Datasheet
Table Of Contents
- Features
- 1. Pin Configurations
- 2. Overview
- 3. About
- 4. CPU Core
- 5. Memories
- 6. Clock System
- 7. Power Management and Sleep Modes
- 8. System Control and Reset
- 9. Interrupts
- 10. I/O Ports
- 11. 8-bit Timer/Counter0 with PWM
- 11.1 Features
- 11.2 Overview
- 11.3 Clock Sources
- 11.4 Counter Unit
- 11.5 Output Compare Unit
- 11.6 Compare Match Output Unit
- 11.7 Modes of Operation
- 11.8 Timer/Counter Timing Diagrams
- 11.9 Register Description
- 11.9.1 TCCR0A – Timer/Counter Control Register A
- 11.9.2 TCCR0B – Timer/Counter Control Register B
- 11.9.3 TCNT0 – Timer/Counter Register
- 11.9.4 OCR0A – Output Compare Register A
- 11.9.5 OCR0B – Output Compare Register B
- 11.9.6 TIMSK0 – Timer/Counter 0 Interrupt Mask Register
- 11.9.7 TIFR0 – Timer/Counter 0 Interrupt Flag Register
- 12. 16-bit Timer/Counter1
- 12.1 Features
- 12.2 Overview
- 12.3 Timer/Counter Clock Sources
- 12.4 Counter Unit
- 12.5 Input Capture Unit
- 12.6 Output Compare Units
- 12.7 Compare Match Output Unit
- 12.8 Modes of Operation
- 12.9 Timer/Counter Timing Diagrams
- 12.10 Accessing 16-bit Registers
- 12.11 Register Description
- 12.11.1 TCCR1A – Timer/Counter1 Control Register A
- 12.11.2 TCCR1B – Timer/Counter1 Control Register B
- 12.11.3 TCCR1C – Timer/Counter1 Control Register C
- 12.11.4 TCNT1H and TCNT1L – Timer/Counter1
- 12.11.5 OCR1AH and OCR1AL – Output Compare Register 1 A
- 12.11.6 OCR1BH and OCR1BL – Output Compare Register 1 B
- 12.11.7 ICR1H and ICR1L – Input Capture Register 1
- 12.11.8 TIMSK1 – Timer/Counter Interrupt Mask Register 1
- 12.11.9 TIFR1 – Timer/Counter Interrupt Flag Register 1
- 13. Timer/Counter Prescaler
- 14. USI – Universal Serial Interface
- 15. Analog Comparator
- 16. Analog to Digital Converter
- 16.1 Features
- 16.2 Overview
- 16.3 Operation
- 16.4 Starting a Conversion
- 16.5 Prescaling and Conversion Timing
- 16.6 Changing Channel or Reference Selection
- 16.7 ADC Noise Canceler
- 16.8 Analog Input Circuitry
- 16.9 Noise Canceling Techniques
- 16.10 ADC Accuracy Definitions
- 16.11 ADC Conversion Result
- 16.12 Temperature Measurement
- 16.13 Register Description
- 17. debugWIRE On-chip Debug System
- 18. Self-Programming the Flash
- 18.1 Performing Page Erase by SPM
- 18.2 Filling the Temporary Buffer (Page Loading)
- 18.3 Performing a Page Write
- 18.4 Addressing the Flash During Self-Programming
- 18.5 EEPROM Write Prevents Writing to SPMCSR
- 18.6 Reading Lock, Fuse and Signature Data from Software
- 18.7 Preventing Flash Corruption
- 18.8 Programming Time for Flash when Using SPM
- 18.9 Register Description
- 19. Memory Programming
- 19.1 Program And Data Memory Lock Bits
- 19.2 Fuse Bytes
- 19.3 Device Signature Imprint Table
- 19.4 Page Size
- 19.5 Serial Programming
- 19.6 High-voltage Serial Programming
- 19.7 High-Voltage Serial Programming Algorithm
- 19.7.1 Enter High-voltage Serial Programming Mode
- 19.7.2 Considerations for Efficient Programming
- 19.7.3 Chip Erase
- 19.7.4 Programming the Flash
- 19.7.5 Programming the EEPROM
- 19.7.6 Reading the Flash
- 19.7.7 Reading the EEPROM
- 19.7.8 Programming and Reading the Fuse and Lock Bits
- 19.7.9 Reading the Signature Bytes and Calibration Byte
- 19.7.10 Power-off sequence
- 20. Electrical Characteristics
- 21. Typical Characteristics
- 21.1 Supply Current of I/O Modules
- 21.2 Active Supply Current
- 21.3 Idle Supply Current
- 21.4 Power-down Supply Current
- 21.5 Standby Supply Current
- 21.6 Pin Pull-up
- 21.7 Pin Driver Strength
- 21.8 Pin Threshold and Hysteresis
- 21.9 BOD Threshold and Analog Comparator Offset
- 21.10 Internal Oscillator Speed
- 21.11 Current Consumption of Peripheral Units
- 21.12 Current Consumption in Reset and Reset Pulsewidth
- 22. Register Summary
- 23. Instruction Set Summary
- 24. Ordering Information
- 25. Packaging Information
- 26. Errata
- 27. Datasheet Revision History
- Table of Contents
129
8006K–AVR–10/10
ATtiny24/44/84
15. Analog Comparator
The analog comparator compares the input values on the positive pin AIN0 and negative pin
AIN1. When the voltage on the positive pin AIN0 is higher than the voltage on the negative pin
AIN1, the Analog Comparator Output, ACO, is set. The comparator can trigger a separate inter-
rupt, exclusive to the Analog Comparator. The user can select Interrupt triggering on comparator
output rise, fall or toggle. A block diagram of the comparator and its surrounding logic is shown
in Figure 15-1.
Figure 15-1. Analog Comparator Block Diagram
Notes: 1. See Table 15-1 on page 129.
See Figure 1-1 on page 2 and Table 10-9 on page 67 for Analog Comparator pin placement.
15.1 Analog Comparator Multiplexed Input
When the Analog to Digital Converter (ADC) is configurated as single ended input channel, it is
possible to select any of the ADC7:0 pins to replace the negative input to the Analog Compara-
tor. The ADC multiplexer is used to select this input, and consequently, the ADC must be
switched off to utilize this feature. If the Analog Comparator Multiplexer Enable bit (ACME in
ADCSRB) is set and the ADC is switched off (ADEN in ADCSRA is zero), MUX1:0 in ADMUX
select the input pin to replace the negative input to the analog comparator, as shown in Table
15-1. If ACME is cleared or ADEN is set, AIN1 is applied to the negative input to the analog
comparator.
ACBG
BANDGAP
REFERENCE
ADC MULTIPLEXER
OUTPUT
ACME
ADEN
(1)
ACIC
To T/C1 Capture
Trigger MUX
Table 15-1. Analog Comparator Multiplexed Input
ACME ADEN MUX4:0 Analog Comparator Negative Input
0 X XXXXX AIN1
1 1 XXXXX AIN1
1 0 00000 ADC0
1 0 00001 ADC1
1 0 00010 ADC2
1 0 00011 ADC3