Datasheet
Table Of Contents
- Features
- 1. Pin Configurations
- 2. Overview
- 3. Resources
- 4. Data Retention
- 5. About Code Examples
- 6. Capacitive touch sensing
- 7. AVR CPU Core
- 8. AVR Memories
- 9. System Clock and Clock Options
- 10. Power Management and Sleep Modes
- 11. System Control and Reset
- 12. Interrupts
- 13. External Interrupts
- 13.1 Pin Change Interrupt Timing
- 13.2 Register Description
- 13.2.1 EICRA – External Interrupt Control Register A
- 13.2.2 EIMSK – External Interrupt Mask Register
- 13.2.3 EIFR – External Interrupt Flag Registe
- 13.2.4 PCMSK3 – Pin Change Mask Register 3(1)
- 13.2.5 PCMSK2 – Pin Change Mask Register 2(1)
- 13.2.6 PCMSK1 – Pin Change Mask Register 1
- 13.2.7 PCMSK0 – Pin Change Mask Register 0
- 14. I/O-Ports
- 14.1 Overview
- 14.2 Ports as General Digital I/O
- 14.3 Alternate Port Functions
- 14.4 Register Description
- 14.4.1 MCUCR – MCU Control Register
- 14.4.2 PORTA – Port A Data Register
- 14.4.3 DDRA – Port A Data Direction Register
- 14.4.4 PINA – Port A Input Pins Address
- 14.4.5 PORTB – Port B Data Register
- 14.4.6 DDRB – Port B Data Direction Register
- 14.4.7 PINB – Port B Input Pins Address
- 14.4.8 PORTC – Port C Data Register
- 14.4.9 DDRC – Port C Data Direction Register
- 14.4.10 PINC – Port C Input Pins Address
- 14.4.11 PORTD – Port D Data Register
- 14.4.12 DDRD – Port D Data Direction Register
- 14.4.13 PIND – Port D Input Pins Address
- 14.4.14 PORTE – Port E Data Register
- 14.4.15 DDRE – Port E Data Direction Register
- 14.4.16 PINE – Port E Input Pins Address
- 14.4.17 PORTF – Port F Data Register
- 14.4.18 DDRF – Port F Data Direction Register
- 14.4.19 PINF – Port F Input Pins Address
- 14.4.20 PORTG – Port G Data Register
- 14.4.21 DDRG – Port G Data Direction Register
- 14.4.22 PING – Port G Input Pins Address
- 14.4.23 PORTH – Port H Data Register(1)
- 14.4.24 DDRH – Port H Data Direction Register(1)
- 14.4.25 PINH – Port H Input Pins Address(1)
- 14.4.26 PORTJ – Port J Data Register(1)
- 14.4.27 DDRJ – Port J Data Direction Register(1)
- 14.4.28 PINJ – Port J Input Pins Address(1)
- 15. 8-bit Timer/Counter0 with PWM
- 16. Timer/Counter0 and Timer/Counter1 Prescalers
- 17. 16-bit Timer/Counter1
- 17.1 Features
- 17.2 Overview
- 17.3 Accessing 16-bit Registers
- 17.4 Timer/Counter Clock Sources
- 17.5 Counter Unit
- 17.6 Input Capture Unit
- 17.7 Output Compare Units
- 17.8 Compare Match Output Unit
- 17.9 Modes of Operation
- 17.10 Timer/Counter Timing Diagrams
- 17.11 Register Description
- 17.11.1 TCCR1A – Timer/Counter1 Control Register A
- 17.11.2 TCCR1B – Timer/Counter1 Control Register B
- 17.11.3 TCCR1C – Timer/Counter1 Control Register C
- 17.11.4 TCNT1H and TCNT1L – Timer/Counter1
- 17.11.5 OCR1AH and OCR1AL – Output Compare Register 1 A
- 17.11.6 OCR1BH and OCR1BL – Output Compare Register 1 B
- 17.11.7 ICR1H and ICR1L – Input Capture Register 1
- 17.11.8 TIMSK1 – Timer/Counter1 Interrupt Mask Register
- 17.11.9 TIFR1 – Timer/Counter1 Interrupt Flag Register
- 18. 8-bit Timer/Counter2 with PWM and Asynchronous Operation
- 18.1 Features
- 18.2 Overview
- 18.3 Timer/Counter Clock Sources
- 18.4 Counter Unit
- 18.5 Output Compare Unit
- 18.6 Compare Match Output Unit
- 18.7 Modes of Operation
- 18.8 Timer/Counter Timing Diagrams
- 18.9 Asynchronous Operation of Timer/Counter2
- 18.10 Timer/Counter Prescaler
- 18.11 Register Description
- 18.11.1 TCCR2A – Timer/Counter Control Register A
- 18.11.2 TCNT2 – Timer/Counter Register
- 18.11.3 OCR2A – Output Compare Register A
- 18.11.4 ASSR – Asynchronous Status Register
- 18.11.5 TIMSK2 – Timer/Counter2 Interrupt Mask Register
