Datasheet

ManualsBrandsMICROCHIP TECHNOLOGY ManualsMicrocontrollers, Microprocessors & QuartzesEmbedded microcontroller QFN 20 (4x4) 8-Bit 20 MHz I/O number 12

171

172

173

174

175

176

177

178

179

180

Table Of Contents

Features
1. Pin Configurations
- 1.1 Pin Descriptions
2. Overview
3. About
- 3.1 Resources
- 3.2 Code Examples
- 3.3 Data Retention
- 3.4 Disclaimer
4. CPU Core
- 4.1 Architectural Overview
- 4.2 ALU – Arithmetic Logic Unit
- 4.3 Status Register
  - 4.3.1 SREG – AVR Status Register
- 4.4 General Purpose Register File
  - 4.4.1 The X-register, Y-register, and Z-register
- 4.5 Stack Pointer
  - 4.5.1 SPH and SPL — Stack Pointer Register
- 4.6 Instruction Execution Timing
- 4.7 Reset and Interrupt Handling
  - 4.7.1 Interrupt Response Time
5. Memories
- 5.1 In-System Re-programmable Flash Program Memory
- 5.2 SRAM Data Memory
  - 5.2.1 Data Memory Access Times
- 5.3 EEPROM Data Memory
- 5.4 I/O Memory
  - 5.4.1 General Purpose I/O Registers
- 5.5 Register Description
6. Clock System
- 6.1 Clock Subsystems
- 6.2 Clock Sources
- 6.3 System Clock Prescaler
  - 6.3.1 Switching Time
- 6.4 Clock Output Buffer
- 6.5 Register Description
  - 6.5.1 OSCCAL – Oscillator Calibration Register
  - 6.5.2 CLKPR – Clock Prescale Register
7. Power Management and Sleep Modes
- 7.1 Sleep Modes
- 7.2 Software BOD Disable
  - 7.2.1 Limitations
- 7.3 Power Reduction Register
- 7.4 Minimizing Power Consumption
- 7.5 Register Description
  - 7.5.1 MCUCR – MCU Control Register
  - 7.5.2 PRR – Power Reduction Register
8. System Control and Reset
- 8.1 Resetting the AVR
- 8.2 Reset Sources
- 8.3 Internal Voltage Reference
  - 8.3.1 Voltage Reference Enable Signals and Start-up Time
- 8.4 Watchdog Timer
  - 8.4.1 Timed Sequences for Changing the Configuration of the Watchdog Timer
    - 8.4.1.1 Safety Level 1
    - 8.4.1.2 Safety Level 2
  - 8.4.2 Code Example
- 8.5 Register Description
  - 8.5.1 MCUSR – MCU Status Register
  - 8.5.2 WDTCSR – Watchdog Timer Control and Status Register
9. Interrupts
- 9.1 Interrupt Vectors
- 9.2 External Interrupts
  - 9.2.1 Low Level Interrupt
  - 9.2.2 Pin Change Interrupt Timing
- 9.3 Register Description
10. I/O Ports
- 10.1 Ports as General Digital I/O
- 10.2 Alternate Port Functions
  - 10.2.1 Alternate Functions of Port A
  - 10.2.2 Alternate Functions of Port B
- 10.3 Register Description
11. 8-bit Timer/Counter0 with PWM
- 11.1 Features
- 11.2 Overview
  - 11.2.1 Registers
  - 11.2.2 Definitions
- 11.3 Clock Sources
- 11.4 Counter Unit
- 11.5 Output Compare Unit
- 11.6 Compare Match Output Unit
  - 11.6.1 Compare Output Mode and Waveform Generation
- 11.7 Modes of Operation
- 11.8 Timer/Counter Timing Diagrams
- 11.9 Register Description
12. 16-bit Timer/Counter1
- 12.1 Features
- 12.2 Overview
- 12.3 Timer/Counter Clock Sources
- 12.4 Counter Unit
- 12.5 Input Capture Unit
- 12.6 Output Compare Units
- 12.7 Compare Match Output Unit
  - 12.7.1 Compare Output Mode and Waveform Generation
- 12.8 Modes of Operation
- 12.9 Timer/Counter Timing Diagrams
- 12.10 Accessing 16-bit Registers
  - 12.10.1 Reusing the Temporary High Byte Register
- 12.11 Register Description
13. Timer/Counter Prescaler
- 13.1 Prescaler Reset
- 13.2 External Clock Source
- 13.3 Register Description
  - 13.3.1 GTCCR – General Timer/Counter Control Register
14. USI – Universal Serial Interface
- 14.1 Features
- 14.2 Overview
- 14.3 Functional Descriptions
- 14.4 Alternative USI Usage
- 14.5 Register Descriptions
15. Analog Comparator
- 15.1 Analog Comparator Multiplexed Input
- 15.2 Register Description
16. Analog to Digital Converter
- 16.1 Features
- 16.2 Overview
- 16.3 Operation
- 16.4 Starting a Conversion
- 16.5 Prescaling and Conversion Timing
- 16.6 Changing Channel or Reference Selection
  - 16.6.1 ADC Input Channels
  - 16.6.2 ADC Voltage Reference
- 16.7 ADC Noise Canceler
- 16.8 Analog Input Circuitry
- 16.9 Noise Canceling Techniques
- 16.10 ADC Accuracy Definitions
- 16.11 ADC Conversion Result
- 16.12 Temperature Measurement
- 16.13 Register Description
17. debugWIRE On-chip Debug System
- 17.1 Features
- 17.2 Overview
- 17.3 Physical Interface
- 17.4 Software Break Points
- 17.5 Limitations of debugWIRE
- 17.6 Register Description
  - 17.6.1 DWDR – debugWire Data Register
18. Self-Programming the Flash
- 18.1 Performing Page Erase by SPM
- 18.2 Filling the Temporary Buffer (Page Loading)
- 18.3 Performing a Page Write
- 18.4 Addressing the Flash During Self-Programming
- 18.5 EEPROM Write Prevents Writing to SPMCSR
- 18.6 Reading Lock, Fuse and Signature Data from Software
- 18.7 Preventing Flash Corruption
- 18.8 Programming Time for Flash when Using SPM
- 18.9 Register Description
  - 18.9.1 SPMCSR – Store Program Memory Control and Status Register
19. Memory Programming
- 19.1 Program And Data Memory Lock Bits
- 19.2 Fuse Bytes
  - 19.2.1 Latching of Fuses
- 19.3 Device Signature Imprint Table
  - 19.3.1 Signature Bytes
  - 19.3.2 Calibration Byte
- 19.4 Page Size
- 19.5 Serial Programming
  - 19.5.1 Serial Programming Algorithm
  - 19.5.2 Serial Programming Instruction set
- 19.6 High-voltage Serial Programming
- 19.7 High-Voltage Serial Programming Algorithm
20. Electrical Characteristics
- 20.1 Absolute Maximum Ratings*
- 20.2 DC Characteristics
- 20.3 Speed
- 20.4 Clock Characteristics
  - 20.4.1 Accuracy of Calibrated Internal RC Oscillator
  - 20.4.2 External Clock Drive
- 20.5 System and Reset Characteristics
- 20.6 Analog Comparator Characteristics
- 20.7 ADC Characteristics
- 20.8 Serial Programming Characteristics
- 20.9 High-Voltage Serial Programming Characteristics
21. Typical Characteristics
- 21.1 Supply Current of I/O Modules
  - 21.1.1 Example
- 21.2 Active Supply Current
- 21.3 Idle Supply Current
- 21.4 Power-down Supply Current
- 21.5 Standby Supply Current
- 21.6 Pin Pull-up
- 21.7 Pin Driver Strength
- 21.8 Pin Threshold and Hysteresis
- 21.9 BOD Threshold and Analog Comparator Offset
- 21.10 Internal Oscillator Speed
- 21.11 Current Consumption of Peripheral Units
- 21.12 Current Consumption in Reset and Reset Pulsewidth
22. Register Summary
23. Instruction Set Summary
24. Ordering Information
- 24.1 ATtiny24
- 24.2 ATtiny44
- 24.3 ATtiny84
25. Packaging Information
- 25.1 20M1
- 25.2 14P3
- 25.3 14S1
26. Errata
- 26.1 ATtiny24
- 26.2 ATtiny44
  - 26.2.1 Rev. B – D
  - 26.2.2 Rev. A
- 26.3 ATtiny84
  - 26.3.1 Rev. A – B
27. Datasheet Revision History
- 27.1 Rev K. - 10/10
- 27.2 Rev J. - 08/10
- 27.3 Rev I. - 06/10
- 27.4 Rev H. 10/09
- 27.5 Rev G. 01/08
- 27.6 Rev F. 02/07
- 27.7 Rev E. 09/06
- 27.8 Rev D. 08/06
- 27.9 Rev C. 07/06
- 27.10 Rev B. 05/06
- 27.11 Rev A. 12/05
Table of Contents

