Data Memory Lock Bits
- 19.2 Fuse Bytes
- 19.3 Device Signature Imprint Table
- 19.4 Page Size
- 19.5 Serial Programming
- 19.6 High-voltage Serial Programming
- 19.7 High-Voltage Serial Programming Algorithm
- 19.7.1 Enter High-voltage Serial Programming Mode
- 19.7.2 Considerations for Efficient Programming
- 19.7.3 Chip Erase
- 19.7.4 Programming the Flash
- 19.7.5 Programming the EEPROM
- 19.7.6 Reading the Flash
- 19.7.7 Reading the EEPROM
- 19.7.8 Programming and Reading the Fuse and Lock Bits
- 19.7.9 Reading the Signature Bytes and Calibration Byte
- 19.7.10 Power-off sequence
- 20. Electrical Characteristics
- 21. Typical Characteristics
- 21.1 Supply Current of I/O Modules
- 21.2 Active Supply Current
- 21.3 Idle Supply Current
- 21.4 Power-down Supply Current
- 21.5 Standby Supply Current
- 21.6 Pin Pull-up
- 21.7 Pin Driver Strength
- 21.8 Pin Threshold and Hysteresis
- 21.9 BOD Threshold and Analog Comparator Offset
- 21.10 Internal Oscillator Speed
- 21.11 Current Consumption of Peripheral Units
- 21.12 Current Consumption in Reset and Reset Pulsewidth
- 22. Register Summary
- 23. Instruction Set Summary
- 24. Ordering Information
- 25. Packaging Information
- 26. Errata
- 27. Datasheet Revision History
- Table of Contents
61
8006K–AVR–10/10
ATtiny24/44/84
10.2.1 Alternate Functions of Port A
The Port A pins with alternate function are shown in Table 10-3.
• Port A, Bit 0 – ADC0/AREF/PCINT0
• ADC0: Analog to Digital Converter, Channel 0
.
• AREF: External Analog Reference for ADC. Pullup and output driver are disabled on PA0
when the pin is used as an external reference or Internal Voltage Reference with external
capacitor at the AREF pin by setting (one) the bit REFS0 in the ADC Multiplexer Selection
Register (ADMUX).
• PCINT0: Pin Change Interrupt source 0. The PA0 pin can serve as an external interrupt
source for pin change interrupt 0.
Table 10-3. Port A Pins Alternate Functions
Port Pin Alternate Function
PA0
ADC0: ADC Input Channel 0
AREF: External Analog Reference
PCINT0: Pin Change Interrupt 0, Source 0
PA1
ADC1: ADC Input Channel 1
AIN0: Analog Comparator, Positive Input
PCINT1:Pin Change Interrupt 0, Source 1
PA2
ADC2: ADC Input Channel 2
AIN1: Analog Comparator, Negative Input
PCINT2: Pin Change Interrupt 0, Source 2
PA3
ADC3: ADC Input Channel 3
T0: Timer/Counter0 Clock Source.
PCINT3: Pin Change Interrupt 0, Source 3
PA4
ADC4: ADC Input Channel 4
USCK: USI Clock (Three Wire Mode)
SCL : USI Clock (Two Wire Mode)
T1: Timer/Counter1 Clock Source
PCINT4: Pin Change Interrupt 0, Source 4
PA5
ADC5: ADC Input Channel 5
DO: USI Data Output (Three Wire Mode)
MISO: SPI Master Data Input / Slave Data Output
OC1B: Timer/Counter1 Compare Match B Output
PCINT5: Pin Change Interrupt 0, Source 5
PA6
ADC6: ADC Input Channel 6
DI: USI Data Input (Three Wire Mode)
SDA: USI Data Input (Two Wire Mode)
MOSI: SPI Master Data Output / Slave Data Input
OC1A: Timer/Counter1 Compare Match A Output
PCINT6: Pin Change Interrupt 0, Source 6
PA7
ADC7: ADC Input Channel 7
OC0B: Timer/Counter0 Compare Match B Output
ICP1: Timer/Counter1 Input Capture Pin
PCINT7: Pin Change Interrupt 0, Source 7