Datasheet
Table Of Contents
- Features
- 1. Pin Configurations
- 2. Overview
- 3. Resources
- 4. Data Retention
- 5. About Code Examples
- 6. Capacitive touch sensing
- 7. AVR CPU Core
- 8. AVR Memories
- 9. System Clock and Clock Options
- 10. Power Management and Sleep Modes
- 11. System Control and Reset
- 12. Interrupts
- 13. External Interrupts
- 13.1 Pin Change Interrupt Timing
- 13.2 Register Description
- 13.2.1 EICRA – External Interrupt Control Register A
- 13.2.2 EIMSK – External Interrupt Mask Register
- 13.2.3 EIFR – External Interrupt Flag Registe
- 13.2.4 PCMSK3 – Pin Change Mask Register 3(1)
- 13.2.5 PCMSK2 – Pin Change Mask Register 2(1)
- 13.2.6 PCMSK1 – Pin Change Mask Register 1
- 13.2.7 PCMSK0 – Pin Change Mask Register 0
- 14. I/O-Ports
- 14.1 Overview
- 14.2 Ports as General Digital I/O
- 14.3 Alternate Port Functions
- 14.4 Register Description
- 14.4.1 MCUCR – MCU Control Register
- 14.4.2 PORTA – Port A Data Register
- 14.4.3 DDRA – Port A Data Direction Register
- 14.4.4 PINA – Port A Input Pins Address
- 14.4.5 PORTB – Port B Data Register
- 14.4.6 DDRB – Port B Data Direction Register
- 14.4.7 PINB – Port B Input Pins Address
- 14.4.8 PORTC – Port C Data Register
- 14.4.9 DDRC – Port C Data Direction Register
- 14.4.10 PINC – Port C Input Pins Address
- 14.4.11 PORTD – Port D Data Register
- 14.4.12 DDRD – Port D Data Direction Register
- 14.4.13 PIND – Port D Input Pins Address
- 14.4.14 PORTE – Port E Data Register
- 14.4.15 DDRE – Port E Data Direction Register
- 14.4.16 PINE – Port E Input Pins Address
- 14.4.17 PORTF – Port F Data Register
- 14.4.18 DDRF – Port F Data Direction Register
- 14.4.19 PINF – Port F Input Pins Address
- 14.4.20 PORTG – Port G Data Register
- 14.4.21 DDRG – Port G Data Direction Register
- 14.4.22 PING – Port G Input Pins Address
- 14.4.23 PORTH – Port H Data Register(1)
- 14.4.24 DDRH – Port H Data Direction Register(1)
- 14.4.25 PINH – Port H Input Pins Address(1)
- 14.4.26 PORTJ – Port J Data Register(1)
- 14.4.27 DDRJ – Port J Data Direction Register(1)
- 14.4.28 PINJ – Port J Input Pins Address(1)
- 15. 8-bit Timer/Counter0 with PWM
- 16. Timer/Counter0 and Timer/Counter1 Prescalers
- 17. 16-bit Timer/Counter1
- 17.1 Features
- 17.2 Overview
- 17.3 Accessing 16-bit Registers
- 17.4 Timer/Counter Clock Sources
- 17.5 Counter Unit
- 17.6 Input Capture Unit
- 17.7 Output Compare Units
- 17.8 Compare Match Output Unit
- 17.9 Modes of Operation
- 17.10 Timer/Counter Timing Diagrams
- 17.11 Register Description
- 17.11.1 TCCR1A – Timer/Counter1 Control Register A
- 17.11.2 TCCR1B – Timer/Counter1 Control Register B
- 17.11.3 TCCR1C – Timer/Counter1 Control Register C
- 17.11.4 TCNT1H and TCNT1L – Timer/Counter1
- 17.11.5 OCR1AH and OCR1AL – Output Compare Register 1 A
- 17.11.6 OCR1BH and OCR1BL – Output Compare Register 1 B
- 17.11.7 ICR1H and ICR1L – Input Capture Register 1
- 17.11.8 TIMSK1 – Timer/Counter1 Interrupt Mask Register
- 17.11.9 TIFR1 – Timer/Counter1 Interrupt Flag Register
- 18. 8-bit Timer/Counter2 with PWM and Asynchronous Operation
- 18.1 Features
- 18.2 Overview
- 18.3 Timer/Counter Clock Sources
- 18.4 Counter Unit
- 18.5 Output Compare Unit
- 18.6 Compare Match Output Unit
- 18.7 Modes of Operation
- 18.8 Timer/Counter Timing Diagrams
- 18.9 Asynchronous Operation of Timer/Counter2
- 18.10 Timer/Counter Prescaler
- 18.11 Register Description
- 18.11.1 TCCR2A – Timer/Counter Control Register A
- 18.11.2 TCNT2 – Timer/Counter Register
- 18.11.3 OCR2A – Output Compare Register A
- 18.11.4 ASSR – Asynchronous Status Register
- 18.11.5 TIMSK2 – Timer/Counter2 Interrupt Mask Register
- 18.11.6 TIFR2 – Timer/Counter2 Interrupt Flag Register
- 18.11.7 GTCCR – General Timer/Counter Control Register
