Datasheet

119
ATtiny13
2535E–AVR–10/04
Electrical Characteristics
Absolute Maximum Ratings*
DC Characteristics
Operating Temperature.................................. -55°C to +125°C
*NOTICE: Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
Storage Temperature ..................................... -65°C to +150°C
Voltage on any Pin except RESET
with respect to Ground ................................-0.5V to V
CC
+0.5V
Voltage on RESET
with respect to Ground......-0.5V to +13.0V
Maximum Operating Voltage ............................................ 6.0V
DC Current per I/O Pin ............................................... 40.0 mA
DC Current
V
CC
and GND Pins................................ 200.0 mA
T
A
= -40°C to 85°C, V
CC
= 1.8V to 5.5V (unless otherwise noted)
(1)
Symbol Parameter Condition Min. Typ. Max. Units
V
IL
Input Low Voltage -0.5 0.2V
CC
V
V
IH
Input High-voltage Except RESET pin 0.6V
CC
(3)
V
CC
+0.5 V
V
IH2
Input High-voltage RESET pin 0.9V
CC
(3)
V
CC
+0.5 V
V
OL
Output Low Voltage
(4)
(PB5, PB1 and PB0)
I
OL
= 20 mA, V
CC
= 5V
I
OL
= 10 mA, V
CC
= 3V
0.7
0.5
V
V
V
OL1
Output Low Voltage
(4)
(PB4, PB3 and PB2)
I
OL
= 10 mA, V
CC
= 5V
I
OL
= 5 mA, V
CC
= 3V
0.7
0.5
V
V
V
OH
Output High-voltage
(5)
(PB5, PB1 and PB0)
I
OH
= -20 mA, V
CC
= 5V
I
OH
= -10 mA, V
CC
= 3V
4.2
2.5
V
V
V
OH1
Output High-voltage
(5)
(PB4, PB3 and PB2)
I
OH
= -10 mA, V
CC
= 5V
I
OH
= -5 mA, V
CC
= 3V
4.2
2.5
V
V
I
IL
Input Leakage
Current I/O Pin
Vcc = 5.5V, p i n l ow
(absolute value)
1µA
I
IH
Input Leakage
Current I/O Pin
Vcc = 5.5V, pin high
(absolute value)
1µA
R
RST
Reset Pull-up Resistor 30 80 kΩ
R
pu
I/O Pin Pull-up Resistor 20 50 kΩ
I
CC
Power Supply Current
Active 1MHz, V
CC
= 2V 0.35 mA
Active 4MHz, V
CC
= 3V 1.8 mA
Active 8MHz, V
CC
= 5V 6 mA
Idle 1MHz, V
CC
= 2V 0.08 0.2 mA
Idle 4MHz, V
CC
= 3V 0.41 1 mA
Idle 8MHz, V
CC
= 5V 1.6 3 mA
Power-down mode
WDT enabled, V
CC
= 3V < 5 5 µA
WDT disabled, V
CC
= 3V < 0.5 2 µA