Datasheet

340
ATmega169A/PA/329A/PA/649A/P/3290A/PA/6490A/P [DATASHEET]
8284E–AVR–02/2013
Note: 1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20mA at V
CC
= 5V, 10mA at V
CC
= 3V for Port B and 10mA at
V
CC
= 5V, 5mA at V
CC
= 3V for all other ports) under steady state conditions (non-transient), the following must be observed:
TQFP and QFN/MLF Package:
1] The sum of all IOL, for all ports, should not exceed 400mA.
2] The sum of all IOL, for ports A0 - A7, C4 - C7, G2 should not exceed 100mA.
3] The sum of all IOL, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100mA.
4] The sum of all IOL, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100mA.
5] The sum of all IOL, for ports F0 - F7, should not exceed 100mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
4. Although each I/O port can source more than the test conditions (20mA at V
CC
= 5V, 10mA at V
CC
= 3V for Port B and 10mA
at V
CC
= 5V, 5 mA at V
CC
= 3V for all other ports) under steady state conditions (non-transient), the following must be
observed:
TQFP and QFN/MLF Package:
1] The sum of all IOH, for all ports, should not exceed 400mA.
2] The sum of all IOH, for ports A0 - A7, C4 - C7, G2 should not exceed 100mA.
3] The sum of all IOH, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100mA.
4] The sum of all IOH, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100mA.
5] The sum of all IOH, for ports F0 - F7, should not exceed 100mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition
5. Largest value for ATmega 329P and ATmega3290P.
30.2.1 Current consumption ATmega169PA
Notes: 1. All bits set in the “Power Reduction Register” on page 34.
V
ACIO
Analog Comparator
Input Offset Voltage
V
CC
= 5V
V
in
= V
CC
/2
<10 40 mV
I
ACLK
Analog Comparator
Input Leakage Current
V
CC
= 5V
V
in
= V
CC
/2
-50 50 nA
t
ACPD
Analog Comparator
Propagation Delay
V
CC
= 2.7V
V
CC
= 4.0V
750
500
ns
Table 30-2. Current consumption ATmega169PA T
A
= -40C to 105C, V
CC
= 1.8V to 5.5V (unless otherwise noted)
Symbol Parameter Condition Min. Typ. Max. Units
I
CC
Power Supply Current
(1)
Active 1MHz, V
CC
= 2V 0.4 0.5 mA
Active 4MHz, V
CC
= 3V 2.3 2.8 mA
Active 8MHz, V
CC
= 5V 9 11 mA
Idle 1MHz, V
CC
= 2V 0.1 0.2 mA
Idle 4MHz, V
CC
= 3V 0.8 0.9 mA
Idle 8MHz, V
CC
= 5V 3.1 3.3 mA
Power-save mode
32kHz TOSC enabled,
V
CC
= 1.8V
0.6 1.8 µA
32kHz TOSC enabled,
V
CC
= 3V
0.9 3 µA
Power-down mode
WDT enabled, V
CC
= 3V 7 11 µA
WDT disabled, V
CC
= 3V 0.2 2.5 µA
Table 30-1. T
A
= -40C to 105C, V
CC
= 1.8V to 5.5V (unless otherwise noted) (Continued)
Symbol Parameter Condition Min. Typ. Max. Units