- 19. SPI – Serial Peripheral Interface
- 20. USART0
- 20.1 Features
- 20.2 Overview
- 20.3 Clock Generation
- 20.4 Frame Formats
- 20.5 USART Initialization
- 20.6 Data Transmission – The USART Transmitter
- 20.7 Data Reception – The USART Receiver
- 20.8 Asynchronous Data Reception
- 20.9 Multi-processor Communication Mode
- 20.10 Examples of Baud Rate Setting
- 20.11 Register Description
- 21. USI – Universal Serial Interface
- 22. Analog Comparator
- 23. Analog to Digital Converter
- 24. JTAG Interface and On-chip Debug System
- 25. IEEE 1149.1 (JTAG) Boundary-scan
- 26. Boot Loader Support – Read-While-Write Self-Programming
- 26.1 Features
- 26.2 Overview
- 26.3 Application and Boot Loader Flash Sections
- 26.4 Read-While-Write and No Read-While-Write Flash Sections
- 26.5 Boot Loader Lock Bits
- 26.6 Entering the Boot Loader Program
- 26.7 Addressing the Flash During Self-Programming
- 26.8 Self-Programming the Flash
- 26.8.1 Performing Page Erase by SPM
- 26.8.2 Filling the Temporary Buffer (Page Loading)
- 26.8.3 Performing a Page Write
- 26.8.4 Using the SPM Interrupt
- 26.8.5 Consideration While Updating BLS
- 26.8.6 Prevent Reading the RWW Section During Self-Programming
- 26.8.7 Setting the Boot Loader Lock Bits by SPM
- 26.8.8 EEPROM Write Prevents Writing to SPMCSR
- 26.8.9 Reading the Fuse and Lock Bits from Software
- 26.8.10 Preventing Flash Corruption
- 26.8.11 Programming Time for Flash when Using SPM
- 26.8.12 Simple Assembly Code Example for a Boot Loader
- 26.8.13 Atmel ATmega325/3250/645/6450 Boot Loader Parameters
- 26.9 Register Description
- 27. Memory Programming
- 27.1 Program And Data Memory Lock Bits
- 27.2 Fuse Bits
- 27.3 Signature Bytes
- 27.4 Calibration Byte
- 27.5 Parallel Programming Parameters, Pin Mapping, and Commands
- 27.6 Parallel Programming
- 27.6.1 Enter Programming Mode
- 27.6.2 Considerations for Efficient Programming
- 27.6.3 Chip Erase
- 27.6.4 Programming the Flash
- 27.6.5 Programming the EEPROM
- 27.6.6 Reading the Flash
- 27.6.7 Reading the EEPROM
- 27.6.8 Programming the Fuse Low Bits
- 27.6.9 Programming the Fuse High Bits
- 27.6.10 Programming the Extended Fuse Bits
- 27.6.11 Programming the Lock Bits
- 27.6.12 Reading the Fuse and Lock Bits
- 27.6.13 Reading the Signature Bytes
- 27.6.14 Reading the Calibration Byte
- 27.6.15 Parallel Programming Characteristics
- 27.7 Serial Downloading
- 27.8 Programming via the JTAG Interface
- 27.8.1 Programming Specific JTAG Instructions
- 27.8.2 AVR_RESET (0xC)
- 27.8.3 PROG_ENABLE (0x4)
- 27.8.4 PROG_COMMANDS (0x5)
- 27.8.5 PROG_PAGELOAD (0x6)
- 27.8.6 PROG_PAGEREAD (0x7)
- 27.8.7 Data Registers
- 27.8.8 Reset Register
- 27.8.9 Programming Enable Register
- 27.8.10 Programming Command Register
- 27.8.11 Flash Data Byte Register
- 27.8.12 Programming Algorithm
- 27.8.13 Entering Programming Mode
- 27.8.14 Leaving Programming Mode
- 27.8.15 Performing Chip Erase
- 27.8.16 Programming the Flash
- 27.8.17 Reading the Flash
- 27.8.18 Programming the EEPROM
- 27.8.19 Reading the EEPROM
- 27.8.20 Programming the Fuses
- 27.8.21 Programming the Lock Bits
- 27.8.22 Reading the Fuses and Lock Bits
- 27.8.23 Reading the Signature Bytes
- 27.8.24 Reading the Calibration Byte
- 28. Electrical Characteristics
- 29. Typical Characteristics
- 29.1 Active Supply Current
- 29.2 Idle Supply Current
- 29.3 Supply Current of I/O modules
- 29.4 Power-down Supply Current
- 29.5 Power-save Supply Current
- 29.6 Standby Supply Current
- 29.7 Pin Pull-up
- 29.8 Pin Driver Strength
- 29.9 Pin Thresholds and hysteresis
- 29.10 BOD Thresholds and Analog Comparator Offset
- 29.11 Internal Oscillator Speed
- 29.12 Current Consumption of Peripheral Units
- 29.13 Current Consumption in Reset and Reset Pulsewidth
- 30. Register Summary
