Datasheet

ATmega48/88/168 Automotive [DATASHEET]
7530K–AVR–07/14
162
• Bit 3 – DORn: Data OverRun
This bit is set if a data overrun condition is detected. A data overrun occurs when the receive buffer is full (two characters), it
is a new character waiting in the receive shift register, and a new start bit is detected. This bit is valid until the receive buffer
(UDRn) is read. Always set this bit to zero when writing to UCSRnA.
• Bit 2 – UPEn: USART Parity Error
This bit is set if the next character in the receive buffer had a parity error when received and the parity checking was enabled
at that point (UPMn1 = 1). This bit is valid until the receive buffer (UDRn) is read. Always set this bit to zero when writing to
UCSRnA.
• Bit 1 – U2Xn: Double the USART Transmission Speed
This bit only has effect for the asynchronous operation. Write this bit to zero when using synchronous operation.
Writing this bit to one will reduce the divisor of the baud rate divider from 16 to 8 effectively doubling the transfer rate for
asynchronous communication.
• Bit 0 – MPCMn: Multi-processor Communication Mode
This bit enables the multi-processor communication mode. When the MPCMn bit is written to one, all the incoming frames
received by the USART receiver that do not contain address information will be ignored. The transmitter is unaffected by the
MPCMn setting. For more detailed information see Section 17.8 “Multi-processor Communication Mode” on page 160.
17.9.3 USART Control and Status Register n B – UCSRnB
• Bit 7 – RXCIEn: RX Complete Interrupt Enable n
Writing this bit to one enables interrupt on the RXCn flag. A USART receive complete interrupt will be generated only if the
RXCIEn bit is written to one, the global interrupt flag in SREG is written to one and the RXCn bit in UCSRnA is set.
• Bit 6 – TXCIEn: TX Complete Interrupt Enable n
Writing this bit to one enables interrupt on the TXCn flag. A USART transmit complete interrupt will be generated only if the
TXCIEn bit is written to one, the global interrupt flag in SREG is written to one and the TXCn bit in UCSRnA is set.
• Bit 5 – UDRIEn: USART Data Register Empty Interrupt Enable n
Writing this bit to one enables interrupt on the UDREn flag. A data register empty interrupt will be generated only if the
UDRIEn bit is written to one, the global interrupt flag in SREG is written to one and the UDREn bit in UCSRnA is set.
• Bit 4 – RXENn: Receiver Enable n
Writing this bit to one enables the USART receiver. The receiver will override normal port operation for the RxDn pin when
enabled. Disabling the receiver will flush the receive buffer invalidating the FEn, DORn, and UPEn flags.
• Bit 3 – TXENn: Transmitter Enable n
Writing this bit to one enables the USART transmitter. The transmitter will override normal port operation for the TxDn pin
when enabled. The disabling of the transmitter (writing TXENn to zero) will not become effective until ongoing and pending
transmissions are completed, i.e., when the transmit shift register and transmit buffer register do not contain data to be
transmitted. When disabled, the transmitter will no longer override the TxDn port.
Bit 76543210
RXCIEn TXCIEn UDRIEn RXENn TXENn UCSZn2 RXB8n TXB8n UCSRnB
Read/Write R/W R/W R/W R/W R/W R/W R R/W
Initial Value 0 0 0 0 0 0 0 0