Atmel ATmega16M1/32M1/32C1/64M1/64C1 Automotive Appendix A - Atmel ATmega16M1/ATmega32M1/ ATmega32C1/ATmega64M1/ATmega64C1 Automotive Specification at 150°C DATASHEET Description This document contains information specific to devices operating at temperatures up to 150°C. Only deviations are covered in this appendix, all other information can be found in the complete Automotive datasheet. The complete Automotive datasheet can be found on www.atmel.
1. Electrical Characteristics 1.1 Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
1.2 DC Characteristics (Continued) TA = –40°C to +150°C, VCC = 4.5V to 5.5V (unless otherwise noted) Parameters Test Conditions Output Low Voltage(3), I/O pin except RESET Symbol IOL = 10mA, VCC = 5V VOL Output High Voltage(4), I/O pin except RESET IOH = –10mA, VCC = 5V VOH 4.1 V Output High Voltage (Reset pin) IOH = 0.6mA, VCC = 5V VOH3 3 V Input Leakage Current I/O Pin VCC = 5.5V, pin low (absolute value) IIL 1 µA Input Leakage Current I/O Pin VCC = 5.
1.3 ADC Characteristics in Single-ended Mode TA = –40°C to +150°C, VCC = 4.5V to 5.5V (unless otherwise noted) Parameters Test Conditions Resolution Single ended, Temp = –40°C to 150°C 10 VCC = 5V, VRef = 2.56V, ADC clock = 1MHz 3.2 6.0 3.2 6.0 0.7 3.0 0.8 3.0 0.5 1.5 0.6 1.5 Absolute accuracy Integral Non Linearity Differential Non Linearity Gain error Offset error VCC = 5V, VRef = 2.56V, ADC clock = 2MHz VCC = 5V, VRef = 2.56V, ADC clock = 1MHz VCC = 5V, VRef = 2.
1.4 ADC Characteristics in Differential Mode (Continued) TA = –40°C to +150°C, VCC = 4.5V to 5.5V (unless otherwise noted) Parameters Test Conditions Symbol Min Typ Max 1.5 3.5 1.5 4.0 Gain = 40x, VCC = 5V, VRef = 2.56V, ADC clock = 2MHz 1.5 6.0 Gain = 5x, 10x, VCC = 5V, VRef = 2.56V, ADC clock = 2MHz 0.1 1.5 0.2 2.5 Gain = 40x, VCC = 5V, VRef = 2.56V, ADC clock = 2MHz 0.7 4.5 Gain = 5x, 10x, VCC = 5V, VRef = 2.56V, ADC clock = 2MHz 0.1 1.5 0.2 2.0 0.3 4.
Grade 0 Qualification The ATmega16M1/ATmega32M1/ATmega32C1/ATmega64M1/ATmega64C1 has been developed and manufactured according to the most stringent quality assurance requirements of ISO-TS-16949 and verified during product qualification as per AEC-Q100 grade 0. AEC-Q100 qualification relies on temperature accelerated stress testing. High temperature field usage however may result in less significant stress test acceleration.
3. Ordering Information Table 3-1. ATmega16/32/64/M1/C1 Ordering Code Speed is 16MHz and Power Supply is 4.5V to 5.5V for all devices. Operating range is the same for all devices too Extended (–40°C to +150°C). Speed (MHz) Power Supply Ordering Code Package(1) Operation Range 16(2) 4.5V to 5.5V ATmega16M1-15MD PV Extended (–40°C to +150°C) 16(2) 4.5V to 5.5V ATmega16M1-15AD MA Extended (–40°C to +150°C) 16(2) 4.5V to 5.5V ATmega32M1-ESMD PV Engineering samples (2) 4.5V to 5.
4. Package Information Table 4-1. Package Types Package Type PV 32-lead, 7.0mm × 7.0mm Body, 0.65mm Pitch, Quad Flat No Lead Package (QFN) MA MA, 32 - Lead, 7mm × 7mm Body Size, 1.0mm Body Thickness 0.
Figure 4-1.
Figure 4-2.
5. Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. History 7781E-AVR-03/12 • Package MA updated 7781D-AVR-01/10 • Section 1.
Atmel Corporation 2325 Orchard Parkway Atmel Asia Limited Unit 01-5 & 16, 19F Atmel Munich GmbH Business Campus Atmel Japan G.K. 16F Shin-Osaki Kangyo Building San Jose, CA 95131 BEA Tower, Millennium City 5 Parkring 4 1-6-4 Osaki USA 418 Kwun Tong Roa D-85748 Garching b. Munich Shinagawa-ku, Tokyo 141-0032 Tel: (+1) (408) 441-0311 Kwun Tong, Kowloon GERMANY JAPAN Fax: (+1) (408) 487-2600 HONG KONG Tel: (+49) 89-31970-0 Tel: (+81) (3) 6417-0300 www.atmel.