- 18.11.6 TIFR2 – Timer/Counter2 Interrupt Flag Register
- 18.11.7 GTCCR – General Timer/Counter Control Register
- 19. SPI – Serial Peripheral Interface
- 20. USART0
- 20.1 Features
- 20.2 Overview
- 20.3 Clock Generation
- 20.4 Frame Formats
- 20.5 USART Initialization
- 20.6 Data Transmission – The USART Transmitter
- 20.7 Data Reception – The USART Receiver
- 20.8 Asynchronous Data Reception
- 20.9 Multi-processor Communication Mode
- 20.10 Examples of Baud Rate Setting
- 20.11 Register Description
- 21. USI – Universal Serial Interface
- 22. Analog Comparator
- 23. Analog to Digital Converter
- 24. JTAG Interface and On-chip Debug System
- 25. IEEE 1149.1 (JTAG) Boundary-scan
- 26. Boot Loader Support – Read-While-Write Self-Programming
- 26.1 Features
- 26.2 Overview
- 26.3 Application and Boot Loader Flash Sections
- 26.4 Read-While-Write and No Read-While-Write Flash Sections
- 26.5 Boot Loader Lock Bits
- 26.6 Entering the Boot Loader Program
- 26.7 Addressing the Flash During Self-Programming
- 26.8 Self-Programming the Flash
- 26.8.1 Performing Page Erase by SPM
- 26.8.2 Filling the Temporary Buffer (Page Loading)
- 26.8.3 Performing a Page Write
- 26.8.4 Using the SPM Interrupt
- 26.8.5 Consideration While Updating BLS
- 26.8.6 Prevent Reading the RWW Section During Self-Programming
- 26.8.7 Setting the Boot Loader Lock Bits by SPM
- 26.8.8 EEPROM Write Prevents Writing to SPMCSR
- 26.8.9 Reading the Fuse and Lock Bits from Software
- 26.8.10 Preventing Flash Corruption
- 26.8.11 Programming Time for Flash when Using SPM
- 26.8.12 Simple Assembly Code Example for a Boot Loader
- 26.8.13 Atmel ATmega325/3250/645/6450 Boot Loader Parameters
- 26.9 Register Description
- 27. Memory Programming
- 27.1 Program And Data Memory Lock Bits
- 27.2 Fuse Bits
- 27.3 Signature Bytes
- 27.4 Calibration Byte
- 27.5 Parallel Programming Parameters, Pin Mapping, and Commands
- 27.6 Parallel Programming
- 27.6.1 Enter Programming Mode
- 27.6.2 Considerations for Efficient Programming
- 27.6.3 Chip Erase
- 27.6.4 Programming the Flash
- 27.6.5 Programming the EEPROM
- 27.6.6 Reading the Flash
- 27.6.7 Reading the EEPROM
- 27.6.8 Programming the Fuse Low Bits
- 27.6.9 Programming the Fuse High Bits
- 27.6.10 Programming the Extended Fuse Bits
- 27.6.11 Programming the Lock Bits
- 27.6.12 Reading the Fuse and Lock Bits
- 27.6.13 Reading the Signature Bytes
- 27.6.14 Reading the Calibration Byte
- 27.6.15 Parallel Programming Characteristics
- 27.7 Serial Downloading
- 27.8 Programming via the JTAG Interface
- 27.8.1 Programming Specific JTAG Instructions
- 27.8.2 AVR_RESET (0xC)
- 27.8.3 PROG_ENABLE (0x4)
- 27.8.4 PROG_COMMANDS (0x5)
- 27.8.5 PROG_PAGELOAD (0x6)
- 27.8.6 PROG_PAGEREAD (0x7)
- 27.8.7 Data Registers
- 27.8.8 Reset Register
- 27.8.9 Programming Enable Register
- 27.8.10 Programming Command Register
- 27.8.11 Flash Data Byte Register
- 27.8.12 Programming Algorithm
- 27.8.13 Entering Programming Mode
- 27.8.14 Leaving Programming Mode
- 27.8.15 Performing Chip Erase
- 27.8.16 Programming the Flash
- 27.8.17 Reading the Flash
- 27.8.18 Programming the EEPROM
- 27.8.19 Reading the EEPROM
- 27.8.20 Programming the Fuses
- 27.8.21 Programming the Lock Bits
- 27.8.22 Reading the Fuses and Lock Bits
- 27.8.23 Reading the Signature Bytes
- 27.8.24 Reading the Calibration Byte
- 28. Electrical Characteristics
- 29. Typical Characteristics
- 29.1 Active Supply Current
- 29.2 Idle Supply Current
- 29.3 Supply Current of I/O modules
- 29.4 Power-down Supply Current
- 29.5 Power-save Supply Current
- 29.6 Standby Supply Current
- 29.7 Pin Pull-up
- 29.8 Pin Driver Strength
- 29.9 Pin Thresholds and hysteresis