- 31. Instruction Set Summary
- 32. Ordering Information
- 33. Packaging Information
- 34. Errata
- 35. Datasheet Revision History
- 35.1 Rev. 2570N – 05/11
- 35.2 Rev. 2570M – 04/11
- 35.3 Rev. 2570L – 08/07
- 35.4 Rev. 2570K – 04/07
- 35.5 Rev. 2570J – 11/06
- 35.6 Rev. 2570I – 07/06
- 35.7 Rev. 2570H – 06/06
- 35.8 Rev. 2570G – 04/06
- 35.9 Rev. 2570F – 03/06
- 35.10 Rev. 2570E – 03/06
- 35.11 Rev. 2570D – 05/05
- 35.12 Rev. 2570C – 11/04
- 35.13 Rev. 2570B – 09/04
- 35.14 Rev. 2570A – 09/04
- Table of Contents
258
2570N–AVR–05/11
ATmega325/3250/645/6450
• Page Write to the RWW section: The NRWW section can be read during the Page Write.
• Page Write to the NRWW section: The CPU is halted during the operation.
26.8.4 Using the SPM Interrupt
If the SPM interrupt is enabled, the SPM interrupt will generate a constant interrupt when the
SPMEN bit in SPMCSR is cleared. This means that the interrupt can be used instead of polling
the SPMCSR Register in software. When using the SPM interrupt, the Interrupt Vectors should
be moved to the BLS section to avoid that an interrupt is accessing the RWW section when it is
blocked for reading. How to move the interrupts is described in “Interrupts” on page 49.
26.8.5 Consideration While Updating BLS
Special care must be taken if the user allows the Boot Loader section to be updated by leaving
Boot Lock bit11 unprogrammed. An accidental write to the Boot Loader itself can corrupt the
entire Boot Loader, and further software updates might be impossible. If it is not necessary to
change the Boot Loader software itself, it is recommended to program the Boot Lock bit11 to
protect the Boot Loader software from any internal software changes.
26.8.6 Prevent Reading the RWW Section During Self-Programming
During Self-Programming (either Page Erase or Page Write), the RWW section is always
blocked for reading. The user software itself must prevent that this section is addressed during
the self programming operation. The RWWSB in the SPMCSR will be set as long as the RWW
section is busy. During Self-Programming the Interrupt Vector table should be moved to the BLS
as described in “Interrupts” on page 49, or the interrupts must be disabled. Before addressing
the RWW section after the programming is completed, the user software must clear the
RWWSB by writing the RWWSRE. See “Simple Assembly Code Example for a Boot Loader” on
page 260 for an example.
26.8.7 Setting the Boot Loader Lock Bits by SPM
To set the Boot Loader Lock bits and general Lock bits, write the desired data to R0, write
“X0001001” to SPMCSR and execute SPM within four clock cycles after writing SPMCSR.
See Table 26-2 and Table 26-3 for how the different settings of the Boot Loader bits affect the
Flash access.
If bits 5..0 in R0 are cleared (zero), the corresponding Lock bit will be programmed if an SPM
instruction is executed within four cycles after BLBSET and SPMEN are set in SPMCSR. The Z-
pointer is don’t care during this operation, but for future compatibility it is recommended to load
the Z-pointer with 0x0001 (same as used for reading the Lock bits). For future compatibility it is
also recommended to set bits 7, and 6 in R0 to “1” when writing the Lock bits. When program-
ming the Lock bits the entire Flash can be read during the operation.
26.8.8 EEPROM Write Prevents Writing to SPMCSR
Note that an EEPROM write operation will block all software programming to Flash. Reading the
Fuses and Lock bits from software will also be prevented during the EEPROM write operation. It
is recommended that the user checks the status bit (EEWE) in the EECR Register and verifies
that the bit is cleared before writing to the SPMCSR Register.
Bit 76543210
R0 1 1 BLB12 BLB11 BLB02 BLB01 LB2 LB1