Datasheet
Table Of Contents
- Features
- Pin Configuration
- Description
- Architectural Overview
- General-purpose Register File
- ALU – Arithmetic Logic Unit
- Flash Program Memory
- Program and Data Addressing Modes
- Subroutine and Interrupt Hardware Stack
- EEPROM Data Memory
- Memory Access and Instruction Execution Timing
- I/O Memory
- Reset and Interrupt Handling
- ATtiny12 Internal Voltage Reference
- Interrupt Handling
- Sleep Modes for the ATtiny11
- Sleep Modes for the ATtiny12
- ATtiny12 Calibrated Internal RC Oscillator
- Timer/Counter0
- Watchdog Timer
- ATtiny12 EEPROM Read/Write Access
- Analog Comparator
- I/O Port B
- Memory Programming
- Program (and Data) Memory Lock Bits
- Fuse Bits in ATtiny11
- Fuse Bits in ATtiny12
- Signature Bytes
- Calibration Byte in ATtiny12
- Programming the Flash and EEPROM
- High-voltage Serial Programming
- High-voltage Serial Programming Algorithm
- High-voltage Serial Programming Characteristics
- Low-voltage Serial Downloading (ATtiny12 only)
- Low-voltage Serial Programming Characteristics
- Electrical Characteristics
- Register Summary ATtiny11
- Register Summary ATtiny12
- Instruction Set Summary
- Ordering Information
- Packaging Information
- Data Sheet Change Log for ATtiny11/12
- Table of Contents
50
ATtiny11/12
1006D–AVR–07/03
Figure 28. High-voltage Serial Programming Waveforms
MSB
MSB
MSB LSB
LSB
LSB
012345678910
SERIAL DATA INPUT
PB0
SERIAL INSTR. INPUT
PB1
SERIAL DATA OUTPUT
PB2
SERIAL CLOCK INPUT
XTAL1/PB3
Table 23. High-voltage Serial Programming Instruction Set for ATtiny11/12
Instruction
Instruction Format
Operation RemarksInstr.1 Instr.2 Instr.3 Instr.4
Chip Erase
PB0
PB1
PB2
0_1000_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
Wait after Instr.4 until PB2 goes
high for the Chip Erase cycle to
finish.
Write Flash
High and Low
Address
PB0
PB1
PB2
0_0001_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_0000_000a_00
0_0001_1100_00
x_xxxx_xxxx_xx
0_bbbb_bbbb_00
0_0000_1100_00
x_xxxx_xxxx_xx
Repeat Instr.2 for a new 256 byte
page. Repeat Instr.3 for each new
address.
Write Flash Low
byte
PB0
PB1
PB2
0_ i i i i_i i i i _00
0_0010_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
0_0000_0000_00
Wait after Instr.3 until PB2 goes
high. Repeat Instr.1, Instr. 2 and
Instr.3 for each new address.
Write Flash
High byte
PB0
PB1
PB2
0_ i i i i_i i i i _00
0_0011_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_0100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1100_00
0_0000_0000_00
Wait after Instr.3 until PB2 goes
high. Repeat Instr.1, Instr. 2 and
Instr.3 for each new address.
Read Flash
High and Low
Address
PB0
PB1
PB2
0_0000_0010_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_0000_000a_00
0_0001_1100_00
x_xxxx_xxxx_xx
0_bbbb_bbbb_00
0_0000_1100_00
x_xxxx_xxxx_xx
Repeat Instr.2 and Instr.3 for each
new address.
Read Flash
Low byte
PB0
PB1
PB2
0_0000_0000_00
0_0110_1000_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
o_oooo_ooox_xx
Repeat Instr.1 and Instr.2 for each
new address.
Read Flash
High byte
PB0
PB1
PB2
0_0000_0000_00
0_0111_1000_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1100_00
o_oooo_ooox_xx
Repeat Instr.1 and Instr.2 for each
new address.
Write EEPROM
Low Address
(ATtiny12)
PB0
PB1
PB2
0_0001_0001_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_00bb_bbbb_00
0_0000_1100_00
x_xxxx_xxxx_xx
Repeat Instr.2 for each new
address.
Write EEPROM
byte (ATtiny12)
PB0
PB1
PB2
0_ i i i i_i i i i _00
0_0010_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
0_0000_0000_00
Wait after Instr.3 until PB2 goes
high
Read EEPROM
Low Address
(ATtiny12)
PB0
PB1
PB2
0_0000_0011_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_00bb_bbbb_00
0_0000_1100_00
x_xxxx_xxxx_xx
Repeat Instr.2 for each new
address.