- 29.10 BOD Thresholds and Analog Comparator Offset
- 29.11 Internal Oscillator Speed
- 29.12 Current Consumption of Peripheral Units
- 29.13 Current Consumption in Reset and Reset Pulsewidth
- 30. Register Summary
- 31. Instruction Set Summary
- 32. Ordering Information
- 33. Packaging Information
- 34. Errata
- 35. Datasheet Revision History
- 35.1 Rev. 2570N – 05/11
- 35.2 Rev. 2570M – 04/11
- 35.3 Rev. 2570L – 08/07
- 35.4 Rev. 2570K – 04/07
- 35.5 Rev. 2570J – 11/06
- 35.6 Rev. 2570I – 07/06
- 35.7 Rev. 2570H – 06/06
- 35.8 Rev. 2570G – 04/06
- 35.9 Rev. 2570F – 03/06
- 35.10 Rev. 2570E – 03/06
- 35.11 Rev. 2570D – 05/05
- 35.12 Rev. 2570C – 11/04
- 35.13 Rev. 2570B – 09/04
- 35.14 Rev. 2570A – 09/04
- Table of Contents
115
2570N–AVR–05/11
ATmega325/3250/645/6450
Figure 17-6. CTC Mode, Timing Diagram
An interrupt can be generated at each time the counter value reaches the TOP value by either
using the OCF1A or ICF1 Flag according to the register used to define the TOP value. If the
interrupt is enabled, the interrupt handler routine can be used for updating the TOP value. How-
ever, changing the TOP to a value close to BOTTOM when the counter is running with none or a
low prescaler value must be done with care since the CTC mode does not have the double buff-
ering feature. If the new value written to OCR1A or ICR1 is lower than the current value of
TCNT1, the counter will miss the compare match. The counter will then have to count to its max-
imum value (0xFFFF) and wrap around starting at 0x0000 before the compare match can occur.
In many cases this feature is not desirable. An alternative will then be to use the fast PWM mode
using OCR1A for defining TOP (WGM13:0 = 15) since the OCR1A then will be double buffered.
For generating a waveform output in CTC mode, the OC1A output can be set to toggle its logical
level on each compare match by setting the Compare Output mode bits to toggle mode
(COM1A1:0 = 1). The OC1A value will not be visible on the port pin unless the data direction for
the pin is set to output (DDR_OC1A = 1). The waveform generated will have a maximum fre-
quency of f
OC
1
A
= f
clk_I/O
/2 when OCR1A is set to zero (0x0000). The waveform frequency is
defined by the following equation:
The N variable represents the prescaler factor (1, 8, 64, 256, or 1024).
As for the Normal mode of operation, the TOV1 Flag is set in the same timer clock cycle that the
counter counts from MAX to 0x0000.
17.9.3 Fast PWM Mode
The fast Pulse Width Modulation or fast PWM mode (WGM13:0 = 5, 6, 7, 14, or 15) provides a
high frequency PWM waveform generation option. The fast PWM differs from the other PWM
options by its single-slope operation. The counter counts from BOTTOM to TOP then restarts
from BOTTOM. In non-inverting Compare Output mode, the Output Compare (OC1x) is cleared
on the compare match between TCNT1 and OCR1x, and set at BOTTOM. In inverting Compare
Output mode output is set on compare match and cleared at BOTTOM. Due to the single-slope
operation, the operating frequency of the fast PWM mode can be twice as high as the phase cor-
rect and phase and frequency correct PWM modes that use dual-slope operation. This high
frequency makes the fast PWM mode well suited for power regulation, rectification, and DAC
applications. High frequency allows physically small sized external components (coils, capaci-
tors), hence reduces total system cost.
TCNTn
OCnA
(Toggle)
OCnA Interrupt Flag Set
or ICFn Interrupt Flag Set
(Interrupt on TOP)
1 4
Period
2 3
(COMnA1:0 = 1)
f
OCnA
f
clk_I/O
2 N 1 OCRnA+()⋅⋅
-------------------------------------------------- -=