180

8006K–AVR–10/10

ATtiny24/44/84

20.7 ADC Characteristics

Note: 1. Values are guidelines only.

Table 20-9. ADC Characteristics, Single Ended Channels. T = -40°C to +85°C

Symbol Parameter Condition Min

(1)

Typ

(1)

Max

(1)

Units

Resolution 10 Bits

Absolute accuracy

(Including INL, DNL, and

Quantization, Gain and Offset

Errors)

REF

= 4V, V

= 4V,

ADC clock = 200 kHz

2.0 LSB

REF

= 4V, V

= 4V,

ADC clock = 1 MHz

2.5 LSB

REF

= 4V, V

= 4V,

ADC clock = 200 kHz

Noise Reduction Mode

1.5 LSB

REF

= 4V, V

= 4V,

ADC clock = 1 MHz

Noise Reduction Mode

2.0 LSB

Integral Non-Linearity (INL)

(Accuracy after Offset and

Gain Calibration)

REF

= 4V, V

= 4V,

ADC clock = 200 kHz

1.0 LSB

Differential Non-linearity

(DNL)

REF

= 4V, V

= 4V,

ADC clock = 200 kHz

0.5 LSB

Gain Error

REF

= 4V, V

= 4V,

ADC clock = 200 kHz

2.0 LSB

Offset Error

REF

= 4V, V

= 4V,

ADC clock = 200 kHz

1.5 LSB

Conversion Time Free Running Conversion 14 280 µs

Clock Frequency 50 1000 kHz

Input Voltage GND V

REF

Input Bandwidth 38.4 kHz

REF

External Voltage Reference 2.0 V

INT

Internal Voltage Reference 1.0 1.1 1.2 V

REF

Reference Input Resistance 32 kΩ

AIN

Analog Input Resistance 100 MΩ

ADC Conversion Output 0 1023 LSB